Add a new property "do-aggregate"* to the H.264 RTP payloader which
enables STAP-A aggregation as per [RFC-6184][1]. With aggregation enabled,
packets are bundled instead of sent immediately, up until the MTU size.
Bundles also end at access unit boundaries or when packets have to be
fragmented.
*: The property-name is kept generic since it might apply more widely,
e.g. STAP-B or MTAP.
[1]: https://tools.ietf.org/html/rfc6184#section-5.7
Closes https://gitlab.freedesktop.org/gstreamer/gst-plugins-good/issues/434
If an rtx packet arrives that hasn't been requested (it might
have been requested from prior to a reset), ignore it so that
it doesn't inadvertently trigger a clock skew.
In the case of reordered packets, calculating skew would cause
pts values to be off. Only calculate skew when packets come
in as expected. Also, late RTX packets should not trigger
clock skew adjustments.
Fixes#612
mpegaudioparse suggests MP3 needs 10 or 30 frames of lead-in (depending on
mpegaudioversion, which we don't know here), thus provide at least 30 frames
lead-in for such cases as a followup to commit cbfa4531ee.
The pre_push_frame default clipping behaviour was introduced in 2010
with commit 30be03004e and modified with commit 4163969a24 in 2011,
when most parsers didn't implement a pre_push_frame yet. Not having it
meant that clipping was done by default. Those that did implement a
pre_push_frame (flacparse and mpegaudioparse) at the time, had the flag
adjusted as part of the 2011 refactor work.
All other parsers got a pre_push_frame vfunc implementation only in
2013, but seem to have forgot to keep the clipping behaviour, as
was done automatically when a pre_push_frame implementation doesn't
exist for the parser. aacparse lost it with commit 91d4abcea in
July 2013; the others in Dec 2013 as part of AUDIO_CODEC tag posting
in commits 6f89b430e, d2ab5199b, 29f2cae12, 753d3c23a and 292780574.
Otherwise it can happen that we receive a caps event, then another caps
event and only then buffers. We would then send out the first caps event
in the stream but mark buffers with the caps version of the second caps
event.
Otherwise it can happen that we already collected 7 caps, miss the 8th
caps packet (packet loss) and then re-use the 1st caps for the following
buffers instead of the 8th caps which will likely cause errors further
downstream unless both caps are accidentally the same.
Keeping old caps around does not seem to have any value other than
potentially causing errors. We would always receive new caps whenever
they change (even if they were previous ones) and it's very unlikely
that they happen to be exactly the same as the previous ones.
Also after having received new caps or a buffer with a next caps
version, no buffers with old caps version will arrive anymore.
Make sure to clear any master clock on the media_clock
before unreffing it to release the timer callback that's
updating the clock and keeping it reffed.
Clear the mastering_display_info_present field explicitly
after reallocating the track context into a video context
to avoid uninitialised warnings in valgrind
If, say, a rtx-packet arrives really late, this can have a dramatic
effect on the jitterbuffer clock-skew logic, having it being reset
and losing track of the current dts-to-pts calculations, directly affecting
the packets that arrive later.
This is demonstrated in the test, where a RTX packet is pushed in really
late, and without this patch the last packet will have its PTS affected
by this, where as a late RTX packet should be redundant information, and
not affect anything.
This patch corrects the delay set on EXPECTED timers that are added when
processing gaps. Previously the delay could be too small so that
'timout + delay' was much less than 'now', causing the following retries
to be scheduled too early. (They were sent earlier than
rtx-retry-timeout after the previous timeout.)
Turns out that the "big-gap"-logic of the jitterbuffer has been horribly
broken.
For people using lost-events, an RTP-stream with a gap in sequencenumbers,
would produce exactly that many lost-events immediately.
So if your sequence-numbers jumped 20000, you would get 20000 lost-events
in your pipeline...
The test that looks after this logic "test_push_big_gap", basically
incremented the DTS of the buffer equal to the gap that was introduced,
so that in fact this would be more of a "large pause" test, than an
actual gap/discontinuity in the sequencenumbers.
Once the test was modified to not increment DTS (buffer arrival time) with
a similar gap, all sorts of crazy started happening, including adding
thousands of timers, and the logic that should have kicked in, the
"handle_big_gap_buffer"-logic, was not called at all, why?
