The minimum latency is the latency we have to wait at least
to guarantee that all upstreams have produced data. The maximum
latency has no meaning like that and shouldn't be used for waiting.
When iterating sink pads to collect some data, we should take the stream lock so
we don't get stale data and possibly deadlock because of that. This fixes
a definitive deadlock in _wait_and_check() that manifests with high max
latencies in a live pipeline, and fixes other possible race conditions.
This simplifies the code and also makes sure that we don't forget to check all
conditions for waiting.
Also fix a potential deadlock caused by not checking if we're actually still
running before starting to wait.
When this is TRUE, we really have to produce output. This happens
in live mixing mode when we have to output something for the current
time, no matter if we have enough input or not.
This removes the uses of GAsyncQueue and replaces it with explicit
GMutex, GCond and wakeup count which is used for the non-live case.
For live pipelines, the aggregator waits on the clock until either
data arrives on all sink pads or the expected output buffer time
arrives plus the timeout/latency at which time, the subclass
produces a buffer.
https://bugzilla.gnome.org/show_bug.cgi?id=741146
Otherwise the caps of the pad might change while the subclass still works with
a buffer of the old caps, assuming the the current pad caps apply to that
buffer. Which then leads to crashes and other nice effects.
https://bugzilla.gnome.org/show_bug.cgi?id=740376
Audiomixer blocksize, cant be 0, hence adjusting the minimum value to 1
timeout value of aggregator is defined with MAX of MAXINT64,
but it cannot cross G_MAXLONG * GST_SECOND - 1
Hence changed the max value of the same
https://bugzilla.gnome.org/show_bug.cgi?id=738845
Determines the amount of time that a pad will wait for a buffer before
being marked unresponsive.
Network sources may fail to produce buffers for an extended period of time,
currently causing the pipeline to stall possibly indefinitely, waiting for
these buffers to appear.
Subclasses should render unresponsive pads with either silence (audio), the
last (video) frame or what makes the most sense in the given context.
The previous implementation kept accumulating GSources,
slowing down the iteration and leaking memory.
Instead of trying to fix the main context flushing, replace
it with a GAsyncQueue which is simple to flush and has
less overhead.
https://bugzilla.gnome.org/show_bug.cgi?id=736782
Without a lock that is taken in FLUSH_START we had a rare race where we
end up aggregating a buffer that was before the whole FLUSH_START/STOP
dance. That could lead to very wrong behaviour in subclasses.
Avoiding to be in an inconsistent state where we do not have
actual negotiate caps set as srccaps and leading to point where we
try to unref ->srccaps when they have already been set to NULL.
https://bugzilla.gnome.org/show_bug.cgi?id=735042
Along with the required mandatory dependent events.
Some elements need to perform an allocation query inside
::negotiated_caps(). Without the caps event being sent prior,
downstream elements will be unable to answer and will return
an error.
https://bugzilla.gnome.org/show_bug.cgi?id=732662
The gst_ptp_clock_new() does not actually require a name. However, for
example the rtpjitterbuffer may create a clock without a name, fail, and
fall back to not using the PTP clock.
https://bugzilla.gnome.org/show_bug.cgi?id=791034
Fixes in user code:
undefined reference to `gst_harness_add_element_sink_pad'
Also reorder harness function list to be strictly in alphabetical order and
double check the list with:
awk '{ if ($1 !~ /#define/) if ($2 ~ /gst_harness_/) { print $2 }; if ($3 ~ /gst_harness_/) { print $3} }' libs/gst/check/gstharness.h | sort
There were a few errors:
* The plugin scanner now accepts executable path as an argument.
In case it is NULL, argc == 2
* We find the executable path in init_pre instead of gst_init,
allowing this to work when gst is initialized through the
option group (eg gst-inspect)
* There was a semi-colon missing in the __APPLE__ #ifdef
When a plugin declares a dependency using this flag, all the
relative paths are considered to be relative to the path of
the main executable.
We try to determine the path of the executable portably,
with implementations provided for Linux, Windows and Mac.
If retrieval of the path fails, we will not detect changes.
In order for the main executable path to be the same when
scanning a plugin in a child process, a new variable is
exposed in gst_private.h, _gst_executable_path
https://bugzilla.gnome.org/show_bug.cgi?id=788152
We would constantly re-post the taglist because
posted_avg_rate only gets set to avg_bitrate if
parse->priv->post_avg_bitrate is true, so if it's
false the posted rate will always differ from the
current average rate and we'd queue an update,
which leads to us spamming downstream and the
application with taglist updates.
Fix this by only queuing an update if the average
rate will actually be posted.
These taglists updates could cause expensive
operations on the application side, e.g. in Totem.
https://bugzilla.gnome.org/show_bug.cgi?id=786561
Need to define CK_DLL_EXP to extern as well in libcompat.h
which gets included before the internal-check.h where the
other fallback definition for CK_DLL_EXP is.
duplicate symbol _check_minor_version in:
libcheckinternal.a(libcheckinternal_la-check.o)
libcheckinternal.a(libcheckinternal_la-check_log.o)
Have to modify libcheck header a bit to avoid warnings
about duplicate 'extern extern'.
