The MPEG standard (ISO-13880-1) says the reserve bits need to be set
to one (2.1.64). This is causing transport streams to fail validation
on some systems.
https://bugzilla.gnome.org/show_bug.cgi?id=760127
This works usually in this place, unless the compiler optimizes things in
interesting ways in which case it causes stack corruption and crashes later.
The compiler in question here is clang with -O1, which seems to pack the stack
a bit more and causes writing to the guint as pointer to overwrite map.memory,
which then later crashes during unmapping of the memory.
While encoding the frame in ASCII mode, per component four bytes are needed
and after every 20 bytes, a \n will be added. So the calculation should be
size = size * (4 + 1 / 20). This should exclude the header being written.
Since header is also being included in the calculations, memory mishandlings
are happening.
https://bugzilla.gnome.org/show_bug.cgi?id=759520
rename gst-launch --> gst-launch-1.0
replace old elements with new elements(ffmpegcolorspace -> videoconvert, ffenc_** -> avenc_**)
fix caps in examples
https://bugzilla.gnome.org/show_bug.cgi?id=759432
The edit rate is only supposed to be the same in a source package, but there
might be multiple source packages with the same essence container. As such
just comparing the body/index SID is not sufficient.
This was completely broken before and could only work on a very constrained
set of files. After these changes it should work except for situations where
PTS != DTS, which is not handled at all in mxfdemux currently.
https://bugzilla.gnome.org/show_bug.cgi?id=759118
According to S377-1-2009c 9.2 the local tags must not be resolved from the
primer pack, which as a result means that there can't be any other tags than
statically assigned ones.
This is to support byte-stream decoder that does not remember the
PPS/SPS after a flush. This is not needed by all decoders, but is
harmless for those that do remember.
https://bugzilla.gnome.org/show_bug.cgi?id=758405
The order in which program switch must happen is:
1) drain all data on old pads (but don't push EOS)
2) add new pads (but don't push any data on them)
3) Push EOS and remove old pads
4) Start pushing data on new pads
There was one caveat in this implementation, which is that when
we activate a sparse pad (step 2) we would push a GAP event. The problem
is that, while being an event, it is actually *data*.
We therefore need to make sure pushing those GAP event is done at the step
we start pushing data.
https://bugzilla.gnome.org/show_bug.cgi?id=750402
Before we add any streams, make sure we drain all streams. This ensures
there's consistency that only "new" data will be pushed on buffers once
the new pads are added
https://bugzilla.gnome.org/show_bug.cgi?id=750402
When changing programs, the order of events needs to be the following:
* add pads from new program
* send EOS on old pads
* remove old pads
* emit 'no-more-pads'
Previously tsdemux was not doing that, and was first deactivating and
removing old pads before adding new ones.
We fix this by allowing subclasses of mpegtsbase to be able to handle
themselves the deactivation of programs. In this case tsdemux will
properly deactivate it once it has activated the new program.
https://bugzilla.gnome.org/show_bug.cgi?id=750402
The videoframe-audiolevel element acts like a synchronized audio/video "level"
element. For each video frame, it posts a level-style message containing the
RMS value of the corresponding audio frames. This element needs both video and
audio to pass through it. Furthermore, it needs a queue after its video
source.
https://bugzilla.gnome.org/show_bug.cgi?id=748259
0x04 signifies a MPEG elementary stream but according to RP2008, 0x10 should
be used for a h264 byte-stream. This also fixes compatibility of our files
with ffmpeg.
