Make it posible to configure the element to obtain the timestamps from
reference timestamp meta data instead of using the ntp-offset property,
or estimating its own offset. Currently the only time format supported
is "timestamp/x-unix", i.e. UTC time expressed in the unix time epoch.
In addition the custom event GstNtpOffset has been renamed to
GstOnvifTimestamp, to reflect that it is not necessarily used to convey
the ntp-offset. As a consequence we had to modify a couple of files in
the rtsp-server as well.
Fixes#984
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1683>
This patch fixes a seg.fault in gst_structure_new() with warnings as below.
GLib-GObject-WARNING **:
../gobject/gtype.c:4330: type id '0' is invalid
GLib-GObject-WARNING **:
can't peek value table for type '<invalid>' which is not currently referenced
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1918>
On GstVideoDecoder::{drain,flush}, we send null packet with
CUVID_PKT_ENDOFSTREAM flag to drain out decoder. Which will
reset CUVID parser as well.
To continue decoding after the drain, the next input buffer
should include sequence headers otherwise CUVID parser will
not report any decodeable frame.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1911>
There could be a case where the new program has the same program number as the
previous one ... but is actually located on a PID previously used for elementary
stream. In that case the program is guaranteed to not be an update of the
previous program but a completely new one.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1893>
We need to be able to look for programs by their PID also. Using a hash table
was a bit sub-par (and overkill) for storing a range of programs.
This is needed because there could potentially be two programs with the same
program id but different PMT PID (while one is being deactivated the new one
would "exist").
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1893>
This commit modifies the interleave calculation to allow growing when incoming
data is before the segment start.
The rationale is that there is no requirement whatsoever for data before the
segment start to be "coherent" on all streams.
For example, a demuxer could rightfully send data from the video stream from the
previous keyframe (potentially quite a bit before the segment start) and the
audio from just before the segment start.
This will activate the same logic as growing the interleave when some streams
haven't received buffers yet.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1892>
* When a stream receives EOS, it will no longer change, we shouldn't take that
stream into account for interleave calculation.
* When streams (re)appear, we do not want to grow the initial interleave values
to excessive values. Instead of setting it to a default of 5s, progressively
grow it to that maximum.
* When the status of input streams change (i.e. going to/from "some haven't
received data yet" and "all have received data"), update the interleave
immediately instead of waiting for (potentially) 5s of data before updating
it.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1892>
The point here is that rtpsession will create a new rtpsource when
the field "rtx-ssrc" is present, and when not doing rtx, that means
a random ssrc will create a new rtpsource that will be included in RTCP
messages for the current session.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1882>
Instead of using GstMiniObject to hold H264 frame, now it uses a plain
structure. Besides, instead of holding a reference to
GstVideoCodecFrame, the H264 frame structure is set as a
GstVideoCodecFrame user data.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1856>
According to va_dec_hevc.h, pic_param->st_rps_bits should be set
for accelorater to skip parsing the *short_term_ref_pic_set
(num_short_term_ref_pic_sets) structure.
Also modified fill_picture to get parser info as a parameter,
in order to get slide_hdr->short_term_ref_pic_set_size.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1886>
Fix a small race where a group can receive stream-start
and post a pending buffering message just as another
thread posts a different buffering message, causing them
to be received by the application out of order. In the
worst case, this leads the application receiving a
stale 99% buffering message and going back to buffering
right after the 100% buffering message.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1840>
Apparently GtkSharp expects each object has only one ToggleRef at any
time. Assigning element.Handle into Raw has a consequence that second
ToggleRef attempts to get created but fails on g_object_unref () that
breaks a GObject assertion:
toggle_refs_notify: assertion failed: (tstack.n_toggle_refs == 1)
This is because toggle references should be removed with
g_object_remove_toggle_ref(), not a simple unref().
In order to avoid duplicate toggle references, introduce
ElementFactory.MakeRaw(), which creates a GstElement without its
accompanying C# object. The returned raw pointer can be assigned into
another GLib.Object without trouble.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1885>
And use the output segment position for the outgoing timestamp while it
is. This is needed to delay the calculation of `output_ts_offset` until
we actually have a usable timestamp, as tsmux will output a few initial
packets while `last_ts` is still unset.
Without this, the calculation would use the initial `0` value, which did
not have the intended effect of making VBR mode behave like CBR mode,
but always calculated an offset equal to the selected start time.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1884>
Fix suppression to support release and debug builds.
Here is the debug build call stack:
```
==10707== by 0x48B5520: g_malloc (gmem.c:106)
==10707== by 0x48D19DC: g_slice_alloc (gslice.c:1069)
==10707== by 0x48D3947: g_slist_copy_deep (gslist.c:619)
==10707== by 0x48D38B8: g_slist_copy (gslist.c:567)
==10707== by 0x4ADC90B: gst_debug_remove_with_compare_func (gstinfo.c:1504)
```
In release build `g_slist_copy (gslist.c:567)` got inlined:
```
==15419== by 0x48963E0: g_malloc (gmem.c:106)
==15419== by 0x48AA382: g_slice_alloc (gslice.c:1069)
==15419== by 0x48AB732: g_slist_copy_deep (gslist.c:619)
==15419== by 0x4A39B8F: gst_debug_remove_with_compare_func (gstinfo.c:1504)
```
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1814>
When doing only a single stream of audio/video this hardly matters,
but when doing many at the same time, the fact that you have to get
a hold of the glib global type-system lock every time you process a buffer,
means that there is a limit to how many streams you can process in
parallel.
Luckily the fix is very simple, by doing a cast rather than a full
type-check.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1873>
There is a chance that pool->buffers[index] sets BUFFER_STATE_QUEUED, but
it has not been queued yet which makes pool->buffers[index] still NULL.
At this time, if pool_streamff release all buffers with BUFFER_STATE_QUEUED
state regardless of whether the buffer is NULL or not, it will cause segfault.
To fix this, also check buffer when streamoff release buffer.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1842>
When tunneling over HTTP, if connection on the second channel happens
before the control timer is created we may trigger an assert in
rtsp_ctrl_timeout_remove(). Avoid that by taking the priv->lock before
attaching the client thread to the context.
Fixes#1025
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1867>
When there is vpp scaling downstream, we need to make sure SFC is not
triggered because vpp may fall into passthrough mode which causes
the decoder negotiation to create src caps with vpp scaled width/height.
This patch includes bitstream's original size in first query with
downstream in gst_msdkdec_src_caps, which is the same for what we do for
color format in this query. This is to ensure SFC scaling starts to
work only when downstream directly asks for a different size instead of
through vpp.
Note that here SFC scaling follows the same behavior as msdkvpp:
if user only changes width or height, e.g. dec ! video/x-raw,width=xx !,
the height will be modified to the value which fits the original DAR.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1838>
* Hide GstCudaMemory member variables
* Make GstCudaAllocator object GstCudaContext independent
* Set offset/stride of memory correctly via video meta
* Drop GST_BUFFER_POOL_OPTION_VIDEO_ALIGNMENT support.
This implementation actually does not support custom alignment
because we allocate device memory via cuMemAllocPitch
of which alignment is almost uncontrollable
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1834>
* cudaupload/download
- Specify only formats actually we can deal with
nvcodec elements, not all video formats
- Supports CUDA output for download and input for upload in order
to make passthrough possible, like other upload/download elements.
* cudabasetransform
- Reset conversion element if upstream CUDA memory
holds different CUDA context and the element can accept it.
This is the same behavior as corresponding d3d11 filter elements.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1834>
This was to support very old V4L2 kernel. As we moved to DMABuf and can now
detach buffers on renegotiation, the buffer it tries to fix no longer exist.
The risk to blocking indefinitly the application does still exist though.
Fixes#1070
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1861>
When we negotiate with downstream, We should use the intersected
caps of input and output to decide the alignment and stream format.
The current code just uses the input caps which may lack the stream
format.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1837>
The demux now outputs the AV1 stream in "tu" alignment, so we do not need
to detect the input alignment. But the annex b stream format is not recognized
by the demux, we still need to detect that stream format for the first input.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1837>
Decoders that required frame aligmment and didn't have an associated
alpha decoder were skipped. This is because the parser was constructing
caps based on the software alpha decoder, which specify super-frame
alignment.
Iterate over the caps to filter the one that have a matching codec-alpha, with
the semantic the no codec-alpha field means codec-alpha=false. Then if
everything was removed, callback to the original, so that the first non-alpha
decoder will be picked.
Fixes#820
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1855>
Currently for copying the coded buffer onto a GStreamer buffer, the
coded buffer is mapped two times: one for getting the size, and later
for do the actual copy. We can avoid this by doing directly in the
element rather than in the general encoder object.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1845>
We need to always add the RTX/RED/ULPFEC elements as rtpbin will only
call us once to request aux/fec senders/receivers.
We also need to regenerate the media section of the SDP instead of
blindly copying from the previous offer.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1762>
When the size of V4L2 capture or output is changes with VIDIOC_S_FMT,
the device is only required to update the compisition window to fit
inside the new frame size. This can result in captured data only being
updated on a portion of the frame after a resize.
