Even if no new synchronization information is available.
This is necessary because the timestamp offset logic in rtpbin depends
on the base RTP time that is determined by the jitterbuffer, but this
changes all the time (especially in mode=slave) and the timestamp
offsets have to be updated accordingly. Doing so is especially important
if they're only determined by the RTP-Info, which never changes from the
very beginning.
The interval can be configured via the new min-sync-interval property.
Synchronization happens at least that often, but at most as often as the
old sync-interval property allows.
Both intervals are now based on the monotonic system clock.
Additionally, clean up synchronization code a bit, only emit either
inband NTP or RTCP SR synchronization at the same time, based on which
one has the more recent time information, and only emit RTP-Info
synchronization if it wasn't provided previously at the same time as the
NTP-based synchronization information.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6543>
There is generally no requirement to ignore RTCP SR if the RTP time of
the SR differs a lot from the last received RTP packet. The mapping
between RTP and NTP time stays valid until there was a stream reset, in
which case we wouldn't use that information anyway.
When using rtcp-sync-send-time=false the default of 1s difference can
easily be exceeded, e.g. if encoding of the stream after capture adds
more than 1s of latency.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6543>
Never is useful for some RTSP servers that report plain garbage both via
RTCP SR and RTP-Info, for example.
NTP is useful if synchronization should only ever happen based on RTCP
SR or NTP-64 RTP header extension.
Also slightly change the behaviour of always/initial to take RTP-Info
based synchronization into account too. It's supposed to give the same
values as the RTCP SR and is available earlier, so will generally cause
fewer synchronization glitches if it's made use of.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6543>
Instead of switching on the very first stream, require that all streams
have switched before switching to the different synchronization
mechanism.
Without this there will be a noticeable gap during the switch. E.g. when
going from RTP-Info to NTP-based association, first the first stream
only would get an offset, then the first two, ... then all of them.
Depending on the order of streams this will cause a lot of changes in
ts-offset during the transition.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6543>
Previously these parameters were randomly changed in the body of the
function to avoid having to declare a new variable, which made the code
very hard to follow. By marking them as const this won't be possible
anymore in the future.
Also the RTP clock-base (RTP time from RTSP RTP-Info) is an unsigned
64 bit integer as it's an extended RTP timestamp.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6543>
Both were entangled previously and very hard to follow what happens
under which conditions. Now as a very first step the code decides which
of the two cases it is going to apply, and then proceeds accordingly.
This also avoids calculating completely invalid values along the way and
even printing them int the debug output.
Also improve debug output in various places.
This shouldn't cause any behaviour changes.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6543>
This simplifies the code as it's a much simpler case than the normal
inter-stream synchronization, and interleaving it with that only
reduces readability of the code.
Also improve some debug output in this code path.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6543>
If we have constant duration buffers, set the duration on
outgoing buffers, like rtpmp4adepay does. This fixes
problems with (for example) muxers like mp4mux not writing
the duration of the final sample into the index.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6878>
During RTP-Info synchronization, clock_base was temporarily switched
from the actual clock-base to the base RTP time and then back some lines
later.
Instead directly work with the base RTP time. The comment about using a
signed variable for convenience doesn't make any sense because all
calculations done with the value are unsigned.
Similarly, rtp_clock_base was overridden with the rtp_delta when
calculating it, which was fine because it is not used anymore
afterwards. Instead, introduce a new variable `rtp_delta` to make this
calculation clearer.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6536>
It's not in the same period as the current RTP base time but always in
the very first period. This avoids using it again at a much later time.
The code in question is only triggered with rtcp-sync=rtp-info.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6536>
It is compared to other extended RTP timestamps all over rtpjitterbuffer
and since 4df3da3bab the initial extended RTP timestamp is not equal
anymore to the plain RTP time.
Continue passing a non-extended RTP timestamp via the `sync` signal for
backwards compatibility. It will always be a timestamp inside the first
extended timestamp period anyway.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6536>
When the buffer DTS is estimated based on arrival time at the
jitterbuffer (rather than provided on the incoming buffer itself),
it shouldn't be used for skew adjustment. The typical case is
packets being deinterleaved from a tunnelled TCP/HTTP RTSP stream,
and the arrival times at the jitter buffer are not well enough
correlated to usefully do skew adjustments.
This restores the original intended behaviour for the 'estimated dts'
path, that was broken years ago during other jitterbuffer refactoring.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6509>
If we can calculate timestamps for buffers, then set the duration
on outgoing buffers based on the number of samples depayloaded.
