When the sub-class claims a program for later freeing, make
sure it's not left in the hash table, or it can cause crashes on shutdown.
Make sure tsdemux frees any program it has kept around at shutdown
if it wasn't freed already.
https://bugzilla.gnome.org/show_bug.cgi?id=763503
In some cases, the PTS might be smaller than the first observed PCR
value which causes element to apply wraparound leading to bogus
timestamp. To solve this, we only apply it if the PTS-PCR difference is
greater that 1 second to be sure that it's a real wraparound.
Moreover, using unsigned 32 bits values to handle wrapover could end up
with bogus value, so it use pts value to handle it.
Also, convert pcr time to gst time before comparing it to pts.
Since refpcr is expressed in PCR time base while pts is expressed in GStreamer
time.
https://bugzilla.gnome.org/show_bug.cgi?id=743259
This fixes a couple of issues regarding the output of (request)
per-program pads output:
We would never push out PAT sections (ok, that was one reallly stupid
mistake. I guess nobody ever uses this feature ...).
In the case where the PMT section of a program was bigger than one
packet, we would only end up pushing the last packet of that PMT. Which
obviously results in the resulting stream never containing the proper
(complete) PMT.
The problem was that the program is only started (in the base class)
after the PMT section is completely parsed. When dealing with single-program
pads, tsparse only wants to push the PMT corresponding to the requested
program (and not the other ones). tsparse did that check by looking
at the streams of the program...
... but that program doesn't exist for the first packets of the initial
PMT.
The fix is to use the base class program information (if it parsed the
PAT it already has some information, like the PMT PID for a given program)
if the program hasn't started yet.
In addition to the fact that it's a sane thing to do for multi-source
pad elements, it also avoids the situation where just using a request
pad (and not the main static pad) would result in the processing
stopping.
tsdemux is not able to handle negative playback rates.
But in mpegtsbase, the same check is not being done.
added a check to not handle negative rate while seeking unless
the same is handled upstream.
https://bugzilla.gnome.org/show_bug.cgi?id=758516
The order in which program switch must happen is:
1) drain all data on old pads (but don't push EOS)
2) add new pads (but don't push any data on them)
3) Push EOS and remove old pads
4) Start pushing data on new pads
There was one caveat in this implementation, which is that when
we activate a sparse pad (step 2) we would push a GAP event. The problem
is that, while being an event, it is actually *data*.
We therefore need to make sure pushing those GAP event is done at the step
we start pushing data.
https://bugzilla.gnome.org/show_bug.cgi?id=750402
Before we add any streams, make sure we drain all streams. This ensures
there's consistency that only "new" data will be pushed on buffers once
the new pads are added
https://bugzilla.gnome.org/show_bug.cgi?id=750402
When changing programs, the order of events needs to be the following:
* add pads from new program
* send EOS on old pads
* remove old pads
* emit 'no-more-pads'
Previously tsdemux was not doing that, and was first deactivating and
removing old pads before adding new ones.
We fix this by allowing subclasses of mpegtsbase to be able to handle
themselves the deactivation of programs. In this case tsdemux will
properly deactivate it once it has activated the new program.
https://bugzilla.gnome.org/show_bug.cgi?id=750402
If packet->payload_unit_start_indicator is true and pointer 0, there is no
discontinuity check. Therefore there could be a previous section not complete
that need to be cleared.
https://bugzilla.gnome.org/show_bug.cgi?id=758010
The values of channel_mapping are copied by gst_codec_utils_opus_create_caps ()
but it doesn't free or take ownership of the g_new0 allocated memory. This
needs to be freed before going out of scope.
CID 1338692
If tsdemux never receives data for a stream, the corresponding pad will never
be added and stream->active will remain FALSE. When the stream is removed, the
pad will not be unreffed and will be leaked.
https://bugzilla.gnome.org/show_bug.cgi?id=757873
The tsdemux latency should always be added to the minimum
latency (which is always a valid clock time value). The
"cleanup" in commit a1f709c2 made it so that it would not
be added if upstream reported 0 as minimum latency (as
e.g. udpsrc would). This broke playback of live mpeg-ts
streaming in some cases, leading to playback stutter due
to a too-small configured latency for the pipeline.
https://bugzilla.gnome.org/show_bug.cgi?id=751508
We only want to do a hard reset of the observations if we're working
with TIME segments in push mode. For BYTE segment we want to keep
the observations (in order to do seeks in push-mode).
When in push mode, we want to discard all previous observations from the
mpegtspacketizer when we get a DISCONT buffer.
This avoids trying to calculate bogus timestamps (estimating them using old
PCR observations).
We only do a hard reset in push-mode. In pull-mode we still need the observations
(in order to seek properly)
This is not public API, use g_assert() instead of
g_return_if_fail(), so that it's compiled out in
releases. It's only called from our code, with &foo.
The segment should start at first PTS, and the vairable name lower_pts
state so correctly. Though we where using the first DTS instead. This
could lead to small desynchronization of video stream.
https://bugzilla.gnome.org/show_bug.cgi?id=740575
Chinese broadcaster encapsulate AVS video codec into MPEG2-TS. They
use the stream_id 0x42 to identify AVS video streams. It should be noted
that this id is currently within the ISO reserved range, hence it's
utilisation is unofficial.
https://bugzilla.gnome.org/show_bug.cgi?id=727731
Timestamps should start at the segment start, rather than 0, so
we need to not subtract the first timestamp. This makes the sink
correctly account for running time when switching PMTs where a
stream starts not quite at zero, causing timing offsets that can
become noticeable and causing dropped frames after a few times.
A new program object is created to replace an existing one
in the programs hash table, so its refcount needs to match.
With the default of 0 refcount on creation, the next PAT
change will cause that refcount to be both incremented and
decremented (assuming the new PAT references that stream too),
which will cause the program to be destroyed.
https://bugzilla.gnome.org/show_bug.cgi?id=748412
If the stream which is about to be removed still has a ref on a tag list we
should drop it.
Fix a leak which was occasionally happening with the
validate.file.playback.change_state_intensive.tron_en_ge_aac_h264_ts scenario.
https://bugzilla.gnome.org/show_bug.cgi?id=748576