Update the composition window to the default value determined by the
V4L2 device driver whenever the format is changed to make sure that
all image data is composed to its full size.
Fixes#765
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1806>
As specified formally in RFC8851
Each rid description is placed in its own caps field in the structure.
This is very similar to the already existing extmap-$id sdp<->caps
transformations that already exists.
The mapping is as follows:
a=rid:0 direction ';'-separated params
where direction is either 'send' or 'recv'
gets put into a caps structure like so:
rid-0=(string)<"direction","param1","param2",etc>
If there are no rid parameters then the caps structure is generated to
only contain the direction as a single string like:
rid-0=(string)direction
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1760>
Not having this field is equivalent with it being 1/1 so consider
it like that. The generic caps functions are not aware of these
semantics and would consider the caps different, causing a negotiation
failure when caps are changing from caps with to caps without or the
other way around.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1826>
Not having these fields is equivalent with them being mono/0 so consider
them like that. The generic caps functions are not aware of these
semantics and would consider the caps different, causing a negotiation
failure when caps are changing from caps with to caps without or the
other way around.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1826>
Otherwise fetching of the offer will fail with a cryptic error:
```
Traceback (most recent call last):
File "/../gstreamer/subprojects/gst-examples/webrtc/sendrecv/gst/webrtc_sendrecv.py", line 56, in on_offer_created
offer = reply['offer']
TypeError: 'Structure' object is not subscriptable
```
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1821>
```
ERROR peer '5762' not found
Traceback (most recent call last):
File "/../gstreamer/subprojects/gst-examples/webrtc/sendrecv/gst/webrtc_sendrecv.py", line 190, in <module>
res = loop.run_until_complete(c.loop())
File "/usr/lib64/python3.10/asyncio/base_events.py", line 641, in run_until_complete
return future.result()
File "/../gstreamer/subprojects/gst-examples/webrtc/sendrecv/gst/webrtc_sendrecv.py", line 155, in loop
self.close_pipeline()
File "/../gstreamer/subprojects/gst-examples/webrtc/sendrecv/gst/webrtc_sendrecv.py", line 142, in close_pipeline
self.pipe.set_state(Gst.State.NULL)
AttributeError: 'NoneType' object has no attribute 'set_state'
```
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1821>
```
File "/../gstreamer/subprojects/gst-examples/webrtc/sendrecv/gst/webrtc_sendrecv.py", line 189, in <module>
loop.run_until_complete(c.connect())
File "/usr/lib64/python3.10/asyncio/base_events.py", line 641, in run_until_complete
return future.result()
File "/../gstreamer/subprojects/gst-examples/webrtc/sendrecv/gst/webrtc_sendrecv.py", line 40, in connect
self.conn = await websockets.connect(self.server, ssl=sslctx)
File "/home/nirbheek/.local/lib/python3.10/site-packages/websockets/legacy/client.py", line 650, in __await_impl_timeout__
return await asyncio.wait_for(self.__await_impl__(), self.open_timeout)
File "/usr/lib64/python3.10/asyncio/tasks.py", line 445, in wait_for
return fut.result()
File "/home/nirbheek/.local/lib/python3.10/site-packages/websockets/legacy/client.py", line 654, in __await_impl__
transport, protocol = await self._create_connection()
File "/usr/lib64/python3.10/asyncio/base_events.py", line 1080, in create_connection
transport, protocol = await self._create_connection_transport(
File "/usr/lib64/python3.10/asyncio/base_events.py", line 1110, in _create_connection_transport
await waiter
File "/usr/lib64/python3.10/asyncio/sslproto.py", line 631, in _on_handshake_complete
raise handshake_exc
File "/usr/lib64/python3.10/asyncio/sslproto.py", line 676, in _process_write_backlog
ssldata = self._sslpipe.do_handshake(
File "/usr/lib64/python3.10/asyncio/sslproto.py", line 116, in do_handshake
self._sslobj = self._context.wrap_bio(
File "/usr/lib64/python3.10/ssl.py", line 526, in wrap_bio
return self.sslobject_class._create(
File "/usr/lib64/python3.10/ssl.py", line 865, in _create
sslobj = context._wrap_bio(
ssl.SSLError: Cannot create a client socket with a PROTOCOL_TLS_SERVER context (_ssl.c:801)
```
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1821>
asyncio.get_event_loop() will not implicitly create a new event loop
in a future version of Python, so we need to do that explicitly.
```
webrtc_sendrecv.py:188: DeprecationWarning: There is no current event loop
loop = asyncio.get_event_loop()
```
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1821>
If the tracks element was parsed from the SeekEntry, don't
parse it a second time and recreate tracks, as this
loses any tags that were read using the seek table.
If a genuinely new Tracks element is found, do read that
as it is needed for MSE support.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1798>
Remove the symbolic link `gst-uninstalled` which points to `gst-env`.
The `uninstalled` is the old name and the project should stick to a
single name for the procedure.
Remove the term from all the files, exceptions are variables from
dependencies like `uninstalled_variables` from pkgconfig and
`meson-uninstalled`.
Adjust mentions of the script in the documentation and README.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1743>
Do not maintain similar build instructions within each gst-plugins-*
subproject and the subproject/gstreamer subproject. Use the build
instructions from the mono-repository and link to them via hyperlink.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1743>
This a new VA-API implementation of a H264 encoder.
It can control the GOP and parameter settings, while the MV searching,
VCL and the rate control algorithm are implemented by VA drivers and HW.
It supports most of the common usage options in H264, but still lacks
of look ahead, field, B frame weighted prediction, etc.
Co-authored-by: Victor Jaquez <vjaquez@igalia.com>
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1051>
The g_queue_clear_full() and g_array_copy() functions in the glib
may not be available for the current glib version check, so we add
helper functions to wrap it.
This should be deleted after the glib version bumps.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1051>
LOAD macro relies in m7 being zero for interleaving purposes. Using LOAD
on the m7 register makes it interleave with its new content instead of
with 0.
The effect of this bug was bobbing on some static lines that appeared
over fast-moving content.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1816>
The fd was in different meanings on windows:
POSIX read and write use the fd as a file descriptor.
The gst_poll use the fd as a WSASocket.
This patch use WSASocket as default on windows. This is a temporary measure, because IPC has many different implement. There may be a better way in the future.
See #1044
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1791>
The dynamic resolution changes when
the sequence starts when the decoder detects a coded frame with one or
more of the following parameters different from those previously
established (and reflected by corresponding queries):
1.coded resolution (OUTPUT width and height),
2.visible resolution (selection rectangles),
3.the minimum number of buffers needed for decoding,
4.bit-depth of the bitstream has been changed.
Although gstreamer parser has parsed the stream resolution.
but there are some case that we need to handle resolution change event.
1. bit-depth is different from the negotiated format.
2. the capture buffer count can meet the demand
3. there are some hardware limitations that the decoded resolution may
be larger than the display size. For example, the stream size is
1920x1080, but some vpu may decode it to 1920x1088.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1381>
v4l2videodec do some refactoring so that it can support
dynamic resolution change event.
1.wrap the setup process of capture as a function,
as decoder need setup the capture again when
dynamic resolution change event is received.
2.move the function "remove_padding"
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1381>
This allows downstream of a payloader to know the RTP header's marker
flag without first having to map the buffer and parse the RTP header.
Especially inside RTP header extension implementations this can be
useful to decide which packet corresponds to e.g. the last packet of a
video frame.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1776>
osxaudiodeviceprovider now probes devices more than once to determine
if the device can function as both an input AND and output device.
Previously, if the device provider detected that a device had any output
capabilities, it was treated solely as an Audio/Sink. This causes issues
that have both input and output capabilities (for example, USB interfaces
for professional audio have both input and output channels). Such devices
are now listed as both an Audio/Sink as well as an Audio/Source.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1385>
The RTP payload seems to be required as it carries the frame count
information. Also, gst_rtp_base_payload_allocate_output_buffer had
the second argument incorrect.
Strangely some devices like Shanling MP4 and Sony XM3 would still
work without this while some like the Sony XM4 do not.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1797>
While this is slightly more expensive (~48% slower per random number) it
does not cause any measurable difference when running through a complete
audio conversion pipeline.
On the other hand its random numbers are of much higher quality and on
spectrograms for 32 bit to 24 bit conversion the difference is clearly
visible.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1729>
The instant-rate value in the TrickMode enum is a
flag, but the other values are not. Move instant-rate
to the end of the enum and give it a value large enough
for it to be used without modifying the trick-mode
setting.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1788>
Update x264enc long-name to be more than just the name. Then the
description also was updated to be longer than the long-name, and
similar to the plugin description.
Finally, as I am here, H264 was replaced by H.264 and x264 is only a
plugin (not plugins).
