Remove tee and output-selector and just link the source
pad to the outputs we want as needed.
The way we need to prioritize caps negotiation and allocation
queries depending on the mode enabled is too custom to be
handled using tee and output-selector.
This provides more flexibility and doesn't get in the way of proper
handling of negotiation and allocation queries.
The detection for missing format/alignment is done way before this
codepath is reached (at which point we have already decided of a
format and alignment).
CID #1232800
When block width property is set to 0, exception occurs.
This happens due to divide by zero errors in calculations.
block width property can never be 0. Hence adjusting the minimum value to 1.
https://bugzilla.gnome.org/show_bug.cgi?id=744188
Such seeks are used to change playback rate and we do not want
to alter the position in that case, so we bypass the flush/seek
logic, and set things up so a new segment is scheduled to be
regenerated.
https://bugzilla.gnome.org/show_bug.cgi?id=735100
This will happen when the PMT changes, replacing streams with
new ones. In that case, we need to accumulate the running time
from the previous chain in the segment base.
https://bugzilla.gnome.org/show_bug.cgi?id=745102
Reset the internal segment before freeing it.
mxf_index_table_segment_parse() allocates data inside the segment
(like segment->delta_entries) which have to be freed using
mxf_index_table_segment_reset().
https://bugzilla.gnome.org/show_bug.cgi?id=746803
Also:
- Don't modify size on early buffer
The size is the size of the buffer, not of remaining part.
- Use the input caps when manipulating the input buffer
Also store in in the sink pad
- Reply to the position query in bytes too
- Put GAP flag on output if all inputs are GAP data
- Only try to clip buffer if the incoming segment is in time or samples
- Use incoming segment with incoming timestamp
Handle non-time segments and NONE timestamps
- Don't reset the position when pushing out new caps
- Make a number of member variables private
- Correctly handle case where no pad has a buffer
If none of the pads have buffers that can be handled, don't claim to be EOS.
- Ensure proper locking
- Only support time segments
https://bugzilla.gnome.org/show_bug.cgi?id=740236
When the timeout is reached, only ignore pads with no buffers, iterate
over the other pads until all buffers have been read. This is important
in the cases where the input buffers are smaller than the output buffer.
https://bugzilla.gnome.org/show_bug.cgi?id=745768
Correctly calculate alpha in a few places by dividing by 255,
not 256.
Fix the argb and bgra blending functions to avoid an off-by-one
error in the calculations, so painting with alpha = 0xff doesn't
ever bleed through from behind
Currently the alignment property just makes sure that we
output things in multiples of align*packet_size bytes, but
with no clear maximum size. When streaming MPEG-TS over
UDP one wants buffers with a maximum packet size of 1316.
The alignment property so far would just output buffers
that are a multiple of 1316 then.
Instead we now make the alignment property output
individual buffers with the alignment size, which
is entirely backwards compatible with the expected
behaviour up until now. For efficiency reason
collect all those buffers in a buffer list and
send that downstream.
Also collect data to push downstream in a buffer
list from the adapter if we don't align things,
which is still more efficient because of the
silly way the muxer currently creates output
packets.
https://bugzilla.gnome.org/show_bug.cgi?id=722129
Actually accumulate the sample counter to check the accumulated error
between actual timestamps and expected ones instead of just resetting
the error back to 0 with every new buffer.
Also don't reset discont_time whenever we don't resync. The whole point of
discont_time is to remember when we first detected a discont until we actually
act on it a bit later if the discont stayed around for discont_wait time.
https://bugzilla.gnome.org/show_bug.cgi?id=746032
