librtmp allows for attaching arbitrary AMF objects to the end of the
connect packet, and this is commonly used for authenticating with
servers.
Add a new property, extra-connect-args, that mimics librtmp's behavior.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/7054>
A previous fix, a275e1e029, is correct but was too
permissive since it treats all un-matched NAL units the same as AU delimiters
even though some other NAL unit types can be encountered in the processing loop.
The problem this can cause is that some hardware decoders experience bad
performance when handling FD units that precede the SPS.
This change restores the original behavior for FDs so that they're ignored until
the SPS is received and it preserves the codec conformance test gains that the
fix has achieved.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/7166>
When configured in constant bitrate mode, the muxer computes timing information
using the configured bitrate and the byte counter (now = bytes sent / byterate).
When an application changes the bitrate in CBR mode during playback, the
relationship between bytes sent and bitrate is no longer valid so new timing
values will be off by the ratio of the old bitrate to the new bitrate.
Furthermore, it will upset the way that padding is generated.
pad_stream() works by trying to fit the byte counter to now * byterate.
The result is that when decreasing bitrate, the muxer stalls, waiting until the
byte counter is in agreement with now * byterate. Also, when increasing
bitrate, the padding will spike in volume until the byte counter fits with
now * byterate.
If the byte counter is scaled by the ratio of new bitrate / old bitrate when
adjusting bitrate, then padding is generated in a way that applications would
more likely expect.
One detail this change doesn't yet address is whether the next PCR will match up
optimally with the previous PCR right after the byte counter is scaled. In that
case, some correction may be necessary. Also, perhaps the user should be
prevented from changing from bitrate=0 to bitrate=nonzero during playback since
it's not straightforward how to scale the byte counter in that case.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/7158>
When transforming from unknown alignment to frame or obu, the TU timestamp
was not properly transferred. Fix this by saving the TU DTS as the first
DTS seen within the the TU data, and the PTS as the last PTS seen in that
TU data. Finally, reset the TU timestamp after each TU have completed.
Fixes#1496
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6895>
If the muxer times out because of the latency deadline it can happen
that some pads have no caps yet. In that case skip creation of streams
for these pads and create updated section tables once the first buffer
arrives later.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6823>
This makes sure that for sparse streams (KLV, DVB subtitles, ...) the
muxer does not wait until the next buffer is available for them but
times out on the latency deadline and outputs data.
For non-live pipelines it will still be necessary for upstream to
correctly produce gap events for sparse streams.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6823>
There was an issue with this equality check, which was to figure out what to do
with PCR pids (whether they were part of the streams present or not) and whether
we ignore PCR or not.
Turns out ... we already took care of that further up in the function.
The length check can be simplified by just checking whether the length of
the *original* PMT and the new PMT are identical. Since we don't store "magic"
PCR streams in those, we can just use them as-is.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6713>
The goal of this code was, for programs which were updates (i.e. adding/removing
streams but not completely changing) to allow dynamic addition/removal of
streams without completely removing everything.
But this wasn't 100% tested and there are a bunch of issues which make it fail
in plenty of ways.
For now disable that feature and force the legacy "add all pads again and then
remove old ones" behaviour to make it switch.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6651>
For some cameras `gst_jpeg_parse_app0()` fails on a invalid segment.
While this is likely a driver or firmware bug that should be addressed
accordingly, it's not fatal and likely does not deserve a bus message on
every frame, flooding journals.
Turn down the volume of the warnings by turning them into object
warnings. If we conclude that in some cases we'd still want bus
warnings, they can be done more fine-grained in the
`gst_jpeg_parse_appX()` functions.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6490>
In the situation where playback starts from a keyframe before
the target playback segment, then the first buffers will be
outside the configured segment and gst_segment_to_stream_time()
will return GST_CLOCK_TIME_NONE unconditionally.
If drop-out-of-segment is false, the RTP buffers will not be
dropped, but will be sent witout ONVIF extension timestamps
and given GST_CLOCK_TIME_NONE timestamps on the receiver.
Instead, use gst_segment_to_stream_time_full() to extrapolate
stream time outside the segment so that such buffers still
get assigned their correct timestamps on the receiver.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6248>
Don't accidentally include the stuffing byte (if present)
into the bottom field size. It should only be included in the
total segment length.
Fixes problems with FFmpeg not rendering the subtitles
with a stuffing byte, giving a "Invalid object location!" error.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6250>