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1771>
They can't be used in any useful way. The type of every GstMemory is
always GST_TYPE_MEMORY and the subtyping relationship has to be
implemented on top of that via the associated allocator and mem_type
string.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1764>
Scenario:
- Source 1 requesting and waiting a clock id
- Source 2 requesting and waiting on a clock id
- Test attempting to crank both sources in the same GstHarness
gst_test_clock_crank() originally dropped locks between the retrieving
of the next clock id and advancing to the next clock id. This would
mean that both sources would race each other attempting to complete
their clock waits. Sometimes the operations would be performed in the
correct order, other times they would not and a FALSE return value would
be produced.
This would lead to an assertion in gst_harness_push_from_src() expecting
that all clock cranks to succeed.
Fix by ensuring that the clock wait produced is dealt with before
processing the next by not dropping the relevant locks after retrieving
the next clock id.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1299>
This is a minimal unit test the show that the stride extrapolation can work
with all pixel format we support. This minimal verify that the extrapolation
match the stride we set into GstVideoInfo with 320x240 for all the pixel
format we support. The tiles formats are skipped, since their stride is
set as two 16bit integers, and we also skip over palette planes.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1567>
As this element is single threaded, we only need to stop the objects to
allow changing the format again. Fixes assertion notably on shutdown and
on some other situation where the format may be set twice without
actually activating the element.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1567>
Many of the legacy APIs, specifically in the Linux Kernel, have a
single stride for the pictures. In this context, it is common
to extrapolate the other strides based on the selected pixel
format. Such function have been copy pasted from video4linux2
plugin into wayland, kms and v4l2codecs plugins.
This patch implements a generalized from of that function and
make it available to everyone through the video library.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1567>
Unlike other simple tiled formats, the Mediatek HW use different tile size
per-plane. The tile size is scaled according to the subsampling. Effectively,
using the name 16L32S to represent linearly layout tiles of size 16x32 bytes
in the Y plane, and 16x16 in the UV plane. In order to make this specificity
discoverable, a new SUBTILES flags have been added.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1567>
If the video4linux device supports norms but has no norm set, norm is
returned as an uninitialized variable after the ioctl call, leading to
gst_v4l2_tuner_get_norm_by_std_id() returning a random norm from the
supported norms. Catch this case and instead return NULL to indicate
that no norm is setup.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1625>
We have the d3d11screencapturesrc element in d3d11 plugin
which is obviously better than this element in terms of performance
and design, so we don't need to make people be confused by two separate elements.
Let's pick the better implementation and remove unnecessary one.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1750>
... instead of round(). Depending on framerate, calculated position
may not be clearly represented by using uint64, 30000/1001 for example.
Then the result of round() can be sliglhtly larger (1ns) than
buffer timestamp. And that will cause unnecessary frame delay.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1747>
It was assumed that the kernel parameters would match with the bitstream value
but instead the author when with another set of value. Surprisingly, this
makes no difference with the resulting fluster score.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1748>
If a serialized event arrives behind a buffer, it should not be send before
it. This fixes the pending event handling so that only early pending events,
the one that arrrived or was generated while the adapter was empty get send
before pushing buffer. All other events are not pushed after.
This issue lead the latency tracer to think our audio encoder did not have any
latency. This was testing with opusenc in a live pipeline.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1266>
Each stream may have its own segment timeline
(i.g., different segment.start or segment.base)
depending on edit-list and composition-to-decode atom.
Make sure whether time position of a stream has been actually
far behind than that of current target stream.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1352>
If present, add '-lsocket' and '-lnsl' to network_deps.
ext/curl/meson.build: add network_deps to dependencies
gst/festival/meson.build: same
sys/shm/meson.build: same
Fixes linking issues on Illumos distros.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1525>
Often, users will need to scale inputs (e.g.
with vaapipostproc) before they are submitted
to the vaapioverlay. However, this results in
multiple VPP passes/operations in the pipeline
which creates unnecessary process overhead.
This change allows for inputs to be submitted
at original scale to vaapioverlay with per-sinkpad
scale dimensions specified so they can be scaled
and blended/composited in a single VPP pass/operation
to avoid the unnecessary process overhead.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1380>
Don't set VAAPI vpp blend flags if alpha == 1.0,
i.e. fully opaque. This can avoid extra processing
overhead on some drivers that apply blending
unconditionally when flags are present, even if the
end result is the same without blend flags (i.e. all
opaque alpha channels).
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1380>
Note that AYUV and AYUV64 formats will be used to expand format
support, especially some packed YUV formats (e.g., Y410, YUY2)
are common DXGI formats used for hardware decoder/encoder on Windows
but those formats cannot be used as a render target. We need to handle
them differently without pixel shader help, using compute shader
for example.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1699>
The libjpeg-turbo internal state might not be correctly initialized for
the first frame in a stream, pull the frame stride from gstreamer frame
metadata instead, which is correct even for the first frame, and which
makes this code consistent with the surrounding lines.
Fixes: e6d83d8f96 ("jpegdec: Support libjpeg-turbo colorspace conversion")
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1687>
It is imperative that the libjpeg-turbo state is properly initialized
before jpeg_start_decompress() is called. Make sure cinfo.out_color_space
and cinfo.raw_data_out are set to their final values matching their peer
caps before calling jpeg_start_decompress().
Fixes: e6d83d8f96 ("jpegdec: Support libjpeg-turbo colorspace conversion")
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1687>
Pull out peer caps checking code into gst_jpeg_turbo_parse_ext_fmt_convert().
This code is used by libjpeg-turbo extras to determine whether peer is capable
of handling buffers into which libjpeg-turbo can directly decode data. This
kind of check must be performed before jpeg_start_decompress() is called in
gst_jpeg_dec_prepare_decode() as well as in gst_jpeg_dec_negotiate(), hence
the common code.
This commit does modify the code a little to make it easier to call from both
call sites without much duplication, hence the extra `if (*clrspc)` test.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1687>
This reverts commit 2aa2477208.
The commit is completely wrong, libjpeg-turbo is perfectly capable
of decoding I420 (YUV) to RGB. The test case provided alongside the
aforementioned commit passes without this revert because it decodes
image of JCS_YCrCb color space, so the new `if (clrspc == JCS_RGB)`
condition is false on that image, and the libjpeg-turbo decoding
does not get used. The real bug is hidden by that commit.
The real problem is in the call order of gst_jpeg_dec_prepare_decode()
and gst_jpeg_dec_negotiate(). The gst_jpeg_dec_prepare_decode() calls
jpeg_start_decompress() which sets up internal state of the libjpeg,
however, neither cinfo.out_color_space nor cinfo.raw_data_out are
set correctly yet. Those two are set up in gst_jpeg_dec_negotiate()
which is called a bit later. Therefore, the real fix is the set up
cinfo.out_color_space and cinfo.raw_data_out before calling
jpeg_start_decompress(). This is however a separate patch.
Fixes: 2aa2477208 ("jpegdec: only allow conversions from RGB")
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1687>
Remove all the d3d11 and dxgi header version dependent ifdef
and bump the minimum requirement to d3d11_4.h and dxgi1_6.h.
We are already failing support old Visual Studio (Windows SDK actually)
such as Visual Studio 2015. Note that our MinGW toolchain satisfies
the requirement.
From runtime point of view, this change should be fine since
we are checking OS version with IUnknown::QueryInterface()
everywhere in order to check API availability
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1684>
We make all MSDK encoders declare "memory:VAMemory" feature. Then
the pipeline such as:
gst-launch-1.0 -vf filesrc location=xxx.h264 ! h264parse ! \
vah264dec ! msdkh265enc ! fakesink
will choose VA memory caps between the VA decoder and MSDK encoder.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1087>
The MSDK encoder's query function is not set and it just forwards
all query to its base class. We now need to answer the context
query correctly. Other VA plugins need to query the VA display.
By the way, the current query of "gst.msdk.Context" is also missing.
The other MSDK elements must depend on the bin's context message(
sent in context_propagate()) to set their MsdkContext correctly.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1087>
The MSDK VPP's query function is not set and it just forwards
all query to its base class. We now need to answer the context
query correctly. Other VA plugins need to query the VA display.
By the way, the current query of "gst.msdk.Context" is also missing.
The other MSDK elements must depend on the bin's context message(
sent in context_propagate()) to set their MsdkContext correctly.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1087>
The MSDK decoder's query function is not set and it just forwards
all query to its base class. We now need to answer the context
query correctly. Other VA plugins need to query the VA display.
By the way, the current query of "gst.msdk.Context" is also missing.
The other MSDK elements must depend on the bin's context message(
sent in context_propagate()) to set their MsdkContext correctly.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1087>
We now can use the gst va lib's display to create our MSDK context,
and use its helper functions to simplify our code. The improved logic
is like this:
1. Every MSDK element should use gst_msdk_context_find() to find a MSDK
context from neighbour. If valid, reuse it.
2. Use gst_msdk_ensure_new_context(). It will first query neighbours
about the GstVaDisplay, if found(e.g. some VA element is connected),
use gst_msdk_context_from_external_display() to create a MSDK context.
