If we are using an adaptive stream demuxer, which outputs a non-container
stream, we are putting another multiqueue after the *parser* following
the adaptive stream demuxer. We do not want to add another instance of
the same parser right after this multiqueue.
Otherwise we will emit buffering messages not just from the last
multiqueue but also from previous multiqueues... confusing the
application with different percentages during pre-rolling.
For adaptive streaming demuxer we insert a multiqueue after
this demuxer. This multiqueue will get one fragment per buffer.
Now for the case where we have a container stream inside these
buffers, another demuxer will be plugged and after this second
demuxer there will be a second multiqueue. This second multiqueue
will get smaller buffers and will be the one emitting buffering
messages.
If we don't have a container stream inside the fragment buffers,
we'll insert a multiqueue below right after the next element after
the adaptive streaming demuxer. This is going to be a parser or
decoder, and will output smaller buffers.
Adaptive streams should download its data inside the demuxer, so
we want to use multiqueue's buffering messages to control the
pipeline flow and avoid losing sync if download rates are low;
https://bugzilla.gnome.org/show_bug.cgi?id=707636
Otherwise there's an interesting race condition when we destroy
the inputselector (actually it will be destroyed later when its state
change message gets destroyed) and afterwards release its sinkpad.
This is the code path when the last channel is removed from the
input selector.
Gave this warning sometimes, for chained oggs or whenever else
we change decode groups:
GStreamer-CRITICAL **: Padname '':sink_0 does not belong to element inputselector0 when removing
If the text pads does not go away we just set the overlay to silent, which
allows us to immediately re-enable subs later again. However before this
change we also released the streamsynchronizer text pads, which deadlocked
because there was still dataflow going on. Just do this only if we remove
the complete chain.
https://bugzilla.gnome.org/show_bug.cgi?id=683504
Change the way autoplug-select is accumulated so that it's possible to have
multiple handlers. The handlers keep getting called as long as they keep
returning GST_AUTOPLUG_SELECT_TRY.
One practical example of when this is needed is when hooking into playbin's
uridecodebin, which is perhaps not very elegant but the only way to influence
which streams playbin autoplugs/exposes.
Fixes https://bugzilla.gnome.org/show_bug.cgi?id=723096
Discussion on IRC indicated that the main reason for this list was to
prevent demuxers that can trigger a lot of seeking from using
progressive buffering using queue2 (which due to being seekable triggers
that behaviour).
However given that upstream can indicate seeks are possible but should
be avoided via a scheduling query, this extra whitelisting shouldn't be
necessary for well-behaved demuxers.
https://bugzilla.gnome.org/show_bug.cgi?id=704933
If a pipeline fails to preroll, it might happen that the sinks are
put into READY state from playbin's sink activation, but they are never
set to playsink, so they aren't being managed by a GstBin and will keep
their READY state until they are unreffed, leading to a warning.
Prevent this by always forcing them to NULL when deactivating a group
https://bugzilla.gnome.org/show_bug.cgi?id=708789
Otherwise we will remove the bus that would proxy messages to playsink
and never set it again. If the sink is already in playsink, all failures
are fatal anyway as it's either a sink that worked before or one that
was set by the user.
https://bugzilla.gnome.org/show_bug.cgi?id=701997
playbin will now only activate the sinks in a single place and
will never change the states of any sinks that are owned by
playsink.
Also handle text-sinks the same way as audio/video sinks inside
playbin.
This makes sure the application gets any context related messages and
can do whatever is required to a) get the sink a context or b) share
the context with other elements in the pipeline.
The proxying is necessary because the sink is not a child element of
playbin, but instead will at a later point be a child of some bin
inside playsink.
https://bugzilla.gnome.org/show_bug.cgi?id=700967
Otherwise we're going to deadlock forever because no autoplugging
happens without having caps, but caps can never be send because
we're blocking.
Serialized queries before caps should never be sent unless really
necessary.
We found a case where untranslated values were being passed from the
proxy to the underlying channel, causing bad color balance values
in some setups.
Thanks to Sebastian Dröge for clarifying how the code works, and
suggesting the fix.
Fixes https://bugzilla.gnome.org/show_bug.cgi?id=701202
This allows to chose something else than input-selector
for multiple audio/video/text streams, e.g. an adder could
be used for audio.
It is needed for example to implement some of the more
advanced HTML5 video features.
https://bugzilla.gnome.org/show_bug.cgi?id=698851
Add the actual decoder/parser/etc caps at the very end to
make sure we don't cause empty caps to be returned, e.g.
if a parser asks us but a decoder is required after it
because no sink can handle the format directly.
Otherwise we will only block after the serialized, non-sticky event
after the CAPS event or the first buffer. If we're waiting for another
pad to finish autoplugging after we got final caps on this pad, it
will mean that we will let the ALLOCATION query pass although the
pad is not exposed yet.
Otherwise we accumulate more and more queue2 elements, and let each
of them start a thread doing nothing but waiting each time uridecodebin
goes to PAUSED.
https://bugzilla.gnome.org/show_bug.cgi?id=699794
This makes it possible to take advantage of the O(log n) lookups
of GSequence on the ~1000 element lists and only do iterations
on <10 element lists. Previously the code iterated over ~1000 element
lists multiple times.