Because the number max_dropout is calculated using the packet-rate, and
the packet-rate logic would, in this particular test, report that
the new packet rate was over 400000 packets per second!!!
I believe the right fix is to don't try and update the packet-rate if
there is any jumps in the sequence-numbers, and only do these calculations
for nice, sequential streams.
gst_splitmux_src_activate_part() configures the pad information
before starting the pad task, but occasionally the changes it makes
to the pad are not seen in the pad task because they're not
protected by the right locking. Use the pad's object lock to
protect those variables.
Fix a deadlock around the pads list by using an RW lock to
allow simultaneous readers. The pad list doesn't really changes
except at startup and shutdown.
Make the debug output less confusing by not mentioning a src
pad when doing calculations on the sink pad side.
Improve debug around why a GOP is considered overflowing a fragment
AAC and various other audio codecs need a couple frames of lead-in to
decode it properly. The parser elements like aacparse take care of it
via gst_base_parse_set_frame_rate, but when inside a container, the
demuxer is doing the seek segment handling and never gives lead-in
data downstream.
Handle this similar to going back to a keyframe with video, in the
same place. Without a lead-in, the start of the segment is silence,
when it shouldn't, which becomes especially evident in NLE use cases.
In this change we now protect the internal srcpads list using the
stream lock and limit usage of the internal stream lock to
preventing data flowing on the other src pad type while creating
and signalling the new pad.
This fixes a deadlock with RTPBin shutdown lock. These two locks would
end up being taken in two different order, which caused a deadlock. More
generally, we should not rely on a streamlock when handling out-of-band
data, so as a side effect, we should not take a stream lock when
iterating internal links.
This means we can use some newer features and get rid of some
boilerplate code using the G_DECLARE_* macros.
As discussed on IRC, 2.44 is old enough by now to start depending on it.
It must be accurate for all samples to work in Final Cut properly, so
the best we can do is to assume that all samples are the same as the
first. Bigger samples are truncated, smaller samples are padded.
This takes the timestamp of the earliest stream and offsets it so that
it starts at 0. Some software (VLC, ffmpeg-based) does not properly
handle Matroska files that start at timestamps much bigger than zero.
Closes https://gitlab.freedesktop.org/gstreamer/gst-plugins-good/issues/449
There is only a single sink element in async-finalize mode, and we would
keep the running time from previous fragments set in that case. As we
don't ever set the running time for the very last fragment on EOS, this
would mean that the closing time reported for the very last fragment is
the same as the closing time of the previous fragment.
This is a tiny clarification as the storage was loosely named "storage".
This change clarify that the storage is specificaly used for received RTP
packets. This is unlike the storage found in rtprtxsend that stores a
backlog of sent RTP packets.
We recently added code to remove outdate NACK to avoid using bandwidth
for packet that have no chance of arriving on time. Though, this had a
side effect, which is that it was to get an early RTCP packet with no
feedback into it. This was pretty useless but also had a side effect,
which is that the RTX RTT value would never be updated. So we we stared
having late RTX request due to high RTT, we'd never manage to recover.
This fixes the regression by making sure we keep at least one NACK in
this situation. This is really light on the bandwidth and allow for
quick recover after the RTT have spiked higher then the jitterbuffer
capacity.
The second udpsrc (rtcp) might not have seen the segment event if it was
not enabled or if rtcp is not available on the server. So if the
application tries to send an EOS event it will try to set an invalid
seqnum to the event.
Right now, we may call on-new-ssrc after we have processed the first
RTP packet. This prevents properly configuring the source as some
property like "probation" are copied internally for use as a
decreasing counter. For this specific property, it prevents the
application from disabling probation on auxiliary sparse stream.
Probation is harmful on sparse streams since the probation algorithm
assume frequent and contiguous RTP packets.
Scaletempo doesn't support non-interleaved layout. Not explicitely stating this
would trigger critical warnings and a caps negotiation failure when scaletempo
is used as playbin audio-filter.
Patch suggested by George Kiagiadakis <george.kiagiadakis@collabora.com>.