3. Then, creating the MSDK context from scratch. It creates both the
display and MSDK context.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1087>
The VA display object from VA lib is a common defined object. which
contain the whole display things. It is easier to use, and more important,
we can share it with the other VA plugins and keep all the VA related
plugins working on the same GPU device.
We also delete the useless gst_msdk_context_get_fd() API.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1087>
The current manner for deciding the new temporal unit is based on
temporal delimiter(TD) OBU. We only start a new temporal unit when
the TD comes.
But some streams do not have TD at all, which makes the output "TU"
alignment fail to work. We now add check based on the relationship
between the different layers and it can successfully judge the TU edge.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1634>
Some streams may have problematic OBUs at the beginning, which causes
the parse fail to detect the alignment and return error. For example,
there may be verbose OBUs before a valid sequence, which should be
discarded until we meet a valid sequence. We should let the parse
continue when we meet such cases, rather than just return error.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1634>
Our D3D11/DXVA codecs implementation has been verified
during 1.18 and 1.20 development cycle and also via the Fluster
test framework. Similar to the case of nvdec and vtdec,
we can prefer hardware over software in most cases
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1672>
For artificial input (in unit tests), all six bytes of
constraint_indicator_flags in hevc_caps_get_mime_codec() can be
zero. Add a guard against an out-of-bounds error that occurred in that
case. Change variables to signed int so comparison with -1 works.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1677>
Duplicating a picture what was already a dup was leading to a crash. Rename
the custom picture flags as HOLDS_BUFFER to make its meaning clear. Then save
then ref and store the picture as userdata, so it can be obtained when
duplicating. Finally, mark the doplicated as HOLDS_BUFFER to avoid thinking it
holds a request.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1681>
This patch adds a new parameter: hdr-tone-mapping (same as
vaapipostproc), if the HDR capabilites are availabe in driver, and
it's disabled by default.
If hdr-tone-mapping is enabled then HDR fields in sink caps are
processed in frames from HDR to SDR, removing those hdr fields in
source pad caps too.
hdr-tone-mapping is not enabled if a color conversion is also
requested, since it fails to process in the iHD driver, so far.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1258>
1. Use api_version variable rather than static string.
2. Remove pkgconfig generation since currently the library
is not installed, only used internally.
3. Rely on dependency "required" to abort compilation.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1650>
In commit e699aaeb we moved linking of libgudev to the plugin rather
the library, because it's only used in the plugin. But the dependency
check is still done in library.
This patch removes the dependency check in library, and updates the
dependency check in plugin.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1650>
Constantly updating the ts_offset results in audiable glitches
when streaming audio using ntp-sync=true. By requiring a minimum
offset before updating ts_offset this can be mitigated. Added a
parameter which can be used to set min_ts_offset in ntp-sync mode.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1409>
A new implementation of Intel Quick Sync Video plugin.
This plugin supports both Windows and Linux but optimization for
VA/DMABuf is not implemented yet.
This new plugin has some notable differences compared with existing
MSDK plugin.
* Encoder will expose formats which can be natively supported
without internal conversion. This will make encoder
control/negotiation flow much simpler and cleaner than
that of MSDK plugin.
* This plugin includes QSV specific library loading helper,
called dispatcher, with QSV SDK headers as a part of this plugin.
So, there will be no more SDK version dependent #ifdef in the code
and also there will be no more build-time MSDK/oneVPL SDK
dependency.
* Memory allocator interop between GStreamer and QSV is re-designed
and decoupled. Instead of implementing QSV specific allocator/bufferpool,
this plugin will make use of generic GStreamer memory
allocator/bufferpool (e.g., GstD3D11Allocator and GstD3D11BufferPool).
Specifically, GstQsvAllocator object will help interop between
GstMemory and mfxFrameAllocator memory abstraction layers.
Note that because of the design decision, VA/DMABuf support is not made
as a part of this initial commit. We can add the optimization for Linux
later once GstVA library exposes allocator/bufferpool implementation as
an API like GstD3D11.
* Initial encoder implementation supports interop with GstD3D11
infrastructure, including zero-copy encoding with upstream D3D11 element.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1408>
There's no need to do this, and it can make seeking far less accurate.
For a specific use case: I am working with a long (45-minute) MPEG-1 layer 3 file, which has a constant bit rate but no seeking tables. Trying to seek the pipeline immediately after pausing it, without the ACCURATE flag, to a location 41 minutes in, yields a location that is potentially over ten seconds ahead of where it should be. This patch improves that drastically.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/374>
During dispose the pool will still have a reference count of 1 and all
API on it can still be safely called.
Subclasses will have already freed their own data before finalize is
called but would nonetheless be called into again via the pool
deactivation.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1645>
It's almost pointless and makes little sense as subclass might
want to modify refcount of the object or so. And all subclasses
are already casting them to non-const version as well.
In a general sense, we need to avoid passing refcounted object
with const qualifier.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1238>
... in order to make older g-i happy (~1.60) which doesn't like
freeform descriptions in the value_name field. Which in turn
then makes hotdoc happy instead of erroring out when we bump
the symbol index version.
We usually only (ab)use the name field for description strings
for private plugin enums, not for public API visible to bindings.
This lets glib-mkenum generate the _get_type() function for the
enum again, which in turn will generate the expected value names
to match the enums.
We might be able to add this back later once we can upgrade the
g-i version requirement (and the documentation job image).
This reverts most of commit b0aab48cdcf0a454d14aeb4d907209d8ee3f1add
There's a race condition in gsttagdemux.c between typefinding and the
end-of-stream event. If TYPE_FIND_MAX_SIZE is exceeded,
demux->priv->collect is set to NULL and an error is returned. However,
the end-of-stream event causes one last attempt at typefinding to occur.
This leads to gst_tag_demux_trim_buffer() being called with the NULL
demux->priv->collect buffer which it attempts to dereference, resulting
in a segfault.
The malicious MP3 can be created by:
printf "\x49\x44\x33\x04\x00\x00\x00\x00\x00\x00%s", \
"$(dd if=/dev/urandom bs=1K count=200)" > malicious.mp3
This creates a valid ID3 header which gets us as far as typefinding. The
crash can then be reproduced with the following pipeline:
gst-launch-1.0 -e filesrc location=malicious.mp3 ! queue ! decodebin ! audioconvert ! vorbisenc ! oggmux ! filesink location=malicious.ogg
Fixes https://gitlab.freedesktop.org/gstreamer/gstreamer/-/issues/967
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1620>
The kCVPixelFormatType_64RGBALE enum is only available on macOS Big
Sur (11.3) and newer. We also cannot use that while configuring the
encoder or decoder on older macOS.
Define the symbol unconditionally, but only use it when we're running
on Big Sur with __builtin_available().
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1613>
Hotdoc should be able to extract and parse comments out of these. Just
need to be careful to only add the glob in directories that actually
contain *.m (objc) and *.mm (objcpp) files.
Also fix some doc comments and remove redundant ones.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1614>
Platform wise, is not possible, as far as I known, to have Wayland
without kernel's DRM. Though, it's possible to configure
gstreamer-vaapi without DRM but Wayland support, with the enhanced
handling of dmabuf in vaapisink for Wayland, vaapisink will always
fail. Given both issues, configuration with no DRM but Wayland, makes
things more complex, and a simpler approach is to refuse that
configuration.
This patch disables Wayland support if there isn't DRM support. Also,
it disables the display test for Wayland, relying only on DRM and
X11.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1606>
Formats map is instantiated at the end of the display
instantiation. The problem is the Wayland display which looks for a
format in a callback, before the map is populated.
If user compiles gstreamer-vaapi with DRM support, the map is
populated with a DRM display at GStreamer plugin registration. But if
not, or a VA driver is not available, the plugin will try with a
Wayland driver, which cause the NULL de-reference.
Nevertheless, in the case of no DRM support, and if the Wayland
display doesn't get a reply from the format conversion is not a
problem.
So the solution is the trivial one, check if the format map is already
populated before de-reference it.
Fixes: #977
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1606>
This is listed as a public interface implemented by osxaudio, so we
need to mark it as a plugin API so that it's listed in the
documentation correctly.
This is an ancient symbol, so add it to the symbol index too.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1601>
These symbols from macOS plugins osxaudio, osxvideo, and applemedia
have been present for a very long time but were never documented.
This allows us to document these, and also add Since: markers for new
features (symbols) there were added in 1.20
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1601>
This moves the ABI check to the registration, so we don't expose
decoders with the wrong ABI or that are just broken somehow. It
also makes few enhancement:
- Handle missing, but required controls
- Prints the controls macro name instead of id
This should fix RK3399 support with a currently release minor
regression in the Hantro driver that cause errors.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1599>
... in addition to all the other issues that were ignored for them
already.
At least the reverse playback test regularly times out, waiting for a
download to finish that has already finished successfully.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1593>
Starting with libsoup3, there is no attempt to handle thread safety
inside the library, and it was never considered fully safe before
either. Therefore, move all session handling into its own thread.
