By passing `NULL` to `g_signal_new` instead of a marshaller, GLib will
actually internally optimize the signal (if the marshaller is available
in GLib itself) by also setting the valist marshaller. This makes the
signal emission a bit more performant than the regular marshalling,
which still needs to box into `GValue` and call libffi in case of a
generic marshaller.
Note that for custom marshallers, one would use
`g_signal_set_va_marshaller()` with the valist marshaller instead.
According to RFC3550 lower-level headers should be considered for
bandwidth calculation.
See https://tools.ietf.org/html/rfc3550#section-6.2 paragraph 4:
Bandwidth calculations for control and data traffic include
lower-layer transport and network protocols (e.g., UDP and IP) since
that is what the resource reservation system would need to know.
Fix the source data to accommodate that.
Assume UDPv4 over IP for now, this is a simplification but it's good
enough for now.
While at it define a constant and use that instead of a magic number.
NOTE: this change basically reverts the logic of commit 529f443a6
(rtpsource: use payload size to estimate bitrate, 2010-03-02)
If the conflict is detected when sending a packet, then also send an
upstream event to tell the source to reconfigure itself.
Also ignore the collision if we see more than one collision from the same
remote source to avoid problems on loops.
We recently added code to remove outdate NACK to avoid using bandwidth
for packet that have no chance of arriving on time. Though, this had a
side effect, which is that it was to get an early RTCP packet with no
feedback into it. This was pretty useless but also had a side effect,
which is that the RTX RTT value would never be updated. So we we stared
having late RTX request due to high RTT, we'd never manage to recover.
This fixes the regression by making sure we keep at least one NACK in
this situation. This is really light on the bandwidth and allow for
quick recover after the RTT have spiked higher then the jitterbuffer
capacity.
Right now, we may call on-new-ssrc after we have processed the first
RTP packet. This prevents properly configuring the source as some
property like "probation" are copied internally for use as a
decreasing counter. For this specific property, it prevents the
application from disabling probation on auxiliary sparse stream.
Probation is harmful on sparse streams since the probation algorithm
assume frequent and contiguous RTP packets.
This introduce a new signal on RTSession, on-sending-nacks is emited
right before the list of seqnums to be nacked are processed and
transformed into FB Nack. This allow implementing custom nacks
handling through another mechanism with APP feedback.
In order to do that, we now split the nacks registration from the actual
FB nack packet construction. We then try and add as many FB Nacks as
possible into the active packets and leave the remaining seqnums in the
RTPSource. In order to avoid sending outdated NACK later on, we save the
seqnum calculated deadline and cleanup the outdated seqnums before the
next RTCP send.
Fixes#583
Calling rtp_session_send_rtcp before marking the source as requiring a
pli/fir/nack meant the rtcp_thread could be scheduled and start running
before the source was updated. This meant the request would not be sent
early but instead was transmitted with the next regular RTCP packet.
Add test for nack generation.
If the current time is equal to the early rtcp time deadline, there is
no need to schedule a timer. This ensure that immediate feedback is
really immediate and simplify implementing unit tests with the test
clock, which stops perfectly on the timeout time.
This fix has been extracted from Pexip feature patch called
"rtpsession: Allow instant transmission of RTCP packets"
Some functions now accept a generic 'gpointer data' parameter because
they can work either on a single buffer or a buffer list.
However the comments were still referring to the old 'GstBuffer *buffer'
parameter, so update the comments to match the actual functions
signature.
This is useful when implementing custom retransmission mechanism like
RIST to prevent RTCP from being produces for the retransmitted SSRC.
This would also be used in general for various purpose when customizing
an RTP base pipeline.
Reset RTPSession when rtpsession changes state from PAUSED to READY.
Without this change, a stored last_rtptime in RTPSource could interfere
with RTP timestamp generation in RTCP Sender Report.
Fixes#510
Always wait with starting the RTCP thread until either a RTP or RTCP
packet is sent or received. Special handling is needed to make sure the
RTCP thread is started when requesting an early RTCP packet.
We want to wait with starting the RTCP thread until it's needed in order
to not send RTCP packets for an inactive source.
https://bugzilla.gnome.org/show_bug.cgi?id=795139
The code before copied GstStructure twice. The first time inside
gst_value_set_structure and the second time in g_value_array_append.
Optimized version does no copies, just transfers ownership to
GValueArray. It takes advantage of the fact that array has already
enough elements preallocated and the memory is zero initialized.
https://bugzilla.gnome.org/show_bug.cgi?id=795139
If obtain_internal_source() returns a source that is not internal it
means there exists a non-internal source with the same ssrc. Such an
ssrc collision should be handled by sending a GstRTPCollision event
upstream and choose a new ssrc, but for now we simply drop the packet.
Trying to process the packet further will cause it to be pushed
usptream (!) since the source is not internal (see source_push_rtp()).
https://bugzilla.gnome.org/show_bug.cgi?id=795139
If there is an external source which is about to timeout and be removed
from the source hashtable and we receive feedback RTCP packet with the
media ssrc of the source, we unlock the session in
rtp_session_process_feedback before emitting 'on-feedback-rtcp' signal
allowing rtcp timer to kick in and grab the lock. It will get rid of
the source and rtp_session_process_feedback will be left with RTPSource
with ref count 0.
The fix is to grab the ref to the RTPSource object in
rtp_session_process_feedback.
https://bugzilla.gnome.org/show_bug.cgi?id=795139
These are the sources we send from, so there is no reason to
report receive statistics for them (as we do not receive on them,
and the remote side has no knowledge of them).
https://bugzilla.gnome.org/show_bug.cgi?id=795139
When XR packet is detected, warning message leads to misunderstandings.
Until RFC3611 is implemented in gst-plugins-base, the level needs to
be downgraded to avoid confusion.
https://bugzilla.gnome.org/show_bug.cgi?id=789746
This debug statement is meant to print the time since the last (early)
RTCP transmission, not the last regular RTCP transmission (which also
happens to be set a few lines above to current_time, so the debug output
is just confusing)
Instead of sending EOS when a source byes we have to wait for
all the sources to be gone, which means they already sent BYE and
were removed from the session. We now handle the EOS in the rtcp
loop checking the amount of sources in the session.
https://bugzilla.gnome.org/show_bug.cgi?id=773218