Also needs some additions to the libcheck meson.build file
to define CK_EXP_DLL when building the static libcheck.
buffer is not unreferened if preroll failed
:Detailed Notes:
- Problem : video freeze when switching from pause to 1/2-FF repeatedly
- RootCause : buffer leaks in basesink
- Solution : unref the buffer if prerolled failed
:Testing Preformed:
How to Test :
pause -> 1/2 FF -> resume -> pause -> 1/2 FF ...
https://bugzilla.gnome.org/show_bug.cgi?id=784932
Holding this lock on live source prevents the source from changing
the caps in ::create() without risking a deadlock. This has consequences
as the LIVE_LOCK was replacing the STREAM_LOCK in many situation. As a
side effect:
- We no longer need to unlock when doing play/pause as the LIVE_LOCK
isn't held. We then let the create() call finish, but will block if
the state have changed meanwhile. This has the benefit that
wait_preroll() calls in subclass is no longer needed.
- We no longer need to change the state to unlock, simplifying the
set_flushing() interface
- We need different handling for EOS depending if we are in push or pull
mode.
This patch also document the locking of each private class member and
the locking order.
https://bugzilla.gnome.org/show_bug.cgi?id=783301
This is something bindings can't handle and it causes leaks. Instead
move the ref_sink() to the explicit, new() constructors.
This means that abstract classes, and anything that can have subclasses,
will have to do ref_sink() in their new() function now. Specifically
this affects GstClock and GstControlSource.
https://bugzilla.gnome.org/show_bug.cgi?id=743062
gst_harness_new_parse() returns without any error even if it doesn't
find the specified element. Then a succeeding call to
gst_harness_set_sink_caps_str() causes an error like this:
Unexpected critical/warning: gst_pad_push_event: assertion 'GST_IS_PAD (pad)' failed
This is a bit cryptic and doesn't give users any clue what was going
on.
gst_harness_new_parse() calls gst_harness_add_parse() with a newly
created empty harness and the given pipeline description string, but
gst_harness_add_parse() does not have a way to propagate the error
back to the caller. Since the function, gst_harness_add_parse(), is a
public API, it's not a good idea to change its signature. This patch,
instead, makes the function to g_error() when it discovers any error.
With this change the same error prints:
** (myelement-test:25345): ERROR **: Unable to create pipeline 'bin.( myelement )': no element "myelement"
The current implementation of gst_parse_launch_full() doesn't return
partially constructed pipeline when GST_PARSE_FLAG_FATAL_ERRORS is
specified, however, this patch also adds a check for it.
https://bugzilla.gnome.org/show_bug.cgi?id=781958
An untested pointer segfaulted in webkit while playing video
on imx6 sabrelite. It turned out that the imx plugin didn't
implement the meta transform function.
The following GST_DEBUG trace was visible:
gstbasetransform.c:1779:foreach_metadata:<conv2> copy metadata
GstImxVpuBufferMetaAPI
Thread 26 vqueue:src received signal SIGSEGV, Segmentation fault.
(gdb) bt
0x00000000 in ?? ()
0x73f8d7d8 in foreach_metadata (inbuf=0xc9b020, meta=0x474b2490,
user_data=<optimized out>) at gstbasetransform.c:1781
0x73eb3ea8 in gst_buffer_foreach_meta (buffer=buffer@entry=0xc9b020,
func=0x73f8d705 <foreach_metadata>,
user_data=user_data@entry=0x474b24d4)
at gstbuffer.c:2234
https://bugzilla.gnome.org/show_bug.cgi?id=782050
This unbalanced closing parenthesis is leftover from the commit
8b739d91e7. It used to wrap the caps but we don't seem to do that in
the current code.
So, just remove it. No functionality has been changed.
https://bugzilla.gnome.org/show_bug.cgi?id=781484
Use g_object_new() instead which nowadays has a shortcut for the
no-properties check. It still does an extra GType check in the
function guard, but there's a pending patch to remove that
and it's hardly going to be a performance issue in practice,
even less so on a system that's compiled without run-time checks.
Alternative would be to move to the new g_object_new_properties()
with a fallback define for older glib versions, but it makes the
code look more unwieldy and doesn't seem worth it.
Fixes deprecation warnings when building against newer GLib versions.
https://bugzilla.gnome.org/show_bug.cgi?id=780903
This patch reorganize the bash completion scripts in order to install
the binary helper (gst-completion-helper) in libexec path rather then
share folder. Most Linux hierarchy compliance requires that no binary
executable are placed in share. We also cleanup the unused .pc entries
and remove copy pasted parts of the script. Note that other project
including the common helper, should now use $_GST_HELPER to read
the binary executable gst-completion-helper. This helper is not longer
version, as it is placed in a versionned subfolder
(libexec/gstreamer.10) just like the other helpers (scanner and ptp).
If parsing returns a non-OK flow return in the middle
of processing an input buffer, don't overwrite that
if a later return is OK again - the subclass might
return not-linked in the middle, and then discard
subsequent data without pushing while returning OK.
A later success doesn't invalidate the earlier failure,
but we should continue processing after not-linked, so
as to keep parse state consistent.
https://bugzilla.gnome.org/show_bug.cgi?id=779831
We would add the offset a second time in _scan_for_start_code()
when we found a result, but it's already been added to the data
pointer at the beginning of _masked_scan_uint32_peek(), so the
peeked value would be wrong if the initial offset was >0, and
we would potentially read memory out-of-bounds.
Add unit test for all of this.
https://bugzilla.gnome.org/show_bug.cgi?id=778365
Otherwise when seeking/looping to the start when reaching the end,
the sink waits for the duration of the stream. So the user hears
nothing for the duration of the stream before it actually loop again.
See example attached to the bug for that.
Existing test:
gst-plugins-good/tests/icles/test-segment-seeks foo.flac
Without the patch the user hears a crack/cut at each seek.
https://bugzilla.gnome.org/show_bug.cgi?id=777780
New API functions to filter log messages before they are processed by
GstCheck. This can be used to discard specific messages that are
accepted by the test or to add callbacks that test specific messages.