The libsoup thread has its own context and main loop. When some
request is made or a response needs to be read, an idle source
is created to issue that; the gstreamer thread issuing that waits
for that to be complete. There is a per-src condition variable to
deal with that.
Since the thread/loop needs to be longer-lived than the soup
session itself, a wrapper object is provided to contain them. The
soup session only has a single reference, owned by the wrapper
object.
It is no longer possible to force an external session, since this
does not seem to be used anywhere within gstreamer and would be
tricky to implement; this is because one would not have to provide
just a session, but also the complete thread arrangement made in
the same way as the system currently does internally, in order to
be safe.
Messages are still built gstreamer-side. It is safe to do so until
the message is sent on the session. Headers are also processed on
the gstreamer side, which should likewise be safe.
All requests as well as reads on the libsoup thread are issued
asynchronously. That allows libsoup to schedule things with as
little blocking as possible, and means that concurrent access
to the session is possible, when sharing the session.
Fixes https://gitlab.freedesktop.org/gstreamer/gstreamer/-/issues/947
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1555>
Intel drivers expose some colorbalance's maximum values much more
bigger than their minimum values, given their middle values (default
value). This means, in practice, that the real middle point between
the maximum and minimum values implies a major change in the color
balance, which is not expected by the GStreamer color balance logic.
This patch makes the given maximum value symmetrical to the minimum
value, given the middle one (default value).
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1580>
It was getting pulled in automatically via cairo, but the version
there is too old for us. We need the latest to fix Windows ARM64 NEON
support:
> ERROR: No specified compiler can handle file subprojects\libpng-1.6.37\arm/filter_neon.S
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1570>
As now, we warn if the decoder have no support src pixel format, but that
warning is called before the type (hence the debug category) is initialized.
Fix this by moving the debug category init out of the type initialization,
into the register funcitons.
This will fix an assertion that occures in the register function and allow
relevant log to be seen by the users.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1588>
Those will cause us to renegotiate at the next aggregate cycle,
and while at that point we may decide to reconfigure upstream
branches (in practice we don't as this is inherently racy,
and that's the reason why mixer subclasses perform conversion
internally), we certainly don't want to just forward the event
willy-nilly to all our sinkpads.
An actual issue this is fixing is when caps downstream of a
compositor are changed at every samples-selected signal emission,
for the purpose of interpolating the output geometry, and the
compositor has a non-zero latency, the reconfigure events were
forwarded to basesrc, which triggered an allocation query, which
in turn caused aggregator to have to drain (thus not being able
to queue <latency> frames), leading to disastrous effects
(choppy output as compositor couldn't consume frames fast enough,
the higher the latency the choppier the output)
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1464>
The merge request workflow can be confusing to people unfamiliar with
it, so add screenshots.
Also add a new section on how to revise merge requests, since a lot of
people tend to open new merge requests to make any changes.
Eliminate the separate "How to Prepare a Merge Request for Submission"
section -- merge it with the main section.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1367>
This is usually necessary to allow gst-indent to treat it as
a statement, but we do not run gst-indent on headers and we do not
have extra semicolons in other places that this macro is used in the
header. Fixes warnings when using the header:
```
In file included from gstreamer/subprojects/gst-plugins-base/gst-libs/gst/video/video.h:185,
from XYZ:9001:
gstreamer/subprojects/gst-plugins-base/gst-libs/gst/video/gstvideoaggregator.h:206:78: warning: ISO C does not allow extra ‘;’ outside of a function [-Wpedantic]
206 | G_DEFINE_AUTOPTR_CLEANUP_FUNC(GstVideoAggregatorConvertPad, gst_object_unref);
| ^
gstreamer/subprojects/gst-plugins-base/gst-libs/gst/video/gstvideoaggregator.h:214:181: warning: ISO C does not allow extra ‘;’ outside of a function [-Wpedantic]
214 | G_DECLARE_DERIVABLE_TYPE (GstVideoAggregatorParallelConvertPad, gst_video_aggregator_parallel_convert_pad, GST, VIDEO_AGGREGATOR_PARALLEL_CONVERT_PAD, GstVideoAggregatorConvertPad);
| ^
```
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1572>
When fixating color, there might be "other caps" with color spaces not
supported by the caps features exposed in the vapostproc's source pad
caps template (perhaps it's a bug somewhere else in GStreamer).
This solution checks if the proposed format exists in the filter
within the caps feature associated with the proposed format.
The check is done with the new filter's function
gst_va_filter_has_video_format().
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1559>
In the need-data appsrc callback, a buffer is pulled from the
appsink. This buffer is then copied so that metadata is writable.
The copy is pushed to the appsrc but it doesn't take ownership
of the buffer so we need to manually unref it. The original buffer
is finally unreffed when the sample is freed.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1548>
This is due to an unsafe usage of the pad task. We didn't ensure proper
ownership of the task. That race involved the task being released too early,
and was detected, luckily, by the glib mutex implementationt that
reported the mutex being disposed while being locked.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1478>
On Android (especially) and for static builds in general it is safer to link
against libsoup and have the dynamic custom loading disabled. For those cases we
can safely assume the application will use either libsoup2 or libsoup3 and not
both.
Fixes#939
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1536>
The earlier size of 2 MB was set back in 2009, it doesn't
seem unreasonable to raise it to 8 MB these days. The use
case at hand is matroskademux containing both a video stream
with a very low amount of compression but no decoding latency,
and a H265 stream.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1538>
It is an extremely common mistake on Windows to have incorrect PATH
values when loading a plugin, and the error from g_module_error()
(which just calls FormatMessageW()) is very confusing in this case:
The specified module could not be found.
https://docs.microsoft.com/en-us/windows/win32/debug/system-error-codes--0-499-#ERROR_MOD_NOT_FOUND
It implies the plugin itself could not be found. The actual issue is
that a DLL dependency could not be found. We need to detect this case
and print a more useful error message.
We should still print the error fetched from FormatMessage() so that
people are able to google for it.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1540>
GstAudioRingBufferSpec::segsize has been configured by using
device period but GstWasapi2RingBuffer was referencing the
buffer size returned by IAudioClient::GetBufferSize()
which is most likely larger than device period.
Fixing to sync them.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1533>
If the `area_surface` got unmapped when changing to the `READY` or
`NULL` state, we currently don't remap it when playback resumes and
`wp_viewporter` is supported. Without `wp_viewporter` we do remap
it, but rather unintentionally and also when not wanted.
On Weston this has not been a big problem as it so far wrongly maps
subsurfaces of unmapped surfaces anyway - i.e. only the black
background was missing on resume. On other compositors and future
Weston this prevents the `video_surface` to get remapped.
Shuffle things around to ensure `area_surface` is mapped in the
right situations and do some minor cleanup.
See also https://gitlab.freedesktop.org/wayland/weston/-/issues/426
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1483>
Latest ffmpeg has removed avcodec_get_context_defaults(), and its
documentation says a new AVCodecContext should be allocated for this
purpose. The pointer returned by avcodec_find_decoder() is now
const-qualified so we also need to adjust for it. And, AVCOL_RANGE_MPEG
is now rejected with strict_std_compliance > FF_COMPLIANCE_UNOFFICIAL.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1531>
The later, doing damage in surface coordinates instead of buffer
coordinates, has been deprecated. The reason for that is that it
is more prone to bugs, both on the client and the compositor side,
especially when paired with buffer scale, `wp_viewporter` or
buffer transforms.
Unfortunately, on Weston this risks running into
https://gitlab.freedesktop.org/wayland/weston/-/issues/446
(which causes trouble for several other projects as well). However,
that bug only affects cases where we run in sync mode, i.e. only
during resizes. In practise I haven't been able to observe the
issue.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1446>
Each time we call `wl_surface_damage()` we want to do full surface
damage. Like Mesa, just use `G_MAXINT32` to ensure we always do
full damage, reducing the need to track the right dimensions.
`window->video_rectangle` is now unused, but we keep it around for
now as we may need it again in the future.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1446>
From the spec:
> This request is used to describe the regions where the pending
> buffer is different from the current surface contents
We currently also call `wl_surface_damage()` on surfaces without
new or still compositor-hold buffers, e.g. when resizing the window.
In that case we call it on `area_surface_wrapper`, even though it
gets resized via `wp_viewport_set_destination()`, in which case
the compositor is in charge of repainting the area on screen.
Doing so is currently not forbidden by the spec, however it might
be in the future, see
https://gitlab.freedesktop.org/wayland/wayland/-/issues/267
Thus lets stay close to the spec and only call `wl_surface_damage()`
when we just attached a buffer.
Right now this prevents runtime assertions in Mutter.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1446>
`gst_wl_window_set_opaque` does not get called on window resizes,
potentially leaving opaque regions too small.
According to the spec opaque regions can be bigger than the surface
size - parts that fall outside of the surface will get ignored.
Thus we can can simply use `G_MAXINT32` and be sure that the whole
surfaces will always be covered.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1446>
If the VANC track does contain packets, but we skip over all packets, just
treat it the same as if there hadn't been any packets at all and send a
GAP event instead of erroring out with "Failed to handle essence element".
