When a collision is found on the internal ssrc, we have to change it.
Ideally, we want also the payloader upstream to follow this change and use
the new internal ssrc. Ideally we want this condition to be always met:
if there is one payloader sending on this session, its ssrc should match the
internal ssrc.
* gst/rtpmanager/gstrtpbin.[ch]: four new action signals have been
added (request-rtp-encoder, request-rtp-decoder, request-rtcp-encoder
and request-rtcp-decoder). The user will be able to provide encoders
or decoders dynamically. The encoders must follow the srtpenc API and
the decoders the srtpdec API. Having separate signals for RTP and RTCP
allows the user to use different encoders/decoders or provide the same
one (e.g. that would be the case for srtpenc).
Also, rtpbin now allows application/x-srtp in its pads.
https://bugzilla.gnome.org/show_bug.cgi?id=719938
Use the round-trip-time and average jitter to dynamically calculate the
retransmission interval and expected packet arrival time.
Based on patches from Torrie Fischer <torrie.fischer@collabora.co.uk>
Fixes https://bugzilla.gnome.org/show_bug.cgi?id=711412
Don't use the current time calculated from the tmieout loop for when we
last scheduled the NACK because it might be unscheduled because of a max
packet misorder and then we don't accurately calculate the current time.
Instead, take the current element running time using the clock.
Make it clear what should be handled purely by mss mode:
1) Expose the streams on the first moof as there are no moov atoms
2) Properly cleanup streams on flushes
Add a note about the meaning of upstream_newsegment and mss_mode
for future reference.
Make all other special fragment handling shared for both dash
and mss streams.
In a fragmented scenario, qtdemux is operating in push mode
and it gets a fragmented buffer. While processing its data
downstream gets unlinked (or a input-selector changes its
active pad and returns not-linked). Qtdemux stops processing
this fragment and returns not-linked upstream, leaving the
remaining data in its adapter.
When it gets an EOS it should make sure that all the data it
had received is pushed before pushing EOS.
libshout2 (we require > 2.0 at config time) supports
both IP and hostname for _set_host(). Dropped an
outdated FIXME regarding this limitation, adjusted
some comments and changed the param blurb to reflect
this too.
According to RFC 5104 section 4.3.1.2, RTCP PSFB FIR message SHALL
have a media_ssrc field set to 0. The actual media ssrc is in the FCI.
So in that case, we ignore the retained feedback and just let it through
to the rtp_session_process_fir() function which will check for the actual
SSRC inside the FCI.
Fixes a regression introduced by commit 57c27ec3
Previously, when the session had multiple internal sender SSRCs, it would
issue SR reports with RB blocks only on the first RTCP timeout and afterwards
SR reports would be sent empty. This was because the "generation" number
in RTPSource would increase more than once during the same cycle and afterwards
it would always be greater than the session's generation, which would cause
it to be skipped from being included in RBs.
This commit fixes this problem by:
1) Increasing the RTPSource generation only at the end of each cycle,
which essentially fixes the problem but only when the internal senders
are less than GST_RTCP_MAX_RB_COUNT.
2) Keeping for each RTPSource a set of SSRCs which stores which SSRC's
SR the given RTPSource has been reported in, which also fixes the problem
when the internal senders are more than GST_RTCP_MAX_RB_COUNT. This is
necessary because of the fact that any RTPSource is marked as reported
in itself's SR and makes it impossible to know if it has been reported
in other SRs too or not, and which.
This test checks that when we have multiple internal sender sources
in rtpsession, SRs contain RBs for every other sender source, and that
they are included roundrobin when they exceed ST_RTCP_MAX_RB_COUNT,
which is the max number of RBs that can fit in a SR.