Default bevavior when no callback is given to a filter is to discard the
message, because it does not makes sense to have a filter with no
callback which does not discard; that would be a noop.
Discarded messages will in addition to bypass the GstCheck handling also
return to GLib that the message is not fatal if it occurs.
https://bugzilla.gnome.org/show_bug.cgi?id=773091
When malloc is not available, this will set #define malloc rpl_malloc
which is implemented only inside libcheck, and not everything will link
to libcheck.
We don't really need to care too much about how malloc is implemented
and we don't care about platforms that don't implement malloc.
This brings us up-to-speed with the latest compatibility code from upstream
check git. For completeness, we do all the checks that upstream check does, but
we skip the snprintf/vsnprintf code because it's not straightforward (involves
running code and that is bad for cross-compilation) and not necessary for the
platforms we support anyway.
If someone really wants this, they can uncomment this and copy the relevant
checks from the check git repository.
https://bugzilla.gnome.org/show_bug.cgi?id=775870
Makes it clearer which files are actually used in libcheck and which are used
for cross-platform compatibility. This is going to be especially useful when we
add all the libcompat fallback code that upstream libcheck has which will add
about 6 new files.
https://bugzilla.gnome.org/show_bug.cgi?id=775870
Upstream seems to have stopped doing releases, but we need to update for better
Windows and Visual Studio support.
This patch only updates the libcheck sources and ignores the compatibility
sources for now.
https://bugzilla.gnome.org/show_bug.cgi?id=775870
This was totally non-obvious, the kind of big problem is that subclasses must
be able to unblock their streaming thread and continue exactly where they left off
on unpause!
https://bugzilla.gnome.org/show_bug.cgi?id=773912
Allows proxying the control interface from one property on one GstObject
to another property (of the same type) in another GstObject.
E.g. in a parent-child relationship, one may need to
gst_object_sync_values() on the child and have a binding (set elsewhere)
on the parent update the value.
Note: that this doesn't solve GObject property forwarding and must be
taken care of by the implementation manually or using GBinding.
https://bugzilla.gnome.org/show_bug.cgi?id=774657
It might've failed just because of flushing or other things, and we
should retry again on the next possibility if something ever calls in
here again.
https://bugzilla.gnome.org/show_bug.cgi?id=774623
Check the correct segment format value.
parse->segment.format is the format we're outputting in,
not the upstream format. Use parse->priv->upstream_format instead,
and make sure it's set in pull mode.
If the parser is not parsing a raw elementary stream, restrict
the position, duration and conversion query replies to
things we can sensibly answer about - especially don't do
random conversions to/from bytes.
This is cosmetic as 'late' should never be set during preroll (in pause).
Though code may evolve in the future, so this is good for preventing
potential bugs.
https://bugzilla.gnome.org/show_bug.cgi?id=772468
When the first buffer arrives, we endup calling:
->prepare()
->prepare()
->preroll()
->render()
This will likely confuse any element using this method. With this patch,
we ensure the preroll take place before the first render prepare() is
called. This will result in:
->prepare()
->preroll()
->prepare()
->render()
https://bugzilla.gnome.org/show_bug.cgi?id=772468
Hurd also defines __MACH__, but it does not have mach_absolute_time. Use
the more strict __APPLE__ instead.
Has also been sent upstream: https://github.com/libcheck/check/pull/65
This reverts commit 2e278aeb71.
Some parsers, specifically audio parsers, assume to get all remaining
data on EOS and just pass them onwards. While the idea here is correct,
we will probably need a property for this on baseparse for parsers to
opt-in.
https://bugzilla.gnome.org/show_bug.cgi?id=773666
Implement handling in basesink to not unconditionally discard
out-of-segment buffers and expose it as a new property on fakesink
(not unconditionally in all basesink based sinks).
The property defaults to FALSE.
https://bugzilla.gnome.org/show_bug.cgi?id=765734
baseparse would pass whatever is left in the adapter to the
subclass when draining, even if it's less than the minimum
frame size required. This is bogus, baseparse should just
discard that data then. The original intention of that code
seems to have been that if we have more data available than
the minimum required we should pass all of the data available
and not just the minimum required, which does make sense, so
we'll continue to do that in the case that more data is available.
Fixes assertions in rawvideoparse on EOS after not-negotiated with
fakesrc sizetype=random ! queue ! rawvideoparse format=rgb ! appsink caps=video/x-raw,format=I420
https://bugzilla.gnome.org/show_bug.cgi?id=773666
The durations of the buffers are (usually) assuming that no frames are being
dropped and are just the durations coming from the stream. However if we do
trickmodes, frames are being dropped regularly especially if only key units
are supposed to be played.
Fixes completely bogus QoS proportion values in the above case.
https://github.com/mesonbuild/meson
With contributions from:
Tim-Philipp Müller <tim@centricular.com>
Mathieu Duponchelle <mathieu.duponchelle@opencreed.com>
Jussi Pakkanen <jpakkane@gmail.com> (original port)
Highlights of the features provided are:
* Faster builds on Linux (~40-50% faster)
* The ability to build with MSVC on Windows
* Generate Visual Studio project files
* Generate XCode project files
* Much faster builds on Windows (on-par with Linux)
* Seriously fast configure and building on embedded
... and many more. For more details see:
http://blog.nirbheek.in/2016/05/gstreamer-and-meson-new-hope.htmlhttp://blog.nirbheek.in/2016/07/building-and-developing-gstreamer-using.html
Building with Meson should work on both Linux and Windows, but may
need a few more tweaks on other operating systems.