We would error out because when we reach the end of the loop without having
found a closed caption packet the flow return variable is still FLOW_ERROR
which is what it has been initialised to.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1518>
Though the profiles[0] is inited as GST_H265_PROFILE_INVALID in the
gst_h265_profile_tier_level_get_profile(), the profile detecting may
change its content later. So the return of profiles[0] may not be an
invalid profile even the len is 0.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1517>
The previous code was mistakenly trying to compute a cc_type out
of the first byte in the byte triplet, whereas it is to be interpreted
as:
> Bit b7 of the LINE value is the field number (0 for field 2; 1 for field 1).
> Bits b6 and b5 are 0. Bits b4-b0 form a 5-bit unsigned integer which
> represents the offset
The same mistake was made when creating padding packets.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1496>
Sometimes we can't output anything because we don't have enough
incoming frames. In that case, the resampler was trying to call
do_quantize() and do_resample() in a loop forever because there would
never be samples to output (so chain->samples would always be NULL).
Fix this by not calling chain->make_func() in a loop -- seems
completely unnecessary since calling it over and over won't change
anything if the make_func() can't output samples.
Also add some checks for the input and / or output being NULL when
doing conversion or quantization. This will happen when we have
nothing to output.
We can't bail early, because we need resampler->samples_avail to be
updated in gst_audio_resampler_resample(), so we must call that and
no-op everything along the way.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1461>
When the image is opaque but the output ProRes format has an alpha
component (4 component, 32 bits per pixel), Apple requires that we
signal that it should be ignored by setting the depth to 24 bits per
pixel. Not doing so causes the encoded files to fail validation.
So we set that in the caps and qtmux sets the depth value in the
container, which will be read by demuxers so that decoders can skip
those bytes entirely. qtdemux does this, but vtdec does not use this
information at present.
The sister change was made in qtmux and qtdemux in:
https://gitlab.freedesktop.org/gstreamer/gst-plugins-good/-/merge_requests/1061
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1489>
Old "application/*" are now as per RFC8081 deprecated in favor of
new "font/*" mime types. Some new encoders are already using the
updated mime types. We need to also add them to the support list
in order for assrender to correctly identify them as fonts.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1481>
If there is no jitterbuffer stats we should not attempt to store them in the
global stats structure.
Also add a g_return_if_fail in _gst_structure_take_structure() about this
because it is a programmer error to pass an invalid pointer address there.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1479>
Add gst_dep to gst_rtsp_server_deps, in the context of buildroot, this
will avoid the following build failure, because the correct girdir
location will be retrieved from gstreamer-1.0.pc:
/home/giuliobenetti/autobuild/run/instance-3/output-1/host/riscv32-buildroot-linux-gnu/sysroot/usr/bin/g-ir-compiler gst/rtsp-server/GstRtspServer-1.0.gir --output gst/rtsp-server/GstRtspServer-1.0.typelib --includedir=/usr/share/gir-1.0
Could not find GIR file 'Gst-1.0.gir'; check XDG_DATA_DIRS or use --includedir
error parsing file gst/rtsp-server/GstRtspServer-1.0.gir: Failed to parse included gir Gst-1.0
If the above error message is about missing .so libraries, then setting up GIR_EXTRA_LIBS_PATH in the .mk file should help.
Typically like this: PKG_MAKE_ENV += GIR_EXTRA_LIBS_PATH="$(@D)/.libs"
Fixes:
- http://autobuild.buildroot.org/results/04af6b22cfa0cffb6a3109a3b32b27137ad2e0b0
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1460>
Prior to this patch, we considered that a stream was blocking
whenever a pad probe was triggered for either the RTP pad or
the RTCP pad.
This led to situations where we subsequently unblocked and expected
to find a segment on the RTP pad, which was racy.
Instead, we now only consider that the stream is blocking when
the pad probe for the RTP pad has triggered with a blockable object
(buffer, buffer list, gap event).
The RTCP pad is simply blocked without affecting the state of the
stream otherwise.
Fixes#929
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1452>
Instead of a sequence of if statements, declare a table to map profile
idc with profiles and traverse it.
Also, first add the profile from the parsed profile idc and later add,
into the profile array, the profile from the compatibility flags.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1440>
It's possible a HEVC stream to have multiple profiles given the
compatibility bits. Instead of returning a single profile, internal
gst_h265_profile_tier_level_get_profiles() returns an array with all
it possible profiles.
Profiles are appended into the array only if the generated profile
is not invalid.
gst_h265_profile_tier_level_get_profile() is rewritten in terms of
gst_h265_profile_tier_level_get_profiles(), returning the first
profile found the array.
And gst_h265_get_profile_from_sps() is also rewritten in terms of
gst_h265_profile_tier_level_get_profiles(), but traversing the array
verifying if the proposed profile is actually valid by Annex A.3.x of
the specification.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1440>
BT.2020 color primaries are designed to cover much wider range of
CIE chromaticity than BT.709, and also it's used for both SDR and HDR
contents. So, the incorrect assumption (i.e., BT.709 as a BT.2020)
is risky and resulting image color tends to be visually very wrong.
Unless there's obvious clue, don't consider color space of high resolution
video stream as BT.2020
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1445>
* Add fec / red encoders as direct children of webrtcbin, instead
of providing them to rtpbin through the request-fec-encoder signal.
That is because they need to be placed before the rtpfunnel, which
is placed upstream of rtpbin.
* Update configuration of red decoders to set a list of RED payloads
on them, instead of setting the pt property.
That is because there may be one RED pt per media in the same session.
* Connect to request-fec-decoder-full instead of request-fec-decoder,
in order to instantiate FEC decoders according to the payload type
of the stream.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1429>
When multiple streams are bundled together, there may be more
than one red payload type to handle.
In addition, as the red decoder works by filling in gaps in
the seqnums, there needs to be one rtp_history queue per sequence
domain.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1429>
In redenc, when input buffers have a header for the TWCC extension,
we now add one to our wrapper buffers.
In ulpfecenc we add one in that case to our protection buffers.
This makes TWCC functional when UlpRed is used in webrtcbin.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1414>
In order to allow "level-asymmetry-allowed" we now handle a new
"profile" field, which as the same semantics as the "profile" field in
H.264 stream so that we can force payloaded stream to have the right
format when using the `gst_sdp_media_get_caps_from_media` to set caps
filter after the payloader. This allows a simple negotiation in standard
RTP negotiation based on SDPs (like webrtc) for that particular case,
closely respecting the specs.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1410>
The ["level-asymmetry-allowed"] field states that the peer wants the
profile specified in the "profile-level-id" fields but doesn't care
about the level. To express this in GStreamer caps term, we add a
"profile" field in the caps, which reuses the usual "profile" semantics
for H.264 streams and, and remove "profile-level-id" and
"level-asymmetry-allowed" fields.
["level-asymmetry-allowed"]: https://www.iana.org/assignments/media-types/video/H264
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1410>
We are querying supported swapchain colorspace via
CheckColorSpaceSupport() but it doesn't seem to be reliable.
Use only tested full-range RGB formats which are:
- sRGB
- BT709 primaries with linear RGB
- BT2020 primaries with PQ gamma
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1433>
When using playbin3, it seems that the alpha decode is always first to
push caps and run an allocation query. As the format change from sink
and alpha were not synchronized, the allocation query could endup
being run before the caps are pushed. That may lead to failing query,
which makes the decoder thinks there is no GstVideoMeta downstream and
most likely CPU copy the frame.
This patch implements a format cookie to track and synchronize the
format changes on both pads fixing the racy performance issue.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1439>
This adds the alignment field to the template caps. Without this field
set, the auto-plugger will see fixed caps and will use
gst_caps_is_subset() against the caps produced by the parser. This is a
challenge for all cases where a parser can do conversion. This is fixed
by adding alignment field, which makes the auto-pluggers do an
intersection of the caps as it gets unfixed caps after intersection now.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1439>
XNextEvent() blocks indefinitely in absence of X11 events, which can
prevent the pipeline from stopping.
This can cause problems when ximagesrc is used in "remote desktop"
scenarios and the GStreamer application itself, through which the user
is viewing and controlling the machine, is the only source of input
events.
Replace the call with non-blocking XCheckTypedEvent().
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1438>
since `gst_caps_replace()` and `gst_pad_set_caps()` both ref the caps and neither of them takes the ownership of the caps -> it must be unreffed in `gst_multi_file_src_set_property()`
to test the leak (on Unix): `echo coucou > /tmp/file.txt && GST_TRACERS=leaks GST_DEBUG="GST_TRACER:7" gst-launch-1.0 multifilesrc location=/tmp/file.txt caps='txt' ! fakesink`
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1436>
When detecting the remote time has been reset which may occur if remote
device providing the clock server has been power reset, then clock is
no longer synced. Setting clock state will trigger a signal to client
informing on sync lost making it possibility to take appropriate action.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/975>
Due to a copy paste bug, the bitdepth was never set and that was leading
to requesting sizeimage of 0. Previously that worked since the driver
would in that case pick a size for us. But now the we bumped the minimum
to 4KB, the driver happily allocate 4KB of bitstream which lead to
decoding error.
