When closing the connection, unref the currently used sockets. This should close
them when not in use. We need to do this because else we cannot reconnect
anymore after a close, the connect function requires that the sockets are NULL.
Clear the GError after g_socket_connect tells us that the connection is pending.
If we don't do this, glib complains when we try to reuse the non-NULL GError
variable a little below.
Even if watch->messages->length is 0 there may still be some
data from a message that was only written partially at the
previous attempt stored in watch->write_data, so check for
that as well. We don't want to write data into the middle
of another message, which could happen when there wasn't
enough bandwidth.
https://bugzilla.gnome.org/show_bug.cgi?id=669039
Add private replacements for deprecated functions such as
g_mutex_new(), g_mutex_free(), g_cond_new() etc., mostly
to avoid the deprecation warnings. We'll change these
over to the new API once we depend on glib >= 2.32.
Replace g_thread_create() with g_thread_try_new().
Unlike linux, OSX wakes up select with POLLOUT (instead of POLLERR) when
connect() is done async and the connection is refused. Therefore always check
for the socket error state using getsockopt (..., SO_ERROR, ...) after a
connection attempt.
When closing rtspsrc the state change blocks until the polling in the
connection timeouts. This is because the second time we loop to read a
full message controllable is set to FALSE in the poll group, even though no
message is half read.
This can be avoided by not setting controllable to FALSE the poll group
unless we had begin to read a message.
Fixes#610916
Remove the android/ top dir
Fixe the Makefile.am to be androgenized
To build gstreamer for android we are now using androgenizer which generates the
needed Android.mk files.
Androgenizer can be found here:
http://git.collabora.co.uk/?p=user/derek/androgenizer.git
Make sure to use the PKG_CONFIG_PATH set at configure time instead of
just relying on an env-var set one. This makes sure both g-ir-compiler
and g-ir-scanner use the same PKG_CONFIG_PATH for determining include
paths etc.
We want to send the keealive message a little earlier than the timeout value
specifies. Scale this based on the value of the timeout instead of just assuming
5 seconds.
Because we should act before the rtsp server does a timeout, we
reduce the timeout-time with 5 seconds, this should be safe to always
keep te rtsp connection alive.
https://bugzilla.gnome.org/show_bug.cgi?id=633455
Force regeneration of marshal.[ch] files after prefix changes in
Makefile.am, to avoid build errors for those of us who don't
habitually make clean first.
When calling gobject-introspection scanner, make sure our own
freshly-built libs within the source tree (well, build dir) come
first in the PKG_CONFIG_PATH. May or may not help to make sure
that it doesn't pick up older external plugins-base libs (or
.gir files) from outside the source tree / build directory as
dependencies of the introspected lib instead of using the
stuff we just built in a sibling directory.
https://bugzilla.gnome.org/show_bug.cgi?id=623698
Catch more socket errors.
Rework how sockets are managed in the GSource, wake up the maincontext instead
of adding/removing the sockets from the source.
Add callback for when the tunnel connection is lost. Some clients (Quicktime
Player) close the POST connection in tunneled mode and reopen the socket when
needed.
See #612915
Point g-ir-scanner to the .la file of our library, which hopefully
makes it find the right dependencies in all cases (ie. our locally
built libgstreamer and not the system-installed one). This is also
how it's done in Gtk+ and how it's documented in the wiki, see
http://live.gnome.org/GObjectIntrospection/AutotoolsIntegrationFixes#603710.
Use new girdir and typlibdir from core .pc files, so we can figure
out the right includes to pass to the gobject-introspection tools,
whether core is installed in the same prefix as gobject-introspection
or in a different prefix or uninstalled. This also keeps us from adding
bogus paths to the includes that only work if core is uninstalled.
Also add some missing includes/pkgs where needed.
Since we no longer use an array of error messages, there is no reason
to clamp the error code, which allows us to simplify the code some more
and also to actually report the correct error code for unknown errors.
2 goals in the refactoring:
- Put the error messages closer to their enum values, so that it's easy
to see which error belongs to which value.
- Make gcc not complain with -Wformat-nonliteral
Be careful when allocating the amount of bytes specified in the Content-Length
because it can be an insanely huge value. Try to allocate the memory but fail
gracefully with a nice error when the allocation failed.
Use send() instead of write() so that we can pass the MSG_NOSIGNAL flags to
avoid crashing with SIGPIPE when the remote end is not listening to us anymore.
Fixes#601772
I also renamed glib_enum_prefix to glib_gen_prefix as we also use that for the
marshallers. Also rename the rtsp-marshal.list to work with the unified prefix.
gstrtspconnection.c:gst_rtsp_connection_receive() can hang when an error occured
on a socekt. Fix this problem by checking for error on 'other' socket after poll
return.
Fixes#596159
The new API to send messages using GstRTSPWatch will first try to send the
message immediately. Then, if that failed (or the message was not sent
fully), it will queue the remaining message for later delivery. This avoids
unnecessary context switches, and makes it possible to keep track of
whether the connection is blocked (the unblocking of the connection is
indicated by the reception of the message_sent signal).