If segment.stop was given, and the subclass provides a size that might be
smaller than segment.stop and also smaller than the actual size, we would
already stop there.
Instead try reading up to segment.stop, the goal is to ignore the (possibly
inaccurate) size the subclass gives and finish until segment.stop or when the
subclass tells us to stop.
Waiting before posting calculated bitrates seems to be the
intent of the code, so avoid adding them to the tag list
pushed with the first frame.
When the threshold is reached, gst_base_parse_update_bitrates
sets tags_changed, so this posts the calculated ones right
that moment.
This prevents an insane average calculated from just the
first (key) frame from getting posted.
https://bugzilla.gnome.org/show_bug.cgi?id=768439
There must be a SEGMENT event before the GAP event, and SEGMENT events must
come after any CAPS event. We however did not produce any CAPS yet, so we need
to ensure to insert the CAPS event before the SEGMENT event into the pending
events list.
https://bugzilla.gnome.org/show_bug.cgi?id=766970
If we were in PAUSED, the current clock time and base time don't have much to
do with the running time anymore as the clock might have advanced while we
were PAUSED. The system clock does that for example, audio clocks often don't.
Updating the start time in PAUSED will cause a) the wrong position to be
reported, b) step events to step not just the requested amount but the amount
of time we spent in PAUSED. The start time should only ever be updated when
going from PLAYING to PAUSED to remember the current running time (to be able
to compensate later when going to PLAYING for the clock time advancing while
PAUSED), not when we are already in PAUSED.
Based on a patch by Kishore Arepalli <kishore.arepalli@gmail.com>
The updating of the start time when the state is lost was added in commit
ba943a82c0 to fix the position reporting when
the state is lost. This still works correctly after this change.
https://bugzilla.gnome.org/show_bug.cgi?id=739289
We don't do calculations with different units (buffer offsets and bytes)
anymore but have functions for:
1) getting the number of bytes since the last discont
2) getting the offset (and pts/dts) at the last discont
and the previously added function to get the last offset and its distance from
the current adapter position.
https://bugzilla.gnome.org/show_bug.cgi?id=766647
API: gst_buffer_prev_offset
API: gst_buffer_get_offset_from_discont
The gst_buffer_get_offset_from_discont() method allows retrieving the current
offset based on the GST_BUFFER_OFFSET of the buffers that were pushed in.
The offset will be set initially by the GST_BUFFER_OFFSET of
DISCONT buffers, and then incremented by the sizes of the following
buffers.
The gst_buffer_prev_offset() method allows retrievent the previous
GST_BUFFER_OFFSET regardless of flags. It works in the same way as
the other gst_buffer_prev_*() methods.
https://bugzilla.gnome.org/show_bug.cgi?id=766647
The subclass should do that already, but just in case do it ourselves too as a
fallback. Without this, e.g. playbin will just wait forever if this fails
because it is triggered as part of an ASYNC state change.
POSIX standards requires strsignal() to return a pointer to a char,
not a const pointer to a char. [1] On uClibc, and possibly other
libc's, that do not HAVE_DECL_STRSIGNAL, libcompat.h declares
const char *strsignal (int sig) which causes a type error.
[1] man 3 strsignal
https://bugzilla.gnome.org/show_bug.cgi?id=763567
To allow the GstTestClock to be used as a GstSystemClock, it is
useful to implement the clock-type property that GstSystemClock
provides. This allows GstTestClock to be used as the system clock
with code that expects a GstSystemClock.
https://bugzilla.gnome.org/show_bug.cgi?id=762147
Otherwise PTS and DTS will come out of sync if upstream continues to provide
PTS and not DTS, and we have to skip some data from the stream or PTS are not
exactly increasing with the duration of each packet.
https://bugzilla.gnome.org/show_bug.cgi?id=765260
gsttypefindhelper.c:485: Warning: GstBase: invalid "transfer" annotation for gsize: only valid for array, struct, union, boxed, object and interface types
If we don't store the value in prev_dts, we would over and over again
initialize the DTS from the last known upstream PTS. If upstream only provides
PTS every now and then, then this causes DTS to be rather static.
For example in adaptive streaming scenarios this means that all buffers in a
fragment will have exactly the same DTS while the PTS is properly updated. As
our queues are now preferring to do buffer fill level calculations on DTS,
this is causing huge problems there.
See https://bugzilla.gnome.org/show_bug.cgi?id=691481#c27 where this part of
the code was introduced.
https://bugzilla.gnome.org/show_bug.cgi?id=765096
It is calling do_sync(), which requires the STREAM_LOCK and PREROLL_LOCK to be
taken. The STREAM_LOCK is already taken in all callers, the PREROLL_LOCK not.
https://bugzilla.gnome.org/show_bug.cgi?id=764939
This is the best guess we can make if such a buffer reached the collect
pad. This is uncommon, we do expect parsers to have tried and fixed that
if possible (or needed).
https://bugzilla.gnome.org/show_bug.cgi?id=762207
POSIX standards requires strsignal() to return a pointer to a char,
not a const pointer to a char. [1] On uClibc, and possibly other
libc's, that do not HAVE_DECL_STRSIGNAL, libcompat.h declares
const char *strsignal (int sig) which causes a type error.