As MPEG2 have a fixed bitdeph of 8, use a define instead of the run-time
variable.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1415>
vaapidecode is used in vaapidecodebin and it exposes all the
theoretically supported caps, but that slows down autoplug. With this
autplug is negotiated faster, giving more option to decodebin to select
other decoder.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1405>
The V4L2 uAPI uses pic_num for both PicNum and ShortTermPicNum. It also
doe the same for both FrameNum and LongTermFrameIdx. This change does
not change the fluster score, but fixed a visual corruption noticed
with some third party streams.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1387>
The current code does not set the copied memory correctly when it is popped
from the surface cache pool.
1. We forget to ref the allocator, which causes the allocator to be freed
unexpected, and we get a crash later because of the memory violation.
2. We forget to add ref_mems_count, which causes the surface leak because
the surface can not be pushed back to the cache pool again.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1373>
Set minimum sizeimage such that there is enough space for any overhead
introduced by the codec.
Notably fix a vp9 issue in which a small image would not have a
bitstream buffer large enough to accomodate it.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1012>
Rework gstvp9{decoder|statefulparser} to optionally parse compressed headers.
The information in these headers might be needed for accelerators
downstream, so optionally parse them if downstream requests it.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1012>
Also ignore 0x0 sizes in the fallback case and assume the size can be
anything between 1x1 and MAXxMAX.
This fixes the case where a width=0, height=0 caps are created. Whith
this patch the caps will contain width=[1,MAX], height=[1,MAX].
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1396>
When an extmap is defined twice for the same ID, firefox complains and
errors out (chrome is smart enough to accept strict duplicates).
To work around this, we deduplicate extmap attributes, and also error
out when a different extmap is defined for the same ID.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1383>
There are a lot of info in the mpeg2's sequence(also including ext
display_ext and scalable_ext). We need to notify the subclass about
its change, but not all the changes should trigger a drain(), which
may change the output picture order. For example, the matrix changes
in sequence header does not change the decoder context and so no need
to trigger a drain().
Fixes: #899
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1375>
Follow-up on 97d83056b3, only check
for intersection with the current srccaps when checking if a sinkpad
can accept caps.
I must have been lucky in my firefox testing then, and always entered
the code path with audio getting negotiated first, thus not failing
the is_subset check when srccaps had been negotiated as
application/x-rtp, and an accept-caps query was made for the video
caps with a defined extmap.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1384>
This is a requirement for GstPlayer when using the default overlay interface
provided by the pipeline. The GstPlayerWrappedVideoRenderer requires a valid
pipeline, but that's available only after the GstPlay thread has successfully
started.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1345>
Dynamically registered elements (hardware element in most cases)
may or may not be available on a system and properties may be different
per system.
This new API will make documentation skipping possible in programmable way.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1360>
ShowWindow() could be blocked while doing gst_d3d11_window_win32_unprepare
when external window handle provided to d3d11videosink in multi-threaded
environment.
The condition that issue happened is, UI thread is waiting for a
background thread that changes d3d11videosink state to NULL, and the
background thread would try to send a window message to the queue.
The queue is already occupied by the UI thread, so the background
thread will be blocked.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1366>
Instead of defining a sized array for function signature, use it
unsized (a pointer alias, basically). In this way clang warning is
silenced:
warning: ‘fill_profiles’ accessing 64 bytes in a region of size 12 [-Wstringop-overflow=]
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1357>
If qt asks us to redraw before we have both set a buffer and caps we
would attempt to use the new caps with the old buffer which could result
in bad things happening.
Only update caps from new_caps once the buffer has actually been set.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1346>
Make sure the EGLImage we're rendering to the GL memory stays alive long enough,
until the the GL memory has been destroyed.
This change fixes tearing and black flashes artefacts that were happening
because the EGLImage was sometimes destroyed before the sink actually rendered
the associated texture.
Fixes#889
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1354>
This takes a plain message string and not a format string, and as a
result doesn't have to be passed through vasprintf() and lead to further
unnecessary allocations. It can also contain literal `%` because of
that.
The new function is mostly useful for bindings that would have to pass a
full string to GStreamer anyway and would do formatting themselves with
language-specific functionality.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1356>
There's a potential race condition with this sort of pipelines on
certain systems (depends on the processing load):
GST_DEBUG_DUMP_DOT_DIR=/tmp \
gst-launch-1.0 uridecodebin3 uri=file://stream.mp4 ! glupload ! \
glimagesink --gst-debug=*:4
Right after the pipeline passes from PAUSED to READY, bin_to_dot_file
dumps uridecodebin3 properties, but current uri and suburi might be
already freed, causing a potential use-after-freed.
This patch makes NULL the current item right after all the play items
are freed.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1353>
A previous patch has caused rtpfunnel to output twcc-related
information downstream, however this leaked into upstream
negotiation (through funnel->srccaps), causing payloader to
negotiate twcc caps even when not prompted to do so by the user.
Fix this by only enforcing that upstream sends us application/x-rtp
caps as was the case originally.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1278>
Negative composition time offsets are only allowed with version 1 of the
box, however we parse it as a signed value also for version 0 boxes as
unfortunately there are such files out there and it's unlikely to have
(valid) huge composition offsets.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1294>
Sometimes the resampler has enough space to store all the incoming
samples without outputting anything. When this happens,
gst_audio_resampler_get_out_frames() returns 0.
In that case, the resampler should consume samples and just return.
Otherwise, we get a segfault when gst_audio_resampler_resample() tries
to resample into a NULL 'out' pointer.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1343>
g_sequence_remove_range's end iter is exclusive, so if one
wants to remove that item as well, it should be called with
the next iter.
This could in theory fix an issue where:
* The sequence isn't entirely trimmed, with an old item lingering
* Following FEC packets are immediately discarded because they
arrived later than corresponding media packets, long enough for
seqnums to wrap around
* We now try to reconstruct a media packet with a completely obsolete
FEC packet, chaos ensues.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1341>
We need to hold onto the last buffer until the next buffer arrives.
Before, if a caps change comes we would remove the currently rendering
buffer. if Qt asks use to render something, we would render the dummy
black texture.
Fixes a period of black output when upstream is e.g. changing resolution
as in hls adaptive bitrate scenarios.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1338>
The `gst_v4l2_buffer_pool_dqbuf` function contains this ominous comment:
/* get our GstBuffer with that index from the pool, if the buffer was
* outstanding we have a serious problem.
*/
outbuf = pool->buffers[group->buffer.index];
Unfortunately it is common for buffers in _output_ buffer pools to be
both queued and outstanding at the same time. This can happen if the
upstream element keeps a reference to the buffer, or in an encoder
element itself when it keeps a reference to the input buffer for each
frame.
Since the current code doesn't handle this case properly we can end up
with crashes in other elements such as:
(gst-launch-1.0:32559): CRITICAL **: 17:33:35.740: gst_video_frame_map_id: assertion 'GST_IS_BUFFER (buffer)' failed
and:
(gst-launch-1.0:231): GStreamer-CRITICAL **: 00:16:20.882: write map requested on non-writable buffer
Both these crashes are caused by a race condition related to releasing
the same buffer twice from two different threads. If a buffer is queued
and outstanding this situation is possible:
**Thread 1**
- Calls `gst_buffer_unref` decrementing the reference count to zero.
- The core GstBufferPool object marks the buffer non-outstanding.
- Calls the V4L2 release buffer function.
- If the buffer is _not_ queued:
- Release it back to the free pool (containing non-queued buffers).
**Thread 2**
- Dequeues the queued output buffer.
- Marks the buffer as not queued.
- If the buffer is _not_ outstanding:
- Calls the V4L2 release buffer function.
- Release it back to the free pool (containing non-queued buffers).
If both of these threads run at exactly the same time there is a small
window where the buffer is marked both not outstanding and not queued
but before it has been released. In this case the buffer will be freed
twice causing the above crashes.
Unfortunately the variable recording whether a buffer is outstanding is
part of the core `GstBuffer` object and is managed by `GstBufferPool` so
it's not as straightforward as adding a mutex. Instead we can fix this
by additionally recording the buffer state in `GstV4l2BufferPool`, and
handle "internal" and "external" buffer release separately so we can
detect when a buffer becomes not outstanding.
In the new solution:
- The "external" buffer pool release and the "dqbuf" functions
atomically update the buffer state and determine if a buffer is still
queued or outstanding.
- Subsequent code and a new
`gst_v4l2_buffer_pool_complete_release_buffer` function can proceed to
release (or not) a buffer knowing that it's not racing with another
thread.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1010>
The pipeline flow for receiving looks like this:
rtpsession ! rtpssrcdemux ! session_fec_decoder ! rtpjitterbuffer ! \
rtpptdemux ! stream_fec_decoder ! ...
There are two places where a fec decoder could be placed.