Fixes#591
Fix doc chunks to not use that syntax for links that have the
url as description, it will be put verbatim into the xml/*.xml
file and then the expat parser will throw a syntax error like:
File "../../common/mangle-db.py", line 71, in <module>
main()
File "../../common/mangle-db.py", line 69, in main
patch (details.replace("-details", ""), os.path.basename(details))
File "../../common/mangle-db.py", line 20, in patch
doc = xml.dom.minidom.parse(related)
File "/usr/lib/python2.7/xml/dom/minidom.py", line 1918, in parse
return expatbuilder.parse(file)
File "/usr/lib/python2.7/xml/dom/expatbuilder.py", line 924, in parse
result = builder.parseFile(fp)
File "/usr/lib/python2.7/xml/dom/expatbuilder.py", line 207, in parseFile
parser.Parse(buffer, 0)
xml.parsers.expat.ExpatError: not well-formed (invalid token): line 84, column 7
If the incoming frame buffer has GST_BUFFER_FLAG_DISCONT set this should
be preserved and set for the first output buffer too, like other
payloaders do.
Spotted with gst-validate-1.0 when adding integration tests for
rtpsession, a minimal test to reproduce the issue is:
$ gst-validate-1.0 videotestsrc num-buffers=1 ! rtpvrawpay ! identity ! fakesink
Starting pipeline
Pipeline started
warning : Buffer didn't have expected DISCONT flag333 speed: 1.000000 />
Detected on <identity0:sink>
Detected on <identity0:src>
Detected on <fakesink0:sink>
Description : Buffers after SEGMENT and FLUSH must have a DISCONT flag
Issues found: 1
=======> Test PASSED (Return value: 0)
This introduce a new signal on RTSession, on-sending-nacks is emited
right before the list of seqnums to be nacked are processed and
transformed into FB Nack. This allow implementing custom nacks
handling through another mechanism with APP feedback.
In order to do that, we now split the nacks registration from the actual
FB nack packet construction. We then try and add as many FB Nacks as
possible into the active packets and leave the remaining seqnums in the
RTPSource. In order to avoid sending outdated NACK later on, we save the
seqnum calculated deadline and cleanup the outdated seqnums before the
next RTCP send.
Fixes#583
Calling rtp_session_send_rtcp before marking the source as requiring a
pli/fir/nack meant the rtcp_thread could be scheduled and start running
before the source was updated. This meant the request would not be sent
early but instead was transmitted with the next regular RTCP packet.
Add test for nack generation.
If the current time is equal to the early rtcp time deadline, there is
no need to schedule a timer. This ensure that immediate feedback is
really immediate and simplify implementing unit tests with the test
clock, which stops perfectly on the timeout time.
This fix has been extracted from Pexip feature patch called
"rtpsession: Allow instant transmission of RTCP packets"
When used in combination with a rtponviftimestamp element
downstream, forwarding this flag ensures it gets correctly
serialized in the ONVIF header extension.
A missing colon after G_DEFINE_TYPE declaration was confusing gst-indent
and causing problem in the pre-commit hook.
Add the missing colon and fix the following function declaration to
follow the normal GStreamer style.
One comments in gst_rtp_session_chain_send_rtp_common() is referring to
groups in a buffer list, however this concept of "group" comes from
GStreamer 0.10 and does not exist anymore in GStreamer 1.0, so update the
comment to refer to buffers instead.
The update_receiver_stats() function is called also when sending packets
in rtp_source_send_rtp(), and sending packets may happen using a buffer
list rather than individual buffers.
So update the stats using the actual number of packets sent.
NOTE: this is fine for the receive path too (rtp_process_send_rtp)
because the receive path does not support buffer lists and
pinfo->packets would always be equal to 1 in this case.
This is needed for the case you don't know in advance all the sessions
you will be using, but would like to place all the related AUX element
in the same GstBin. As per current implementation, each time an sender
AUX bin is requested and returned, RTPBin will walk the src pads and
create sessions for these pads.
In the current implementation, if a src pad already have a sessions, it
returns an error and stops. As a side effect, if an AUX bin is reused in
a following AUX bin request, it can only work if the pads are created on
the last request.
This change simply relax the restriction in order to keep walking, and
just ensure that all newly created pads have a sessions.
Need to respect return of gst_video_guess_framerate() to ensure
non-zero denominator.
This patch is to fix below error with an abnormal (but has valid frame) file.