This can fix the muxing to mp4, where otherwise the last packet
in a muxed file will have 0 duration in the mp4 file.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6447>
When we're doing a state change from PLAYING to NULL, first we invoke
gst_rtspsrc_loop_send_cmd_and_wait (..., CMD_CLOSE, ...) during
PAUSED_TO_READY which will schedule a TEARDOWN to happen async on the
task thread.
The task thread will call gst_rtspsrc_close(), which will send the
TEARDOWN and once it's complete, it will call gst_rtspsrc_cleanup()
without taking any locks, which frees src->streams.
At the same time however, the state change in the app thread will
progress further and in READY_TO_NULL it will call gst_rtspsrc_stop()
which calls gst_rtspsrc_close() a second time, which accesses
src->streams (without a lock again), which leads to simultaneous
access of src->streams, and a segfault.
So the state change and the cleanup are racing, but they almost always
complete sequentially. Either the cleanup sets src->streams to NULL or
_stop() completes first. Very rarely, _stop() can start while
src->streams is being freed in a for loop. That causes the segfault.
This is unlocked access is unfixable with more locking, it just leads
to deadlocks. This pattern has been observed in rtspsrc a lot: state
changes and cleanup in the element are unfixably racy, and that
foundational issue is being addressed separately via a rewrite.
The bandage fix here is to prevent gst_rtspsrc_stop() from accessing
src->streams after it has already been freed by setting src->state to
INVALID.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6302>
The transport stream only returned the CAPS for the first matching PT entry
from the `ptmap`. Other SSRC with the same PT where not included. For a stream
which bundled multiple audio streams for instance, only the first SSRC was
knowed to the SSRC demux and downstream elements.
This commit adds all the `ssrc-` attributes from the matching PT entries.
The RTP jitter buffer can now find the CNAME corresponding its SSRC even if it
was not the first to be registered for a particular PT.
The RTP PT demux removes `ssrc-*` attributes cooresponding to other SSRCs
before pushing SSRC specific CAPS to downstream elements.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6119>
And also re-timestamp them with the current buffer's PTS.
Not doing so keeps the timestamps of event packets as
GST_CLOCK_TIME_NONE or the timestamp of the previous buffer, both of
which are bogus.
Making sure that (especially) the first packet has a valid timestamp
allows putting e.g. the NTP timestamp RTP header extension on it.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/5173>
Parse the speed and scale in the server's response
*before* the range, so that the range start/stop
are swapped (or not swapped) correctly based
on the server's actual chosen values. Otherwise,
the old rate from the segment is used - what the
last seek asked for, but not necessarily what
the server chooses.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6248>
After a flushing seek, rtspsrc doesn't reset the last_ret value for
streams, so might immediately shut down again when it resumes pushing
buffers to pads due to a cached `GST_FLOW_FLUSHING` result
Prevent a stored flushing value from immediately stopping
playback again by resetting pad flows before (re)starting
playback.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6137>
Because this depayloader may build several output buffers within one
process run we push them all into a GstBufferList and push them out at
once to make sure that each buffer gets notified about each header
extension.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/5378>
Because this depayloader may build several output buffers within one
process run we push them all into a GstBufferList and push them out at
once to make sure that each buffer gets notified about each header
extension.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/5378>
Because this depayloader may build several output buffers within one
process run we push them all into a GstBufferList and push them out at
once to make sure that each buffer gets notified about each header
extension.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/5378>
Because this depayloader may build several output buffers within one
process run we push them all into a GstBufferList and push them out at
once to make sure that each buffer gets notified about each header
extension.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/5378>
Because this depayloader may build several output buffers within one process
run we push them all into a GstBufferList and push them out at once to
make sure that each buffer gets notified about each header extension.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/5378>
In rtpbin we already systematically check for all property names
except latency, correct that.
In webrtcbin we need to check before trying to use the do-retransmission
property.
This is useful for the case where an element like identity gets passed
to rtpbin's request-jitterbuffer property, when the application wants
to use webrtcbin in an SFU situation, with no reordering and no added
latency
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6112>
Today when using the `splitmuxsrc` on a collection of files named as:
```
item0.mkv
item1.mkv
item2.mkv
[...]
item10.mkv
item11.mkv
[...]
```
You will get a continuous stream made in the order of:
```
item0.mkv -> item1.mkv -> item10.mkv -> item11.mkv -> [...]
```
You can fix this by having smarter names of the items:
```
item000.mkv
item001.mkv
item002.mkv
[...]
item010.mkv
item011.mkv
[...]
```
Will get you:
```
item000.mkv -> item001.mkv -> item003.mkv -> item004.mkv -> [...]
```
But, we could also "fix" the former case by using natural ordering when
comparing the files in gstsplitutils.c.