This also deprecates the old API (gst_rtsp_watch_queue_data() and
gst_rtsp_watch_queue_message().)
API: gst_rtsp_watch_write_data()
API: gst_rtsp_watch_send_message()
With gst_rtsp_connection_set_http_mode() it is possible to tell the
connection whether to allow HTTP messages to be supported. By enabling HTTP
support the automatic HTTP tunnel support will also be disabled.
API: gst_rtsp_connection_set_http_mode()
The error_full callback is similar to the error callback, but allows for
better error handling. For read errors a partial message is provided to
help an RTSP server generate a more correct error response, and for write
errors the write queue id of the failed message is returned.
Rewrote read_line() to support LWS (Line White Space), the method used by
RTSP (and HTTP) to break long lines. Also added support for \r and \n as
line endings (in addition to the official \r\n).
From RFC 2068 section 4.2: "Multiple message-header fields with the same
field-name may be present in a message if and only if the entire
field-value for that header field is defined as a comma-separated list
[i.e., #(values)]." This means that we should not split other headers which
may contain a comma, e.g., Range and Date.
Due to the odd syntax for WWW-Authenticate (and Proxy-Authenticate) which
allows commas both to separate between multiple challenges, and within the
challenges themself, we need to take some extra care to split these headers
correctly.
Do not abort message parsing as soon as there is an error. Instead parse
as much as possible to allow a server to return as meaningful an error as
possible.
Remove any existing Session and Date headers before adding new ones
when sending a request. This may happen if the user of this code reuses
a request (rtspsrc does this when resending after authorization fails).
Do not use sizeof() on an array passed as an argument to a function and
expect to get anything but the size of a pointer. As a result only the
first 4 (or 8) bytes of the response buffer were initialized to 0 in
auth_digest_compute_response() which caused it to return a string which
was not NUL-terminated...
gst_rtsp_watch_queue_data() is similar to gst_rtsp_watch_queue_message()
but allows for queuing any data block for writing (much like
gst_rtsp_connection_write() vs. gst_rtsp_connection_send().)
API: gst_rtsp_watch_queue_data()
The base64 decoding in fill_bytes() expected the size of the read data to
be evenly divisible by four (which is true for the base64 encoded data
itself). This did not, however, take whitespace (especially line breaks)
into account and would fail the decoding if any whitespace was present.
Previously the messages_sent() callback was only called for messages
which had a CSeq, which excluded all data messages. Instead of using the
CSeq as ID, use a simple index counter.
People might queue messages from a thread other than the thread in which
the main context which this watch is attached is iterated from, so use
a GAsyncQueue instead of a GList, so g_list_append() doesn't trample
over list nodes just freed in the other thread. This just fixes issues
I've had with gst-rtsp-server. We might need more locking in various
places here.
We were returning a pointer to a stack variable with the resolved hostname,
which doesn't work.
return a copy of the resolved ip address instead.
Fixes#575256.
Free the key value before we remove the header item from the array. The item we
retrieved from the array is only valid until we remove it from the array.
Save the tunnelid in the connection. Add a method to retrieve the tunnelid so
that a server can store and match the id against other tunnel requests.
Fix the URI in the tunnel requests so that they contain the absolute uri and the
query string if any instead of just the hostname.
Transparently base64 decode the input stream when tunneling.
Add method to set the connection ip address so that it can be included in the
tunnel response.
Add method to connect the two tunnel requests.
Add two callbacks for the async mode to notify a tunnel start and tunnel
complete event.
Add method to reset the watch after the connection has been tunneled.
Various little refactoring to make more stuff reusable.
API: RTSP::gst_rtsp_connection_set_ip()
API: RTSP::gst_rtsp_connection_get_tunnelid()
API: RTSP::gst_rtsp_connection_do_tunnel()
API: RTSP::gst_rtsp_watch_reset()
Add support for tunneling RTSP over HTTP.
Fix documentation some more.
See also #573173.
API: RTSP:gst_rtsp_connection_is_tunneled()
API: RTSP:gst_rtsp_connection_set_tunneled()
Add transport define for RTSP tunneled over HTTP.
Parse rtsph:// uris as tunneled HTTP over TCP.
API: GstRTSPLowerTrans::GST_RTSP_LOWER_TRANS_HTTP
See also #573173.
Add gst_rtsp_connection_get_url() method.
Reserve space for 2 sockets, one for reading and one for writing. Use socket
pointers to select the read and write sockets. This should allow us to implement
tunneling over HTTP soon.
API: RTSP::gst_rtsp_connection_get_url()
Don't randomly call WSAStartup and WSACleanup but instead call the startup when
we create a connection and cleanup when we free it again. Because the internal
datastructure is refcounted, this should not cause any refcounting leaks when
the connection is managed correctly.
Fixes#562794.
