Reset last_timestamp_out when applying the output segment
change, to avoid decoder confusion over new timestamp timelines when
a seamless segment change happens.
Move some locks/unlocks to later when they're actually needed.
https://bugzilla.gnome.org/show_bug.cgi?id=734617
This fixes the reverse playback scenario when upstream is not fully
parsing the stream and does not send every keyframe chain separately
with the DISCONT flag on the keyframe.
To explain this, let's suppose we have this stream:
0 1 2 3 4 5 6 7 8
K K K
In most circumstances, the upstream parser will chain in the
decoder the buffers in the following order:
6 7 8 3 4 5 0 1 2
D D D
In this case, GstVideoDecoder will flush the parse queue every time
it receives discont (D) and we will eventually get in the output queue:
(flush here) 8 7 6 (flush here) 5 4 3 (flush here) 2 1 0
In case the upstream parser doesn't do this work, though,
GstVideoDecoder will receive the whole stream at once and will flush
the parse queue afterwards:
0 1 2 3 4 5 6 7 8
D
During the flush, it will look backwards for keyframes and will
decode in this order:
6 7 8 3 4 5 0 1 2
This is the same order that it would receive from upstream if
upstream was parsing and looking for the keyframes, only that now
there is no flushing of the output queue in between keyframes,
which will result in the output queue looking like this:
2 1 0 6 5 3 8 7 6
This will confuse downstream obviously and will play incorrectly.
This patch forces the decoder to flush the output queue every time
it picks a new keyframe to decode, so it will end up decoding 6 7 8
and then flushing before picking 3 for decoding, so the output will
get 8 7 6 before 6 5 3 and the video will play back correctly.
https://bugzilla.gnome.org/show_bug.cgi?id=734441
Fix gst_video_decoder_parse_available() to really parse any pending
source data that is still available in the adapter. This is a memory
optimization to avoid expansion of video packed added to the adapter,
but also a fix to EOS condition when the subclass parse() function
ultimately only needed to call into gvd_have_frame() and no additional
source bytes were consumed, i.e. gvd_add_to_frame() is not called.
This situation can occur when decoding H.264 streams in byte-stream/nal
mode for instance. A decoder always requires the next NAL unit to be
parsed so that to determine picture boundaries. When a new picture is
found, no byte is consumed (i.e. gvd_add_to_frame() is not called)
but gvd_have_frame() is called (i.e. priv->current_frame is gone).
Also make sure to avoid infinite loops caused by incorrect subclass
parse() implementations. This can occur when no byte gets consumed
and no appropriate indication (GST_VIDEO_DECODER_FLOW_NEED_DATA) is
returned.
https://bugzilla.gnome.org/show_bug.cgi?id=731974
Signed-off-by: Gwenole Beauchesne <gwenole.beauchesne@intel.com>
Buffer pool set_config() may return FALSE if requested configuration needed small
changes. Reget the config and try setting it again. This ensure we have a configured
pool if possible.
Videodecoder does late renegotiation, it will wait for the next
buffer before renegotiating its caps and bufferpool. It might happen
that downstream element switched from passthrough to non-passthrough
and sent a reconfigure upstream (that caused this renegotiation).
This downstream element will ask the video sink below for the bufferpool
with an allocation query and will get the same bufferpool that
videodecoder is holding, too.
When renegotiating, if videodecoder deactivates its bufferpool it
might be deactivating the bufferpool that some element downstream
is using and cause the pipeline to fail.
https://bugzilla.gnome.org/show_bug.cgi?id=727498
baseparse will reverse each GOP for us already, so the segment events can
be after our keyframe. Make sure to get it and all other relevant sticky
events before starting to decode.
For reverse playback, the segment event will only be pushed when
the first buffer is actually pushed. But for decoding frames and storing
those into the list to be pushed the output_segment.rate value is used
to determine if it is forward or reverse playback.
In case a previous segment event (or none) is in use it will mistakenly
think it is doing forward playback and push the buffers immediatelly and
try to clip buffers based on an old segment (or an uninitialized one, leading
to an assertion)
This patch fixes this by copying the segment earlier if on reverse playback
https://bugzilla.gnome.org/show_bug.cgi?id=721666
So that it avoids to send an allocation query twice.
One from an early call to gst_video_encoder_negotiate from a
subclass, then one from gst_video_encoder_allocate_output_frame.
Which means that previously gst_video_encoder_negotiate was not
clearing the GST_PAD_FLAG_NEED_RECONFIGURE even on success.
Fixes bug https://bugzilla.gnome.org/show_bug.cgi?id=719684
... so subclasses can release a frame all the way (also from frame list)
without having to pass through _finish_frame or _drop_frame.
The latter may not be applicable, or may or may not have already
been called for the frame in question.
See https://bugzilla.gnome.org/show_bug.cgi?id=693772
We could have allocation query before caps event and even without caps inside
the query. In such cases , the downstream can return a bufferpool object with
out actually configuring it. This feature is helpful to negotiate the bufferpool
with out knowing the output video format. For eg: some hardware accelerated
decoders can interpret the o/p video format only after it finishes the decoding
of one buffer at least.
https://bugzilla.gnome.org/show_bug.cgi?id=687183
This avoids triggering plenty of extra code/methods/overhead downstream when
we can just quickly check whenever we want to set caps whether they are
identical or not
https://bugzilla.gnome.org/show_bug.cgi?id=706600
Either there was a flush before that resets everything anyway,
or resetting would make us lose information we might need if
it's just a segment update.
