Doing lazy conversion of PCR values doesn't work right
when a PCR discont is encountered. Instead, convert PCR
values to the continuous timestamp domain as soon as we
encounter them and store that instead.
Type cast has higher precedence than bitwise shift, so the third
argument will truncate to 8 bits and then shift right by 8 bits
resulting in constant zero.
https://bugzilla.gnome.org/show_bug.cgi?id=774293
This was a regression.
We only have a upstream-id via STREAM_START if we were in push-mode.
In pull-mode we need to create one.
Note: It would be good to eventually have that method (copied from
gst_pad_get_stream_id_internal()) public in the future
For each MpegTSBaseStream, we have a GstStream object which
subclasses can extend with information.
For each program a GstStreamCollection is created with all
GstStream from each stream.
When dealing with TIME-based input, the incoming stream could have
potentially changed completely.
In order to check whether it did or not, we need to re-check all sections
(PAT, PMT...). If it didn't, we will keep using the existing streams/pad,
and if it did we will act as if there was a program switch.
Fixes HLS streaming with decodebin3/playbin3
EAC3 bit streams shall be identified with a stream_type value of 0x87 when
transmitted as PES streams conforming to ATSC-published standards. It is specified
in ATSC Standard A/52.
https://bugzilla.gnome.org/show_bug.cgi?id=770528
The headers passed as parametter are relative to the build dir
basically "../subproject/gst-plugins-bad/gst-libs/gst/mpegts/XXX.h"
but that does not match what is needed at build time when building as
subproject, also we always add current dir as include_dir so we are
safe including directly.
And link mpegtsdemux against the 'math' library as it is needed.
https://github.com/mesonbuild/meson
With contributions from:
Tim-Philipp Müller <tim@centricular.com>
Matej Knopp <matej.knopp@gmail.com>
Jussi Pakkanen <jpakkane@gmail.com> (original port)
Highlights of the features provided are:
* Faster builds on Linux (~40-50% faster)
* The ability to build with MSVC on Windows
* Generate Visual Studio project files
* Generate XCode project files
* Much faster builds on Windows (on-par with Linux)
* Seriously fast configure and building on embedded
... and many more. For more details see:
http://blog.nirbheek.in/2016/05/gstreamer-and-meson-new-hope.htmlhttp://blog.nirbheek.in/2016/07/building-and-developing-gstreamer-using.html
Building with Meson should work on both Linux and Windows, but may
need a few more tweaks on other operating systems.
When draining a program, we might send a newsegment event on the pads
that are going to be removed (and then the pending data).
In order to do that, calculate_and_push_newsegment() needs to know
what list of streams it should take into account (instead of blindly
using the current one).
All callers to calculate_and_push_newsegment() and push_pending_data()
can now specify the program on which to act (or NULL for the default
one).
A simple fix for the problem of creating new pads with duplicate
names when switching program, easier than the alternative of
trying to work out which pads might persist and manage that.
See https://bugzilla.gnome.org/show_bug.cgi?id=758454
When the sub-class is delaying deactivation of the old program,
but it has the same program number as the new program, don't
overwrite the old program in the hash table and then steal
the new program back out of it. Instead, add the new program to
the hash table after handling removal of the old one.
When the sub-class claims a program for later freeing, make
sure it's not left in the hash table, or it can cause crashes on shutdown.
Make sure tsdemux frees any program it has kept around at shutdown
if it wasn't freed already.
https://bugzilla.gnome.org/show_bug.cgi?id=763503
In some cases, the PTS might be smaller than the first observed PCR
value which causes element to apply wraparound leading to bogus
timestamp. To solve this, we only apply it if the PTS-PCR difference is
greater that 1 second to be sure that it's a real wraparound.
Moreover, using unsigned 32 bits values to handle wrapover could end up
with bogus value, so it use pts value to handle it.
Also, convert pcr time to gst time before comparing it to pts.
Since refpcr is expressed in PCR time base while pts is expressed in GStreamer
time.
https://bugzilla.gnome.org/show_bug.cgi?id=743259
This fixes a couple of issues regarding the output of (request)
per-program pads output:
We would never push out PAT sections (ok, that was one reallly stupid
mistake. I guess nobody ever uses this feature ...).
In the case where the PMT section of a program was bigger than one
packet, we would only end up pushing the last packet of that PMT. Which
obviously results in the resulting stream never containing the proper
(complete) PMT.
The problem was that the program is only started (in the base class)
after the PMT section is completely parsed. When dealing with single-program
pads, tsparse only wants to push the PMT corresponding to the requested
program (and not the other ones). tsparse did that check by looking
at the streams of the program...
... but that program doesn't exist for the first packets of the initial
PMT.
The fix is to use the base class program information (if it parsed the
PAT it already has some information, like the PMT PID for a given program)
if the program hasn't started yet.
In addition to the fact that it's a sane thing to do for multi-source
pad elements, it also avoids the situation where just using a request
pad (and not the main static pad) would result in the processing
stopping.
tsdemux is not able to handle negative playback rates.
But in mpegtsbase, the same check is not being done.
added a check to not handle negative rate while seeking unless
the same is handled upstream.
https://bugzilla.gnome.org/show_bug.cgi?id=758516
The order in which program switch must happen is:
1) drain all data on old pads (but don't push EOS)
2) add new pads (but don't push any data on them)
3) Push EOS and remove old pads
4) Start pushing data on new pads
There was one caveat in this implementation, which is that when
we activate a sparse pad (step 2) we would push a GAP event. The problem
is that, while being an event, it is actually *data*.
We therefore need to make sure pushing those GAP event is done at the step
we start pushing data.
https://bugzilla.gnome.org/show_bug.cgi?id=750402
Before we add any streams, make sure we drain all streams. This ensures
there's consistency that only "new" data will be pushed on buffers once
the new pads are added
https://bugzilla.gnome.org/show_bug.cgi?id=750402
When changing programs, the order of events needs to be the following:
* add pads from new program
* send EOS on old pads
* remove old pads
* emit 'no-more-pads'
Previously tsdemux was not doing that, and was first deactivating and
removing old pads before adding new ones.
We fix this by allowing subclasses of mpegtsbase to be able to handle
themselves the deactivation of programs. In this case tsdemux will
properly deactivate it once it has activated the new program.
https://bugzilla.gnome.org/show_bug.cgi?id=750402