(gst-play-1.0:17940): GStreamer-CRITICAL **: passed '0' as denominator for `GstFraction'
This problem was found in Test. 2 of the YouTube 2018 EME
tests[1]. The code was accidentally not finding an mp4a's esds atom in
the sample description table when the stream was encrypted. It assumed
that if the stream is protected, then only an enca atom will be found
here. What happens with YouTube is they often provide protected
content with a few seconds of clear content, and then switch to the
encrypted stream.
The failure case here was an incorrect codec_data field being sent
into aacparse. The advertisement of stereo audio @ 44.1kHz for the
mp4a (unprotected) stream was incorrect. As usual, the esds contained
the real values here which were mono at 22050 Hz.
Here's what the MP4 tree looks like for these types of files,
demonstrating why the code was making a wrong assumption (or maybe
YouTube is being unusual),
[ftyp] size=8+16
...
[moov] size=8+1571
...
[trak] size=8+559
...
[stsd] size=12+234
entry-count = 2
[enca] size=8+147
channel_count = 2
sample_size = 16
sample_rate = 44100
[esds] size=12+27
...
...
[mp4a] size=8+67
channel_count = 2
sample_size = 16
sample_rate = 44100
[esds] size=12+27
...
In addition to fixing this, the checks for esds atoms in mp4a and mp4v
have been made symmetrical. While I haven't seen a test case for video
with the same problem, it seemed better to make the same checks. This
also fixes a crash reported from another user[2], they also noted the
asymmetry with mp4v and mp4a.
[1] https://yt-dash-mse-test.commondatastorage.googleapis.com/unit-tests/2018.html?test_type=encryptedmedia-test
[2] https://gitlab.freedesktop.org/gstreamer/gst-plugins-good/issues/398
This can happen in various error cases that could happen between the
creation of the element in question and the adding to the rtspsrc.
It causes an ugly critical warning right now but is otherwise harmless.
The imagefreeze element can be handy for benchmarking downstream
elements because it re-uses the same buffer memory and introduces less
overhead compared to always creating new frames with videotestsrc.
However it's not possible to make imagefreeze send EOS when using
gst-launch-1.0.
Add a num-buffers property to make it look more like a source in the
above scenario.
In commit 28e5f9098 (rtpbin: use PacketInfo for the sender, 2013-09-13)
the rtp_source_send_rtp signature changed but the documentation was not
adjusted to match the new one.
Update the documentation to match the function signature.
Some functions now accept a generic 'gpointer data' parameter because
they can work either on a single buffer or a buffer list.
However the comments were still referring to the old 'GstBuffer *buffer'
parameter, so update the comments to match the actual functions
signature.
So far we assumed that if all sources are bye, this meant we needed to
send an EOS on the RTCP sink. The problem is that this case may happens
if we only had one internal source and it detected a collision.
So now we limit the EOS forwarding to when there is a send_rtp_sink pad
and that this pad has received EOS. We don'tcheck the recv_rtp_sink
since the code does not wait for the bye to be send before sending EOS
to the RTCP src pad.
RF64 encode support was added to wavenc quite some time
ago, but not declared in wavparse. It seems wavparse can
decode it though, so add it to the sink pad.
The RF64 support was added in
https://bugzilla.gnome.org/show_bug.cgi?id=735627
This is useful when implementing custom retransmission mechanism like
RIST to prevent RTCP from being produces for the retransmitted SSRC.
This would also be used in general for various purpose when customizing
an RTP base pipeline.
If it goes over 2^15 packets, it will think it has rolled over
and start dropping all packets. So make sure the seqnum distance is not too big.
But let's not limit it to a number that is too small to avoid emptying it
needlessly if there is a spurious huge sequence number, let's allow at
least 10k packets in any case.
Recent changes in ccextractor were attaching timecode meta to the closed
caption track. We shouldn't write timecode information for the closed
caption trak.
And let it the oportunity to get its other pad linked
Example:
```
$ gst-launch-1.0 uridecodebin uri=file:///home/thiblahute/gst-validate.save/gst-integration-testsuites/testsuites/../medias/defaults/flv/819290236.flv caps=audio/x-raw expose-all-streams=FALSE ! fakesink
Setting pipeline to PAUSED ...
Pipeline is PREROLLING ...
ERROR: from element /GstPipeline:pipeline0/GstURIDecodeBin:uridecodebin0/GstDecodeBin:decodebin0/GstFlvDemux:flvdemux0: Internal data stream error.