[1] man 3 strsignal
https://bugzilla.gnome.org/show_bug.cgi?id=763567
Many parsers are storing tags only in pre_push_frame(), if we wouldn't check
afterwards we would push buffers before those tags and a lot of code assumes that
tags are available before preroll.
https://bugzilla.gnome.org/show_bug.cgi?id=763553
Similar to the stress test functions for buffers that has a callback to
create the buffer to be pushed, it's useful to have functions that use a
callback to create the event to be pushed.
API: gst_harness_stress_push_event_with_cb_start()
API: gst_harness_stress_push_event_with_cb_start_full()
API: gst_harness_stress_send_upstream_event_with_cb_start()
API: gst_harness_stress_push_upstream_event_with_cb_start_full()
https://bugzilla.gnome.org/show_bug.cgi?id=761932
Depending on when gst_harness_pull was called - before the buffer reached
gst_harness_chain or after we can get different behaviors of the test
with enabled blocking push mode. The fix makes the behavior always the
same. In pull function we get the buffer first, thus making sure
gst_harness_chain waits for the signal, and emitting the signal after.
https://bugzilla.gnome.org/show_bug.cgi?id=761931
Set the sink_forward_pad to NULL before tearing down sink_harness to
avoid that the harness tries to forward events/queries to it while it's
tearing down.
https://bugzilla.gnome.org/show_bug.cgi?id=761904
We have no guarantees about what flags are set on buffers we take
out of the GstAdapter. If we push out multiple buffers from the
first input buffer (which will have discont set), only the first
buffer we push out should be flagged as discont, not all of the
buffers produced from that first initial input buffer.
Fixes issue where the first few mp3 frames/seconds of data in push
mode were skipped or garbled in some cases, and the discont flags
would also trip up decoders which were getting drained/flushed for
every buffer. This was a regression introduced in 1.6 apparently.
Does not matter here but makes Coverity more happy. It can't
know that g_list_remove() only looks at the pointer value but
does not dereference it.
CID 1348454
Currently, the query values are being set even if the query itself was
determined to have failed. Fix this to ensure the values are only set in
case of a query success.
https://bugzilla.gnome.org/show_bug.cgi?id=760479
There's not much lost by having the clock idle around a bit longer but it will
potentially allow anybody wanting to use the same clock server again to sync
much faster.
If multiple net/NTP clocks are created for the same server, reuse the same
internal clock for all of them. This makes sure that we don't flood the server
with too many requests and also possibly allows faster synchronization if
there already was an earlier synchronized clock when creating a new one.
Watching videos with variant bitrate is common to have delta
more than 10 kbps, resulting in tag list spam.
Instead of relying on fixed 10 kpbs delta, it is better to
calculale the difference in percentage and update tag list
only when bitrate changes more than 2%.
https://bugzilla.gnome.org/show_bug.cgi?id=759055
My previous fix for #758029 wasn't quite right and simply made the race rarer.
Some of the files are installed by install-exec and others by install-exec, so
the hooks need to be split too.
https://bugzilla.gnome.org/show_bug.cgi?id=758029
This reverts commit 2c475a0355.
This causes issues with h264parse. It breaks timestamps as
there are headers in the middle of the stream and this patch
makes the timestamps for those differ from the ones that
are adjusted, creating a discontinuity and leading to sync
issues.
Otherwise the buffer was left with the original values and later would
be compared with other buffers that were converted to runninn time,
leading to bad interleaving of multiple streams.
https://bugzilla.gnome.org/show_bug.cgi?id=757961
baseparse tries to preserve timestamps from upstream if
it is running on a time segment and write that to
output buffers. It assumes the first DTS is going to be
segment.start and sets that to the first buffers. In case
the buffer is a header buffer, it had no timestamps and
will have only the DTS set due to this mechanism.
This patch prevents this by skipping this behavior for
header buffers.
https://bugzilla.gnome.org/show_bug.cgi?id=757961
The install hook needs to be a install-data-hook not an install-exec-hook as the
helpers are installed into helperdir which is considered data (only path
variables with "exec" in are considered executables).
The explicit dependency on install-helpersPROGRAMS was an attempt at solving
this, but this causes occasional races where install-helpersPROGRAMS can run
twice in parallel (once via install-all, once via the hook's dependency).
https://bugzilla.gnome.org/show_bug.cgi?id=758029
They take a GstBaseSink instance as argument at not a GstPad. Rename the
argument to 'obj' which is not miss leading and in line with
GST_BASE_SINK_PAD(obj).
https://bugzilla.gnome.org/show_bug.cgi?id=756954
In file included from gst-ptp-helper.c:40:0:
/usr/include/net/if.h:265:19: error: field 'ifru_addr' has incomplete type
struct sockaddr ifru_addr;
https://bugzilla.gnome.org/show_bug.cgi?id=756136
When g_option_context_parse fails, context and error variables are not getting free'd
which results in memory leaks. Free'ing the same.
And replacing g_error_free with g_clear_error, which checks if the error being passed
is not NULL and sets the variable to NULL on free'ing.
https://bugzilla.gnome.org/show_bug.cgi?id=753851
The default padding I introduced in d4f81fb4e6 is
actually only 4 pointers and on 32bit platforms already smaller than the union.
Replace it with a fixed 64byte padding. Don't add the normal padding for now.
Fixes#755822
Broke this when I removed the G_GNUC_PRINTF in a previous
commit to fix indentation, since it was not really needed.