1. As requested from the 'request-fec-decoder' signal: after rtpptdemux
for each ssrc/pt produced
2. after rtpssrcdemux but before rtpjitterbuffer: added for the
rtpst2022-1-fecenc/dec elements,
However, there was some cross-contamination of the elements involved and
the request-fec-decoder signal was also being used to request the fec
decoder for the session_fec_decoder which would then be cached and
re-used for subsequent fec decoder requests. This would cause the same
element to be attempted to be linked to multiple elements in different
places in the pipeline. This would fail and cause all kinds of havoc
usually resulting in a not-linked error being returned upstream and an
error message being posted by the source.
Fix by not using the request-fec-decoder signal for requesting the
session_fec_decoder and instead solely rely on the added properties for
that case.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1300>
The average_period should always represent the time between two
events. The specification defines the event time as the time
between audio samples, video frame sync, video line sync, etc.
In case of one timestamp per PDU the timestamp_interval identifies
the amount of events between the timestamp of one PDU and the
timestamp of the next PDU.
As described in IEEE 1722-2016 chapter
"10.4.12 timestamp_interval field" timestamp_interval shall be
nonzero.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1076>
The failure conditions can be overidden by subclasses, and a boolean
return value is provided to the caller whether adding/removing the child
element has actually worked. The caller can then handle this
accordingly but flooding stderr with this is not very useful.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1320>
Upstream caps might for example be
application/x-rtp,media=audio,encoding-name={OPUS, X-GST-OPUS-DRAFT-SPITTKA-00, multiopus}
and while that is not fixed caps it is enough to match it with a media.
Only caps structures that have the correct structure name and that have
the media and encoding-name field are preserved, but if both are present
then these caps are used as "codec preferences".
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1291>
Currently reading extension relies on the fact that everything after the
last"." character is a file extension. Whereas that works fine for most
of the cases, it breaks when the URI contains a query part.
E.g.: `http://url.com/file.mp4?param=value` returns `mp4?param=value`
instead of `mp4`.
In this commit we use URI parser to read the path of the URI (in the example
above, that is `/file.mp4`) and read extension from that path.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1305>
Some decoding APIs support delayed output for performance reasons.
One example would be to request decoding for multiple frames and
then query for the oldest frame in the output queue.
This also increases throughput for transcoding and improves seek
performance when supported by the underlying backend.
Introduce support in the mpeg2 base class, so that backends that
support render delays can actually implement it.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1013>
Downstream might need the start code offset when decoding.
Previously this computation would be scattered in multiple sites. This
is error prone, so move it to the base class. Subclasses can access
slice->sc_offset directly without computing the address themselves
knowing that the size will also take the start code into account.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1013>
The GstV4l2CodecAllocator dispose function clears `self->decoder` but
the finalize function then tries to use it if the allocator has no been
detached yet.
Fix by detaching in the dispose function before we clear
`self->decoder`.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1220>
Standard interlace handling:
* If we have interlace-mode=interleaved and the field order, we just
set it when creating the session
* If we have interlace-mode=(interleaved|mixed) and no field order, we
set the field order on the first buffer
The encoder session does not support changing the FieldDetail after it
has started encoding frames, so we cannot support mixed streams
correctly.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1214>
Delay decoders downstream negotiation just before an output frame
needs to be allocated.
This is required, are least for H.264 and H.265 decoders, since
codec_data might trigger a new sequence before finishing upstream
negotiation, and sink pad caps need to set before setting source pad
caps, particularly to forward HDR fields. The other decoders are
changed too in order to keep the same structure among them.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1257>
Using GstBaseDec hack to access the parent_object of each element in
the element itself is a bit fragile. It would be better to keep its
own parent object as the usual global variable. It would make it
resistant to code changes.
The GstBaseDec macro to access the parent object now it's internal to
base decoder.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1257>
We were checking if the start time of the gap event was
GST_CLOCK_TIME_NONE, which is superfluous because that cannot happen,
and then not checking if it was NONE after gst_segment_to_running_time,
which caused a crash if an identity received a gap event fully or
partially outside the current segment.
This patch was done in cooperation with:
Jan Alexander Steffens (heftig) <jan.steffens@ltnglobal.com>
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1269>
.. if a current direction has already been set
When `webrtcbin` has created an offer based on codec_preferences,
it might not have received caps on its sinkpads by the time a
remote description is set, in which case we want to connect the
input stream upon actual reception of the caps instead.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1233>
With mpeg4videoparse drop=false config-interval=N|-1 we might be
trying to insert a config before we have actually received one,
in which case we'll try to map a NULL buffer which will generate
lots of criticals.
Fixes#855
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1265>
gst_va_fixate_format() will iterate all othercaps' structures to find
the one with less information lost at color conversion. If a structure
with same color format is found, the iteration stops. It's like a
smart truncation. Then, this function also will choose the caps
feature.
Later this structure is used fixate its size and no further truncation
is needed.
Don't intersect at fixate, since it kills possible resizing.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1261>
If the pad does not have a current caps, get_pad() returns the query
caps which can be ANY. In such case the caps does not have any structure
resulting in a critical warning when calling gst_caps_get_structure().
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1254>
Detected while reading the code, cccombiner must set
self->current_video_buffer to NULL *after* emitting selected-samples
in order for the application to get a useful return when peeking
the next video sample.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1252>
When schedule is true (as is the case by default), we insert padding
when no caption data is present in the schedule queue, and previously
weren't checking whether the caption pad had gone EOS, leading to
infinite scheduling of padding after EOS on the caption pad.
Rectify that by adding a "drain" parameter to dequeue_caption()
In addition, update the captions_and_eos test to push valid cc_data
in: without this cccombiner was attaching padding buffers it had
generated itself, and with that patch would now stop attaching
said padding to the second buffer. By pushing valid, non-padding
cc_data we ensure a caption buffer is indeed attached to the first
and second video buffers.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1252>
Also refactor various internals of the monitor code:
- Don't allow starting twice but just return directly when starting a
second time.
- Don't end up in an inconsistent state if call start() a second time
while the monitor is starting up.
- Remove complicated cookie code: it was not possible to add/remove
filters while the monitor was started anyway so this was only useful
in the very small time-window while starting the monitor or while
getting the devices. Instead disallow adding/removing filters while
the monitor is starting, and when getting devices work on a snapshot
of providers/filters.
Fixes https://gitlab.freedesktop.org/gstreamer/gstreamer/-/issues/667
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1189>
At gst_va_dmabuf_allocator_setup_buffer_full, static code analysis tool
does not know number of objects in descriptor is always larger than 0 if
export_surface_to_dmabuf succeeds. Thus, the tool will assume buf is
allocated with mem but not released when desc.num_objects equals to 0
and raise a mem leak issue.
For gst_va_dambuf_memories_setup, we should also inform the tool that
n_planes will be larger than 0 by checking the value at very beginning.
Then, the defect similar to above will not be raised during static analysis.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1241>
gst_base_parse_reset() does not reset data_bytecount to 0, so
gst_base_parse_update_bitrates() uses a wrong value to calculate
the average bitrate on subsequent pipeline starts. This leads to an
excessive amount of "tag" events being pushed. These events include
very high "bitrate" values that diminish over time, and are produced
until the average bitrate is back to sane values.
Fixes#840
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1228>
This will only affect individual/tarball module builds, as the
options yield to the parent project which was set to gpl=disabled
by default already. We kept it as auto in the original commit
to accommodate the need to update cerbero as well, which had to
be done separately after the initial commit.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1217>
Previously gst_structure_has_name was used to get a string to compare with supported mimetypes.
This is incorrect as above function returns a user defined structure name which is
not the structure mimetype value.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1206>
Trying to reset before the pads have been deactivated races with the
streaming thread. There was also a buggy buffer clear leaving a dangling
`stored_frame` pointer around. Use `gst_interlace_reset` so this happens
properly.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1039>
We don't support D3D11 interop for UWP because some APIs
(specifically MFTEnum2) are desktop application only.
However, the code for symbol loading is commonly used by both UWP and WIN32.
Just link GModule unconditionally which is UWP compatible, and simply don't
try to load any library/symbol dynamically when D3D11 interop is unavailable.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1216>
... in favour of dep.get_variable('foo', ..) which in some
cases allows for further cleanups in future since we can
extract variables from pkg-config dependencies as well as
internal dependencies using this mechanism.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1183>
When ass hinting value is set to anything other than NONE,
subtitles cannot use smooth scaling, thus all animations will jitter.
The libass author warns about possibility of breaking some scripts when it is enabled,
so lets do what is recommended and disable it to get the smooth scaling working.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1201>
WebVTT in ISO MP4 is specified in ISO 14496-30,
and needed for DASH support. It's stored in an
mp4 specific format. To handle it compatibly,
the wvtt boxes are converted back into WebVTT text
and pushed as application/x-subtitle-vtt
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1182>
Swap the `need_process` boolean check on qtdemux streams
for a direct function pointer to the splitting function,
so we can stop adding extra cases to the single growing
`gst_qtdemux_process_buffer()` function.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1182>