Additional debug info:
../subprojects/gst-plugins-good/gst/flv/gstflvdemux.c(2760): gst_flv_demux_loop (): /GstPipeline:pipeline0/GstURIDecodeBin:uridecodebin0/GstDecodeBin:decodebin0/GstFlvDemux:flvdemux0:
streaming stopped, reason not-linked (-1)
ERROR: pipeline doesn't want to preroll.
Setting pipeline to NULL ...
Freeing pipeline ...
```
Modify the caps string to allow width and height greater than 4096.
There is no need to restrict it since the matroska format allows the
width and height values to be up to eight bytes long, and this also
applies to the webm subset of the format.
Fixes https://gitlab.freedesktop.org/gstreamer/gst-plugins-good/issues/550
When multiple nals are aggrgated, the marker bit should be associated only
with the last NAL of the packet. Otherwise we may break rendering in with
AU alignment.
And also add a property for setting this. By default it has the same
value as the metadatacreator metadata.
Various software is using encoder instead of metadatacreator, others are
using them both for different purposes. As such it's useful to have
support for setting both here.
Blocking in change_state() is a recipe for disaster, even more so if
we wait for another thread that also calls into various element API and
could then lead to deadlocks on e.g. the state lock.
EA608 closed caption tracks are a bit special in that each sample
can contain CCs for multiple frames, and CCs can be omitted and have to
be inferred from the duration of the sample then.
As such we take the framerate from the (first) video track here for
CEA608 as there must be one CC byte pair for every video frame
according to the spec.
For CEA708 all is fine and there is one sample per frame.
The duration field being a uint64, is stored in 8 bytes, not 4. So the offset of
the following field, language code, needs to be updated accordingly so that the
parsed language code is not garbage.
The documentation of "port-range" implies that passing NULL should be
valid, but currently it is not. Without this check, the sscanf() call
will crash.
This reverts commit dcd3ce9751.
This functionality was implemented for gstopenwebrtc, but it
turned out this was not actually needed for webrtc bundling
support, as shown in webrtcbin. It also doesn't correspond
to any standards.
This is an API break, but nothing should actually depend on
this, at least not for its initial purpose.
Changes in rtpbin.c were reverted manually, to preserve some
refactoring that had occurred in the original commit.
Fixes#537
This macro is not longer used. It was secretly checking if that nal was
a slice, and confusingly name to that one may think it was checking if
the nal is an AUD.
The code was reading the timestamp from the adapter before pushing the
new buffer into it. As a side effect, if the adapter was empty, we'd end
up using an older timestamp. In alignment=au, it means that all
timestamp was likely one frame in the past, while in alignment=nal, with
multiple slices per frame, the first slice would have the timestamp of
the previous one.
The marker bit is used for efficient decoding. The assumption that
it should be set on the AUD is wrong, since the AUD is conceptually
starts the frame, while the marker is to indicate the end.
So properly set the marker bit as soon as we know we are ending an
AU and also whenever upstream have set the GST_BUFFER_FLAG_MARKER
flag.
The code was reading the timestamp from the adapter before pushing the
new buffer into it. As a side effect, if the adapter was empty, we'd end
up using an older timestamp. In alignment=au, it means that all
timestamp was likely one frame in the past, while in alignment=nal, with
multiple slices per frame, the first slice would have the timestamp of
the previous one.
The marker bit is used for efficient decoding. The assumption that
it should be set on the AUD is wrong, since the AUD is conceptually
starts the frame, while the marker is to indicate the end.
So properly set the marker bit as soon as we know we are ending an
AU and also whenever upstream have set the GST_BUFFER_FLAG_MARKER
flag.
Don't allow external encoder to use one of the reserved NAL type
implicated in NAL aggreation. These out-of-spec NAL types, if passed
from the outside world will lead to an invalid RTP payload being
created.
When the EOS event is received, run all timers immediately and avoid
pushing the EOS downstream before this has been run. This ensures that
the lost packet statistics are accurate.
After EOS is received, it is pointless to wait for further events,
specially waiting on timers. This patches fixes two cases where we could
wait instead of returning GST_FLOW_EOS and trigger a spin of the loop
function when EOS is queued, regardless if this EOS is the queue head or
not.
stream.segment should be updated with the values of the current edit
list, also when a new `moov` is received. Unfortunately this was not
being the case because of an early return.