Fixes#2523
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/4491>
When level value is greater than 127, it was being clamped but this clamped
value was not the one being actually used. For level values greater than 127
this resulted in an incorrect value being used. As an example, a level value
of 187, after and'ed with 0x7F, it would result in 0x3B being reported as the
level value.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/5893>
The `GstFlowCombiner` is responsible for tracking the flow of each
stream and handle the overal flow return value. Without that, we
can end up with the following scenario:
- Audio+video stream
- Only the video stream is linked downstream
- The audio stream goes EOS, video doesn't yet
-> We update the Flow in the combiner with OK as all streams are not EOS
- Video goes EOS because downstream returned EOS
-> `qtdemux` returns `FLOW_OK` forever because the unlinked audio pad
has `last_flowret==FLOW_OK`
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/5724>
If this property is enabled then the jitterbuffer will do the normal PTS
calculations according to the configured mode instead of making use of
the RFC7273 media clock.
The timestamp calculated from the RFC7273 media clock will only be
stored in the reference timestamp meta, if addition of that meta is enabled.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/5512>
When this property is used, it is assumed that the system clock is
synced close enough to the media clock used by an RFC7273 stream.
As long as both clocks are at most a few seconds from each other this
will give the correct results and avoids having to create an actual
network clock that has to sync first.
If the system clock is actually synchronized to the media clock then
everything will behave exactly the same, otherwise the reference
timestamp meta will be correct but the buffer timestamps will be off by
the difference between the two clocks.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/5512>
Do more checks for clock equality than just checking pointers. The same
NTP/PTP clock might be used as pipeline clock but a new instance, so
instead also check what clock they are synced to.
Also handling setting / resetting of the media clock and pipeline clock
correctly by resetting the media clock's state accordingly.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/5512>
Because we treat raw audio chunks/samples as keyframes, they were interfering
with seek time adjustment.
Became apparent when the accompanying video stream was I-frame only,
for example ProRes.
Since raw audio streams can be seeked freely, it's fine to just ignore them here,
giving priority to the real keyframes in the video stream.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/4946>
With one regular image file path provided (without %05d),
the element was stuck in a dead loop counting the frames:
gst_image_sequence_src_count_frames
This allows to display any image file out of the element
for a given number of buffers.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/5471>
We were already converting the pad last timestamp to running time but
not the segment position.
This segment position is used by gst_aggregator_simple_get_next_time()
to compute the waiting time when aggregating.
Those waiting times were wrong in my live pipeline using the system
clock, resulting in the aggregator to never wait at all.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/5460>
scanlines->m1 = same line of the previous field
scanlines->t0 = line above of the current field
scanlines->b0 = line below of the current field
scanlines->mp = same line of the next field
Deinterlacing a field weaved frame:
When deinterlacing the top field, the next bottom field is available
(part of the same frame). but when deinterlacing the bottom field,
the next top field (part of the next frame) is not available and
scanlines->mp equals NULL.
In this case it's better to use greedy algorithm using the prevous field
(twice) rather then linear interpolation of the current field.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/5331>
If we end up with GST_CLOCK_TIME_NONE as running time for an RTP packet
then this can't be used for bitrate estimation, and also not for
constructing the next RTCP SR. Both would end up with completely wrong
values, and an RTCP SR with wrong values can easily break
synchronization in receivers.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/5329>
The timestamp offset can be negative, and it can be a bigger negative
number than the latency introduced by the rtpjitterbuffer so the overall
timeout offset can be negative.
Using the negative offset for calculating how many packets can still
arrive in time when encountering a lost packet in an equidistant stream
would then overflow and instead of considering fewer packets lost a lot
more packets are considered lost.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/5296>
This elements pass RTP packets along unchanged and appear as a RTP
payloader element.
This is useful, for example when using the gstreamer-rtsp-server
library, in the case where you are receiving RTP packets from a
different source and want to serve them over RTSP. Since the
gst-rtsp-server library expect the element marked as payX to be a RTP
payloader element and assumes certain properties are available.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/5204>
The hack enforcing strictly increasing timestamps was, according to the
code comments, because librtmp was confused with backwards timestamps.
rtmp2sink is not using librtmp as rtmpsink did, so this is no longer
required.
Also changing the timestamps is causing audio glitches when streaming to
Youtube.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/5212>
Fixes https://gitlab.freedesktop.org/gstreamer/gstreamer/-/issues/2771
This EOS branch exists so that if a seek with a stop is made, qtdemux
stops accepting bytes from the sink after the entire requested playback
range is demuxed, as otherwise we could keep download content that is
not being used.