Turns out unlike gcc clang warns though if a non-literal
format string is passed then. Fix indentation differently.
http://clang.llvm.org/docs/AttributeReference.html#format-gnu-format
While this technically is an abi break, we decided to do this:
1) the struct is documented to be internal
2) the struct is alloced and freed inside the library
3) there are no public methods that receive or return instances
4) the only code known to use this struct are classes containd here
gst_segment_to_position might cause confusion, especially with the addition of
gst_segment_position_from_stream_time . Deprecated gst_segment_to_position
now, and replaced it with gst_segment_position_from_running_time.
Also added unit tests.
In order for gst_harness_new_full to be MT-safe the increase and
decrease of HARNESS_REF must be MT-safe. This allows for creating
multiple harnesses from different threads wrapping the same element.
https://bugzilla.gnome.org/show_bug.cgi?id=754661
1. Get a list of pad templates from the element class, not the
factory. This allows us to interact with test-elements that does
not have a factory.
2. Use the pad_template_caps in caps-queries when caps is not set
explicitly on the pad. Not doing so is simply wrong, and prohibits
interactions with special templates used for testing.
https://bugzilla.gnome.org/show_bug.cgi?id=754193
There exist cases where a reconfigure event was propagated from
downstream, but caps didn't change. In this case, we would
reconfigure only when the next buffer arrives. The problem is that
due to the allocation query being cached, the return query parameters
endup outdated.
In this patch we refactor the reconfigurating code into a function, and
along with reconfiguring when a new buffer comes in, we also reconfigure
when a query allocation arrives.
https://bugzilla.gnome.org/show_bug.cgi?id=753850
Explicitly keep track again whether upstream tags or parser tags
already contain bitrate information, and only force a tag update
for a bitrate if we are actually going to add the bitrate to the
taglist later. This fixes constant re-sending of the same taglist,
because upstream provided a bitrate already and we didn't add it,
so we didn't save the 'posted' bitrate, which would then in turn
again trigger the 'bitrate has changed too much, update tags'
code path. Fixes tag spam with m4a files for example.
https://bugzilla.gnome.org/show_bug.cgi?id=679768
In 0.10 there were no sticky events, and all tag events
sent would just be merged with the previously-received
tags. In 1.x we have sticky events, and the tags in the
tag event(s) should at all times carry the complete tags,
so we can't just push some tags and then just push tags
with just bitrates to update the bitrates, etc.
Instead we need to keep track of the upstream stream tags
received, of the tags set by the video decoder subclass,
and send an updated tag event with the combined tags
including our own bitrate tags (if applicable) whenever
the upstream tags, the subclass tags or any of our bitrates
change.
https://bugzilla.gnome.org/show_bug.cgi?id=679768
This is needed so that we can do proper tag handling
all around, and combine the upstream tags with the
tags set by the subclass and any extra tags the
base class may want to add.
API: gst_base_parse_merge_tags()
https://bugzilla.gnome.org/show_bug.cgi?id=679768
Use gst_pad_peer_query_duration() and remove a few
unnecessary levels of indentation. Rest of code might
looks a bit questionable, but leave it as is for now.
According to the design docs:
The ACCEPT_CAPS query is not required to work recursively, it can simply
return TRUE if a subsequent CAPS event with those caps would return
success.
So make it a shallow check instead of recursivelly check downstream.
https://bugzilla.gnome.org/show_bug.cgi?id=748635
GstPad has a flag for suggesting if the accept-caps
query should use intersect instead of the default
subset caps operation to verify if the caps would be
acceptable.
basetransform currently always uses the subset check and
this patch makes it honor the flag for using intersect
if it is set.
https://bugzilla.gnome.org/show_bug.cgi?id=748635
To be able to disable the slightly "magic" forwarding of the
necessary events between the harnesses.
Also introduce a new test-suite for GstHarness, that documents the
feature, and should hopefully expand into documenting most of the
features the harness possesses.
https://bugzilla.gnome.org/show_bug.cgi?id=752746
As of now, even for stream completly inside segment, there is no
guarantied that the DTS will be inside the segment. Specifically
for H.264 with B-Frames, the first few frames often have DTS that
are before the segment.
Instead of using the sync timestamp to clip out of segment buffer,
take the duration from the start/stop provided by the sub-class, and
check if the pts and pts_end is out of segment.
https://bugzilla.gnome.org/show_bug.cgi?id=752791
Even though asserts can't be disabled in GstHarness, Coverity still
complains about running code inside them. Moving the code to outside the
g_asserts().
CID #1311326, #1311327, #1311328
gst_query_find_allocation_meta() requires the query to be
writable to work. This patch ensure avoids taking a reference
on the query, so we can now check if a certain allocation meta
is present.
https://bugzilla.gnome.org/show_bug.cgi?id=752661
By introducing gst_harness_add_src_harness and gst_harness_add_sink_harness
we collect all sub-harness setup in one function, making the previous
sub-harness creation functions now calls these directly, and making it
much easier (and less error-prone) to add your own src or sink-harness
using the more generic harness-creation functions.
This line has no purpose, clearly gst_segment_do_seek() is doing
the right job, also, having the start time (a timestamp) be that
same as time (the stream time) is quite odd.
https://bugzilla.gnome.org/show_bug.cgi?id=750783
The element flag does not indicate wether a bin should be tested as a
source or as a sink, eg. a bin with the sink flag may still have a
source pad and a bin with the source flag may have a sink pad. In this
case it is better to determine the element type by looking at the
available pads and pad templates.
Also rename srcpad and sinkpad where it actually represents
element_srcpad_name and element_sinkpad_name.
https://bugzilla.gnome.org/show_bug.cgi?id=752493
For files which are smaller than 1.5 seconds, the duration
estimation does not happen. So the duration will always be
displayed as 0. Updating the duration on EOS when the estimation
has not happened already
https://bugzilla.gnome.org/show_bug.cgi?id=750131
We must make the buffer writable to write its PTS and DTS, and also
reset its duration.
