When it is not clear yet if a packet relative to a source should be
pushed, the packet is put into a queue, this happens in two cases:
- the source is still in probation;
- there is a large jump in seqnum, and it is not clear what
the cause is, future packets will help making a guess.
In either case stats about received packets are not updated at all; and
even if they were, when init_seq() is called it resets all receiver
stats, effectively loosing any possible stat about previously received
packets.
Fix this by taking into account the queued packets and update the stats
when calling init_seq().
Since commit c971d1a9a (rtpsource: refactor bitrate estimation,
2010-03-02) bytes_received filed in RTPSourceStats is set but then never
used again, expose it so that it can be used by user code to verify how
many bytes have been received.
According to RFC3550 lower-level headers should be considered for
bandwidth calculation.
See https://tools.ietf.org/html/rfc3550#section-6.2 paragraph 4:
Bandwidth calculations for control and data traffic include
lower-layer transport and network protocols (e.g., UDP and IP) since
that is what the resource reservation system would need to know.
Fix the source data to accommodate that.
Assume UDPv4 over IP for now, this is a simplification but it's good
enough for now.
While at it define a constant and use that instead of a magic number.
NOTE: this change basically reverts the logic of commit 529f443a6
(rtpsource: use payload size to estimate bitrate, 2010-03-02)
In order to do that, we now split the nacks registration from the actual
FB nack packet construction. We then try and add as many FB Nacks as
possible into the active packets and leave the remaining seqnums in the
RTPSource. In order to avoid sending outdated NACK later on, we save the
seqnum calculated deadline and cleanup the outdated seqnums before the
next RTCP send.
Fixes#583
The update_receiver_stats() function is called also when sending packets
in rtp_source_send_rtp(), and sending packets may happen using a buffer
list rather than individual buffers.
So update the stats using the actual number of packets sent.
NOTE: this is fine for the receive path too (rtp_process_send_rtp)
because the receive path does not support buffer lists and
pinfo->packets would always be equal to 1 in this case.
In commit 28e5f9098 (rtpbin: use PacketInfo for the sender, 2013-09-13)
the rtp_source_send_rtp signature changed but the documentation was not
adjusted to match the new one.
Update the documentation to match the function signature.
This is useful when implementing custom retransmission mechanism like
RIST to prevent RTCP from being produces for the retransmitted SSRC.
This would also be used in general for various purpose when customizing
an RTP base pipeline.
Reset RTPSession when rtpsession changes state from PAUSED to READY.
Without this change, a stored last_rtptime in RTPSource could interfere
with RTP timestamp generation in RTCP Sender Report.
Fixes#510
Instant large changes to ts_offset may cause timestamps to move
backwards and also cause visible effects in media playback. The new
option max-ts-offset-adjustment lets the application control the rate to
apply changes to ts_offset.
https://bugzilla.gnome.org/show_bug.cgi?id=784002
If update_receiver_stats() fails, we can't really do anything with this buffer
anymore and have to drop it. This happens if there's a big seqnum
discontinuity for example.
https://bugzilla.gnome.org/show_bug.cgi?id=751311
As we now replace the local RTPSource on a conflict, it's no longer possible
to keep local conflicts in the RTPSource, so they instead need to be kept
in the RTPSession.
Also fix the rtpcollision test to generate multiple collisions instead of
one by change the address, as otherwise we detected that it was a single one.
Previously, when the session had multiple internal sender SSRCs, it would
issue SR reports with RB blocks only on the first RTCP timeout and afterwards
SR reports would be sent empty. This was because the "generation" number
in RTPSource would increase more than once during the same cycle and afterwards
it would always be greater than the session's generation, which would cause
it to be skipped from being included in RBs.
This commit fixes this problem by:
1) Increasing the RTPSource generation only at the end of each cycle,
which essentially fixes the problem but only when the internal senders
are less than GST_RTCP_MAX_RB_COUNT.
2) Keeping for each RTPSource a set of SSRCs which stores which SSRC's
SR the given RTPSource has been reported in, which also fixes the problem
when the internal senders are more than GST_RTCP_MAX_RB_COUNT. This is
necessary because of the fact that any RTPSource is marked as reported
in itself's SR and makes it impossible to know if it has been reported
in other SRs too or not, and which.
An internal sender in a session is also a receiver of its own packets so update
the receiver stats. Other senders in the session will use this info to generate
correct RB blocks in their SR reports.