This patch fixes two flaws that were present in that EOS check:
1) A comparison was made between track time and movie time without conversion.
This made the check trigger early in files with edit lists. This patch fixes
this by converting the track PTS to movie PTS (stream time) for the check.
2) To avoid sending a EOS prematurely when the segment stop is within a GOP and
B-frames are present, the check for EOS should only be done for keyframes. I
gather this was already the intention with the existing code, but because it
used `stream->on_keyframe` instead of the local variable `keyframe` the old
code was checking if the *previous* frame was a keyframe.
It's interesting to note that these two flaws in the old code mask each other
in most cases: the track PTS will have reached the movie end PTS, but EOS would
only be sent if the previous frame was a keyframe. A simple case where they
wouldn't mask each other, reproducing the bug, is a sequence of 3 frame GOPs
with structure I-B-P.
The following validateflow tests have been added to future-proof the
fix:
* validate.test.mp4.qtdemux_ibpibp_non_frag_pull.default
* validate.test.mp4.qtdemux_ibpibp_non_frag_push.default
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/5021>
We were checking if the tag list is writable, but it may actually be
shared through the same event (tee upstream or multiple consumers).
Fix a bug where multiple branches have a videoflip element checking the
taglist. The first one was changing the orientation back to rotate-0
which was resetting the other instances.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/5097>
Fix this pipeline where the tag list is not writable:
gst-launch-1.0 videotestsrc ! taginject tags="image-orientation=rotate-90" ! videoflip video-direction=auto \
! autovideosink
GStreamer-CRITICAL **: 12:34:36.310: gst_tag_list_add: assertion 'gst_tag_list_is_writable (list)' failed
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/4987>
Refusing an incoming segment in < GST_MATROSKA_READ_STATE_DATA should only be
done if the incoming segment is not in GST_FORMAT_TIME.
In GST_FORMAT_TIME, we are just storing the values and returning, so we can
invert the order of the checks.
Fixes proper segment propagation in matroska/webm DASH use-cases
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/3914>
... otherwise streams with constant size samples defined with a single
`sample_size` for all samples in the `stsz` box fall in the category
`chunks_are_samples` in `qtdemux_stbl_init`, overriding the actual
sample count.
`FOURCC_soun` would set this automatically for `compression_id == 0xfffe`,
however `compression_id` is read from the Audio Sample Entry box at an offset
marked as "pre-defined" in some version of the spec and set to 0 both by
GStreamer and FFmpeg for opus streams.
Considering the stream `sampled` flag is set explicitely by other fourcc
variants, doing so for opus seems consistent.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/4903>
The "Encapsulation of Opus in ISO Base Media File Format" [1] specifications,
§ 4.3.2 Opus Specific Box, indicates that data must be stored as big-endian.
In `build_opus_extension`, `gst_byte_writer_put*_le ()` variants were used,
causing audio streams conversion to Opus in mp4 to offset samples due to the
PreSkip field incorrect value (29ms early in our test cases).
[1] https://opus-codec.org/docs/opus_in_isobmff.html#4.3.2
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/4875>
When doing a segment seek, the base offset in the new segment
would be increased by segment.position which is basically the
timestamp of the last packet. This does not include the duration
of the last packet though, so might be slightly shorter than the
actual duration of the clip or the requested segment.
Increase the base offset by the segment duration instead when
accumulating segments, which is more correct as it doesn't cut
off the last frame and makes the effective loop segment duration
consistent with the actual duration returned from a duration
query.
In case a segment stop was specified it's also possible that
some data was sent beyond the stop that's necessary for decoding
so the base offset increment should be based on that then and
not on the timestamp of the last buffer pushed out.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/4604>
The muxer used a fixed value of 2 channels because the TR 102 366 spec
says they're to be ignored. However, the demuxer still trusted them,
resulting in bad caps.
Make the muxer fill in the correct channel count anyway (FFmpeg already
does) and make the demuxer ignore the value.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/4739>
Allow a project to use gstreamer-full as a static library
and link to create a binary without dependencies.
Introduce the option 'gst-full-target-type' to
select the build type, dynamic(default) or static.
In gstreamer-full/static build configuration gstreamer (gst.c)
needs the symbol gst_init_static_plugins which is defined
in gstreamer-full.
All the tests and examples are linking with gstreamer but the
symbol gst_init_static_plugins is only defined in the gstreamer-full
library. gstreamer-full can not be built first as it needs to know what plugins
will be built.
One option would be to build all the examples and tests after
gstreamer-full as the tools.
Disable tools build in subprojects too as it will be built at the end of
build process.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/4128>