The behaviour is now the same as before commit c3bcbadd, except metas
might still be attached to the buffer extracted from the adapter.
https://bugzilla.gnome.org/show_bug.cgi?id=752092
This way we don't have to allocate/free temporary structs
for storing things in the queue array.
API: gst_queue_array_new_for_struct()
API: gst_queue_array_push_tail_struct()
API: gst_queue_array_peek_head_struct()
API: gst_queue_array_pop_head_struct()
API: gst_queue_array_drop_struct()
https://bugzilla.gnome.org/show_bug.cgi?id=750149
POOL meta just means that this specific instance of the meta is related to a
pool, a copy should be made when reasonable and the flag should just not be
set in the copy.
POOL meta just means that this specific instance of the meta is related to a
pool, a copy should be made when reasonable and the flag should just not be
set in the copy.
This preserves GstMeta properly unless the subclass does special things. It's
enough to make h264parse's stream-format/alignment conversion pass through
metas as needed.
https://bugzilla.gnome.org/show_bug.cgi?id=742385
All functions that return a GstBuffer or a list of them will now copy
all GstMeta from the input buffers except for meta with GST_META_FLAG_POOLED
flag or "memory" tag.
This is similar to the existing behaviour that the caller can't assume
anything about the buffer flags, timestamps or other metadata. And it's
also the same that gst_adapter_take_buffer_fast() did before, and what
gst_adapter_take_buffer() did if part of the first buffer or the complete
first buffer was requested.
https://bugzilla.gnome.org/show_bug.cgi?id=742385
The doc generator get confused with the inline structure. So
workaround by wrapping the inner of the structure with
public/private mark, and document that GST_COLLECT_PADS_DTS macro
shall be used to access this.
* Fix function name in sections.txt
* Add few missing or fix miss-named
* Workaround gtk-doc being confused with non typedef
types (loose track of public/private
There was few Since: mark missing their column. Also unify the way
we set the Since mark on enum value and structure members. These
sadly don't show up in the index.
These are not usable as they are, and can easily lead to crash
or leaks. This also silence warning from the scanner. If we manage to
make this usable, we can then remove that mark, it will require
to make this type boxed.
gstbasetransform.h:196: Warning: GstBase: "@submit_input_buffer" parameter unexpected at this location:
* @submit_input_buffer: Function which accepts a new input buffer and pre-processes it.
gstnetcontrolmessagemeta.c:103: Warning: GstNet: gst_buffer_add_net_control_message_meta: unknown parameter 'message' in documentation comment, should be 'addr'
Make gst_collect_pads_clip_running_time() function also store the
signed DTS in the CollectData. This signed DTS value can be used by
muxers to properly handle streams where DTS can be negative initially.
https://bugzilla.gnome.org/show_bug.cgi?id=740575
The internal clock is only used for slaving against the remote clock, while
the user-facing GstClock can be additionally slaved to another clock if
desired. By default, if no master clock is set, this has exactly the same
behaviour as before. If a master clock is set (which was not allowed before),
the user-facing clock is reporting the remote clock as internal time and
slaves this to the master clock.
This also removes the weirdness that the internal time of the netclientclock
was always the system clock time, and not the remote clock time.
https://bugzilla.gnome.org/show_bug.cgi?id=750574
Allow for sub-classes which want to collate incoming buffers or
split them into multiple output buffers by separating the input
buffer submission from output buffer generation and allowing
for looping of one of the phases depending on pull or push mode
operation.
https://bugzilla.gnome.org/show_bug.cgi?id=750033
This uses all of the netclientclock code, except for the generation and
parsing of packets. Unfortunately some code duplication was necessary
because GstNetTimePacket is public API and couldn't be extended easily
to support NTPv4 packets without breaking API/ABI.
We extend our calculations to work with local send time, remote receive time,
remote send time and local receive time. For the netclientclock protocol,
remote receive and send time are assumed to be the same value.
For the results, this modified calculation makes absolutely no difference
unless the two remote times are different.
This improves accuracy on wifi or similar networks, where the RTT can go very
high up for a single observation every now and then. Without filtering them
away completely, they would still still modify the average RTT, and thus all
clock estimations.
They don't necessarily use the same underlying clocks (e.g. on Windows), or
might be configured to a different clock type (monotonic vs. real time clock).
We need the values a clean system clock returns, as those are the values used
by the internal clocks.
If the delay measurement is too far away from the median of the window of last
delay measurements, we discard it. This increases accuracy on wifi a lot.
https://bugzilla.gnome.org/show_bug.cgi?id=749391
We should do some more measurements with all these and check how much sense
they make for PTP. Also enabling them means not following IEEE1588-2008 by the
letter anymore.
https://bugzilla.gnome.org/show_bug.cgi?id=749391
GstPtpClock implements a PTP (IEEE1588:2008) ordinary clock in
slave-only mode, that allows a GStreamer pipeline to synchronize
to a PTP network clock in some specific domain.
The PTP subsystem can be initialized with gst_ptp_init(), which then
starts a helper process to do the actual communication via the PTP
ports. This is required as PTP listens on ports < 1024 and thus
requires special privileges. Once this helper process is started, the
main process will synchronize to all PTP domains that are detected on
the selected interfaces.
gst_ptp_clock_new() then allows to create a GstClock that provides the
PTP time from a master clock inside a specific PTP domain. This clock
will only return valid timestamps once the timestamps in the PTP domain
are known. To check this, the GstPtpClock::internal-clock property and
the related notify::clock signal can be used. Once the internal clock
is not NULL, the PTP domain's time is known. Alternatively you can wait
for this with gst_ptp_clock_wait_ready().