As a consequence of this bugs, no end of movie clipping was being
performed on the new moov and no segment event was being emitted.
When performing stream switching (e.g. in MSE) the new moov may have a
different edit list. This is often the case when switching between
baseline H.264 (which lacks B-frames) and more demanding profiles. For
this reason it's important to emit a new segment in order to be able
to get matching stream times.
This patch moves the initialization of QtDemuxStream.segment from
gst_qtdemux_add_stream() to _create_stream(). This ensures the segment
is always initialized when the stream is created.
Otherwise the segment format is left as GST_FORMAT_UNDEFINED in the case
were a track is reparsed and qtdemux_reuse_and_configure_stream() is
called instead of gst_qtdemux_add_stream(). (See
qtdemux_expose_streams() in the non streams-aware case.)
This is an extra internal recurisve lock use to avoid having to take
both sink pad streams lock all the time. This patch renamed it
INTERLNAL_STREAM_LOCK/UNLOCK() to avoid confusion with possible upstream
GST_PAD API.
This reverts "6f3734c305 rtpssrcdemux: Only forward stick events while
holding the sinkpad stream lock" and actually hold on the internal
stream lock. This prevents in some needed case having a second
streaming thread poping in and messing up event ordering.
While forwarding serialized event, we use gst_pad_forward() function.
In the forward callback (GstPadForwardFunction) we always return
TRUE. Returning true there will stop the dispatching procedure. As a
side effect, only one events is receiving the events. This breaks
when sending EOS from the applicaiton, it also breaks the latency
tracer.
This patch enables matroskademux to receive seeks before it reaches
GST_MATROSKA_READ_STATE_DATA.
Closes https://gitlab.freedesktop.org/gstreamer/gst-plugins-good/issues/514
This also enables receiving seeks in the element READY state.
When such a seek is received, it is stored to be later handled when
GST_MATROSKA_READ_STATE_DATA is reached.
Reset RTPSession when rtpsession changes state from PAUSED to READY.
Without this change, a stored last_rtptime in RTPSource could interfere
with RTP timestamp generation in RTCP Sender Report.
Fixes#510
If ctts (CompositionOffsetBox) has larger sample_offset
(offset between PTS and DTS) than (2 * duration) of the stream,
assume the ctts box to be corrupted and ignore the box.
https://bugzilla.gnome.org/show_bug.cgi?id=797262
This fixes a bug where in some files mehd.fragment_duration is one unit
less than the actual duration of the fragmented movie, as explained below:
mehd.fragment_duration is computed by scaling the end timestamp of
the last frame of the movie in (in nanoseconds) by the movie timescale.
In some situations, the end timestamp is innacurate due to lossy conversion to
fixed point required by GstBuffer upstream.
Take for instance a movie with 3 frames at exactly 3 fps.
$ gst-launch-1.0 -v videotestsrc num-buffers=3 \
! video/x-raw, framerate="(fraction)3/1" \
! x264enc \
! fakesink silent=false
dts: 999:59:59.333333334, pts: 1000:00:00.000000000, duration: 0:00:00.333333333
dts: 999:59:59.666666667, pts: 1000:00:00.666666666, duration: 0:00:00.333333334
dts: 1000:00:00.000000000, pts: 1000:00:00.333333333, duration: 0:00:00.333333333
The end timestamp is calculated by qtmux in this way:
end timestamp = last frame DTS + last frame DUR - first frame DTS =
= 1000:00:00.000000000 + 0:00:00.333333333 - 999:59:59.333333334 =
= 0:00:00.999999999
qtmux needs to round this timestamp to the declared movie timescale, which can
ameliorate this distortion, but it's important that round-neareast is used;
otherwise it would backfire badly.
Take for example a movie with a timescale of 30 units/s.
0.999999999 s * 30 units/s = 29.999999970 units
A round-floor (as it was done before this patch) would set fragment_duration to
29 units, amplifying the original distorsion from 1 nanosecond up to 33
milliseconds less than the correct value. The greatest distortion would occur
in the case where timescale = framerate, where an entire frame duration would
be subtracted.
Also, rounding is added to tkhd duration computation too, which
potentially has the same problem.
https://bugzilla.gnome.org/show_bug.cgi?id=793959
... before the old streams is not exposed yet for MSS stream.
In case of DASH, newly configured streams will be exposed
whenever demux got moov without delay.
