It generally makes not much sense to configure it for all pads/traks at
once as this value is usually different for each of them. As such, add a
new property on the pads in addition to the existing property on the
whole muxer.
https://bugzilla.gnome.org/show_bug.cgi?id=792649
We can't handle recvonly streams, sendonly streams are perfectly fine.
The direction is the one from the point of view of the SDP offerer
(i.e. the RTSP server), and a recvonly stream would be one where the
server expects us to send media.
RFC 3264, section 5.1:
If the offerer wishes to only send media on a stream to its peer, it
MUST mark the stream as sendonly with the "a=sendonly" attribute.
This is mixed up in the ONVIF streaming specification examples, but
actual implementations and conformance tools seem to not care at all
about the attributes.
https://bugzilla.gnome.org/show_bug.cgi?id=792376
Raw AAC streams might have very small frames, e.g. 6 byte frames
when encoding silence. These frames are then smaller than aacparse's
default min_frame_size of 10 bytes (ADTS_MAX_SIZE).
When passthrough is disabled or aacparse has to output ADTS, GstBaseParse
will concatenate these short frames to the following frame before
handling them to aacparse, which processes each input buffer as a single
frame, producing bad output.
To avoid this problem, set the min_frame_size to 1 when receiving a raw
stream.
https://bugzilla.gnome.org/show_bug.cgi?id=792644
When the signal returns a floating reference, as its return type
is transfer full, we need to sink it ourselves before passing
it to gst_bin_add (which is transfer floating).
This allows us to unref it in bin_remove_element later on, and
thus to also release the reference we now own if the signal
returns a non-floating reference as well.
As we now still hold a reference to the element when removing it,
we also need to lock its state and setting it to NULL before
unreffing it
Also update the request_aux_sender test.
https://bugzilla.gnome.org/show_bug.cgi?id=792543
TOC support in mastroskamux has been deactivated for a couple of years. This commit updates it to recent GstToc evolutions and introduces toc unit tests for both matroska-mux and matroska-demux.
There are two UIDs for Chapters in Matroska's specifications:
- The ChapterUID is a mandatory unsigned integer which internally refers to a given chapter. Except for title & language which use dedicated fields, this UID can also be used to add tags to the Chapter. The tags come in a separate section of the container.
- The ChapterStringUID is an optional UTF-8 string which also uniquely refers to a chapter but from an external perspective. It can act as a "WebVTT cue identifier" which "can be used to reference a specific cue, for example from script or CSS".
During muxing, the ChapterUID is generated and checked for unicity, while the ChapterStringUID receives the user defined UID. In order to be able to refer to chapters from the tags section, we maintain an internal Toc tree with the generated ChapterUID.
When demuxing, the ChapterStringUIDs (if available) are assigned to the GstTocEntries UIDs and an internal toc mimicking the toc is used to keep track of the ChapterUIDs and match the tags with the appropriate GstTocEntries.
https://bugzilla.gnome.org/show_bug.cgi?id=790686
If we saw empty segments, we previously unconditionally pushed a
GAP event downstream regardless of the duration of that empty
segment.
In order to avoid issues with initial negotiation of downstream elements
(which would negotiate to something before receiving any data due to
that initial GAP event), check if there's at least a second of difference
(like we do for other GAP-related checks in qtdemux) before
deciding to push a GAP event downstream.
Otherwise baseparse will incrementally send us bigger buffers until the
full header size is reached, which is not only pointless but also means
that baseparse will reallocate and copy into a bigger buffer for every
input buffers. In pull mode that's done in 64kb increments, in push mode
usually in much smaller increments, causing a lot of overhead for
example when parsing high-quality coverart.
When receiving a seek event, check whether we can actually seek based
on the information the server provided.
Also add more documentation on what the seekable field means
If a reserved-max-duration is set, we should always track
and update the reserved-duration-remaining estimate, even
if we're not sending periodic moov updates downstream for
full robust muxing.
If the use-robust-muxing property is set, check if the
assigned muxer has reserved-max-duration and
reserved-duration-remaining properties, and if so set
the configured maximum duration to the reserved-max-duration
property, and monitor the remaining space to start
a new file if the reserved header space is about to run out -
even though it never ought to.
Switching to a new fragment because the input caps have
changed didn't properly end the previous file. Use the normal
EOS sequence to ensure that happens. Add a test that it works.
Only for byte-stream or hev1. For hvc1 the SPS/PPS are in the
caps as codec_data field and in this case they shouldn't be in
the stream data as well. The output caps should be updated with
the new codec_data if needed, for hvc1.
We keep the boolean byte_stream around since it's nicer for
readability and most of the code just cares about byte_stream
or not. This is useful for future-proofing the code for when
we add support for hev1 output as well.
This would happen if input is byte-stream with four-byte
sync markers instead of three-byte ones. The code that
scans for sync markers will place the start of the NALU
on the third-last byte of the NALU sync marker, which
means that any additional zeros may be counted as belonging
to the previous NALU instead of being part of the next sync
marker. Fix that so we don't send VPS/SPS/PPS with trailing
zeros in this case.
See https://bugzilla.gnome.org/show_bug.cgi?id=732758
There is no difference between pushing out a buffer directly
with gst_rtp_base_depayload_push() and returning it from the
process function. The base class will just call _depayload_push()
on the returned buffer as well.
So instead of marshalling buffers through three layers and back,
just push them from one place in handle_nal() and always return
NULL from the process vfunc. This simplifies the code a little.
Also rename _push_fragmentation_unit() to _finish_fragmentation_unit()
for clarity. Push sounds like it means being pushed out, whereas
it might just be pushed into an adapter.
This change has the side-effect that multiple NALs in a single STAP
(such as SPS/PPS) may no longer be pushed out as a single buffer if
we output NALs in byte-stream format (i.e. not aggregate AUs), but
that shouldn't really make any difference to anyone.
This would happen if input is byte-stream with four-byte
sync markers instead of three-byte ones. The code that
scans for sync markers will place the start of the NALU
on the third-last byte of the NALU sync marker, which
means that any additional zeros may be counted as belonging
to the previous NALU instead of being part of the next sync
marker. Fix that so we don't send SPS/PPS with trailing
zeros in this case.
https://bugzilla.gnome.org/show_bug.cgi?id=732758