To gather statistics about the PTP clock synchronization,
gst_ptp_statistics_callback_add() can be used. This gives the
application the possibility to collect all kinds of statistics
from the clock synchronization.
https://bugzilla.gnome.org/show_bug.cgi?id=749391
Just create the cancellable fd once and keep it around instead
of creating/closing it for every single packet. Since we spend
most time waiting for packets, an fd is alloced and in use pretty
much all the time anyway.
We were segfaulting because g_sequence_search was returning the iter_end,
and that iterator does not contain anything and thus should not be used
directly
In basesink functions gst_base_sink_chain_unlocked(), below code is used to
checking if buffer is late before doing prepare call to save some effort:
if (syncable && do_sync)
late =
gst_base_sink_is_too_late (basesink, obj, rstart, rstop,
GST_CLOCK_EARLY, 0, FALSE);
if (G_UNLIKELY (late))
goto dropped;
But this code has problem, it should calculate jitter based on current media
clock, rather than just passing 0. I found it will drop all the frames when
rewind in slow speed, such as -2X.
https://bugzilla.gnome.org/show_bug.cgi?id=749258
Since frame->priv->discont was cleared earlier,
GST_BASE_PARSE_FLAG_LOST_SYNC was never being set.
Take the chance to refactor the frame creation a bit to
organize the flags setting and reset.
https://bugzilla.gnome.org/show_bug.cgi?id=738237
Otherwise we're going to set a rather arbitrary DTS of segment.start (usually
0) for live sources, which confuses synchronization if the source started
capturing at a later time. And it's especially wrong for raw media, for which
we should not set any DTS at all.
https://bugzilla.gnome.org/show_bug.cgi?id=747731
It could be triggered by:
gst-launch-1.0 videotestsrc num-buffers=20 ! videcrop bottom=214748364 ! videoconvert ! autovideosink
Spotted while testing:
https://bugzilla.gnome.org/show_bug.cgi?id=743910
The flush-stop event should not restart the task for live sources unless
the element is playing. This was breaking seeks in pause with the rtpsrc.
https://bugzilla.gnome.org/show_bug.cgi?id=635701
Otherwise baseparse will consider empty streams to be an error while
an empty stream is a valid scenario. With this patch, errors would
only be emitted if the parser received data but wasn't able to
produce any output from it.
This change is only for push-mode operation as in pull mode an
empty file can be considered an error for the one driving the
pipeline
Includes a unit test for it
https://bugzilla.gnome.org/show_bug.cgi?id=733171
check_run.c: In function 'sig_handler':
check_run.c:127:13: warning: 'child_sig' may be used uninitialized in this function [-Wmaybe-uninitialized]
killpg(group_pid, child_sig);
^
check_run.c:130:31: warning: 'idx' may be used uninitialized in this function [-Wmaybe-uninitialized]
sigaction(sig_nr, &old_action[idx], NULL);
^
Otherwise e.g. ctrl+c in the test runner exits the test runner, while the test
itself is still running in the background, uses CPU and memory and potentially
never exits (e.g. if the test ran into a deadlock or infinite loop).
The reason why we have to manually kill the actual tests is that after
forking they will be moved to their own process group, and as such are
not receiving any signals sent to the test runner anymore. This is supposed
to be done to make it easier to kill a test, which it only really does if
the test itself is forking off new processes.
This fix is not complete though. SIGKILL can't be caught at all, and error
signals like SIGSEGV, SIGFPE are currently not caught. The latter will only
happen if there is a bug in the test runner itself, and as such seem less
important.
Large scale skip is an optimization, and thus it is safer to
stop skipping than to continue. Clear skip on segments and
discontinuities, as these are points where it is possible that
the original idea of "bytes to skip" changes.
GstNetAddress can be used to store ancillary data which was received with
or is to be sent alongside the buffer data. When used with socket sinks
and sources which understand this meta it allows sending and receiving
ancillary data such as unix credentials (See `GUnixCredentialsMessage`)
and Unix file descriptions (See `GUnixFDMessage`).
This will be useful for implementing protocols which use file-descriptor
passing in payloaders/depayloaders without having to re-implement all the
socket handling code already present in elements such as multisocketsink,
etc. This, in turn, will be useful for implementing zero-copy video IPC.
This meta uses the platform independent `GSocketControlMessage` API
provided by GLib as a part of GIO. As a result this new meta does not
require any new dependencies or any conditional compliation for
portablility, although it is unlikely to do anything useful on non-UNIX
platforms.
Allows buffers to be reclaimed when caps is to be renegotiated so
that bufferpools can be stopped. As the allocation query is
serialized all buffers have been already drained from the pipeline,
except this last_sample one.
https://bugzilla.gnome.org/show_bug.cgi?id=682770
Use gst_buffer_copy_deep() to force the copy of the underlying
memory instead of possibly doing a shallow copy of the buffer
and just referencing the memory
https://bugzilla.gnome.org/show_bug.cgi?id=745287
Based on patch from Song Bing <b06498@freescale.com>
Don't just set the need_preroll flag to TRUE in all cases. When we
are already prerolled it needs to be set to FALSE and when we go to
READY we should not touch it. We should only set it to TRUE in other
cases, like what the code above does.
See https://bugzilla.gnome.org/show_bug.cgi?id=736655