Meanwhile, since there is no moov box in MSS stream,
the caps will act like moov. Then, there is delay for exposing new pads
until demux got the first moof.
So, following scenario is possible only for MSS but not for DASH,
STREAM-START -> CAPS -> (configure stream but NOT EXPOSED YET)
-> STREAM-START-> CAPS (configure stream again).
In above scenario, we can reuse old stream without any stream reconfigure.
https://bugzilla.gnome.org/show_bug.cgi?id=797239
Apart from the obvious drawbacks of hardcoding, the drawback here was
that, if we subtracted 2 frames (instead of 2.6) from the target running
time, we'd request the next keyframe a bit too far into the future,
which would make our files split at the wrong position.
https://bugzilla.gnome.org/show_bug.cgi?id=797293
Flv does not support various channels in AAC stream format, for example
flvdemux detect an audio channels of 2(stereo) when the AAC really is 1(mono).
https://bugzilla.gnome.org/show_bug.cgi?id=797275
Flv does support changing the stream type and stream properties
after the headers were started to be written, and for example H264
codec_data changes can be supported.
https://bugzilla.gnome.org/show_bug.cgi?id=797256
For drop-frame framerates, when the expected next max timecode wraps
around at the end of the day, we have to subtract the offset of the
daily jam, otherwise we end up with a duration that's a few frames too
long.
https://bugzilla.gnome.org/show_bug.cgi?id=797270
This commit:
1. Reads the WebM and Matroska ContentEncryption subelements.
2. Creates a GST_PROTECTION event for each ContentEncryption, which
will be sent before pushing the first source buffer.
The DRM system id field in this event is set to GST_PROTECTION_UNSPECIFIED_SYSTEM_ID,
because it isn't specified neither by Matroska nor by the WebM spec.
3. Reads the protection information of encrypted Block/SimpleBlock and
extracts the IV and the partitioning format (subsamples).
4. Creates the metadata protection for each encrypted Block/SimpleBlock,
with those informations: KeyID (extracted from ContentEncryption element),
IV and partitioning format.
5. Adds a new caps for WebM encrypted content named "application/x-webm-enc",
with the following new fields:
"encryption-algorithm": The encryption algorithm used.
values: "None", "DES", "3DES", "Twofish", "Blowfish", "AES".
"encoding-scope": The field that describes which Elements have been modified.
Values: "frame", "codec-data", "next-content".
"cipher-mode": The cipher mode used in the encryption.
Values: "None", "CTR".
https://bugzilla.gnome.org/show_bug.cgi?id=765275
Strip ADTS headers if we detect any, apparently some Sony cameras
send AAC with ADTS headers. We could also change the stream-format
in the output caps, but that would be unexpected to pipeline builders
and would not exactly be backwards compatible.
qtdemux_update_streams() is only ever called after checking
`qtdemux->streams_aware` is TRUE. There is no need to check for that
condition again.
`qtdemux->streams_aware` is only modified when the demuxer is
hard-resetted, which is mutually exclusive with demuxing, so it cannot
be modified during the call.
https://bugzilla.gnome.org/show_bug.cgi?id=797191
Currently matroskademux does not emit no-more-pads until the first
Cluster is parsed, even though the Tracks have already been parsed and
from that point on there can be no more tracks.
This is important in MSE because the browser needs to know when the MSE
initialization segment has been completely parsed so that it can expose
the tracks to the user. Some applications depend on this been done
before they feed frames to the demuxer.
As a consequence, historically WebKit has relied on hacks such as
listening to the `pad-added` event, which made impossible to support
multiple tracks in the same file. Let's fix that.
https://bugzilla.gnome.org/show_bug.cgi?id=797187
This patch allows matroskademux to parse a second Tracks element,
erroring out if the tracks are not compatible (different number, type or
codec) and emitting new caps and tag events should they have changed.
https://bugzilla.gnome.org/show_bug.cgi?id=793333
This splits gst_matroska_demux_add_stream() into:
* gst_matroska_demux_parse_stream(): will read the Matroska bytestream
and fill a GstMatroskaTrackContext.
* gst_matroska_demux_parse_tracks(): will check there are no repeated
tracks.
* gst_matroska_demux_add_stream(): creates and sets up the pad for the
track.
https://bugzilla.gnome.org/show_bug.cgi?id=793333
