Implement 3 different cases for handling the SR:
1) we don't have enough timing information to handle the SR packet and
we need to wait a little for more RTP packets. In that case we keep
the SR packet around and retry when we get an RTP packet in the
chain function.
2) the SR packet has a too old timestamp and should be discarded. It is
labeled invalid and the last_sr is cleared.
3) the SR packet is ok and there is enough timing information, proceed
with processing the SR packet.
Before this patch, case 2) and 1) were handled in the same way,
resulting that SR packets with too old timestamps were checked over and
over again for each RTP packet.
1) sources that have sent BYE in the past cannot be senders, since
they would have timed out to being receivers in the meantime...
2) sources that have sent BYE are now being removed earlier inside
this function
If we are inserting a packet into the jitter queue we need to keep
looping through the items until the right position is found. Currently,
the code stops as soon as an event is found in the queue.
Regarding events, we should only move packets before an event if there
is another packet before the event that has a larger seqnum.
Fixes https://bugzilla.gnome.org/show_bug.cgi?id=730078
If two streams request a retranmission for the same SSRC, ignore the second
one if the first oen is less than one second old, otherwise time out the first
one and ignore the second.
As we now replace the local RTPSource on a conflict, it's no longer possible
to keep local conflicts in the RTPSource, so they instead need to be kept
in the RTPSession.
Also fix the rtpcollision test to generate multiple collisions instead of
one by change the address, as otherwise we detected that it was a single one.
Rework the packet queue so that the most common action (insert a packet
at the tail of the queue) goes very fast.
Report if a packet was inserted at the head instead of the tail so that
we can know when to retry _pop or _peek.
They are very confusing for people, and more often than not
also just not very accurate. Seeing 'last reviewed: 2005' in
your docs is not very confidence-inspiring. Let's just remove
those comments.
Make a new method to disable the jitterbuffer buffering.
Rework the update_estimated_eos() method. Calculate how much time
there is left to play. If we have less than the delay of the
jitterbuffer, we disabled buffering because we might never be able to
fill the complete jitterbuffer again.
If we receive an EOS event, disable buffering. We will drain the
buffer and eventually push the EOS event out.
When we reach the estimated NPT timeout and we didn't receive an EOS
event, make one and queue it so that it can be pushed.
Fixes https://bugzilla.gnome.org/show_bug.cgi?id=728017
When the internal-ssrc property changes, we want to send a reconfigure
upstream to make payloaders use the new suggested ssrc.
Using the internal-ssrc property to change the SSRC of a stream is not a
good idea and doesn't work when there are multiple senders, we want to
set the SSRC directly on the payloaders. Therefore, deprecate this
property.
Fixes https://bugzilla.gnome.org/show_bug.cgi?id=725361
Rework the logic to make buffering messages a little, make sure we
don't make the same message multiple times.
Consider the buffer full when EOS was received.
Fixes https://bugzilla.gnome.org/show_bug.cgi?id=728017
When we are buffering, we can't block and wait for the serialized query
to complete because the jitterbuffer will not try to forward the query
while buffering. Instead, just refuse the query.
It is possible that the DTS is invalid (when we receive RTP packets from
TCP, for example). As a fallback, use the reconstructed PTS value to
calculate the buffer level.
gstrtpjitterbuffer.c: In function 'gst_rtp_jitter_buffer_loop':
gstrtpjitterbuffer.c:2978:3: error: 'result' may be used uninitialized in this function
while (result == GST_FLOW_OK);
^
Several conditional statements perform comparison on RTP sequence
numbers without taking the sequence number rollover into account.
Instead, use the gst_rtp_buffer_compare_seqnum function to perform the
comparison.
https://bugzilla.gnome.org/show_bug.cgi?id=725159
recv_rtp_sink: allow proxying of the allocation query.
send_rtp_sink: allow proxying of caps and allocation. This allows us to
query caps downstream as well as get an allocator from downstream.
send_rtp_src: allow proxy of caps, this makes the caps query do
upstream.
See https://bugzilla.gnome.org/show_bug.cgi?id=723850
If the expected packet (do_next_seqnum is TRUE) is the one we requested
for retranmission earlier, do the logic to update the retransmission
statistics as well before setting up the timers for the next expected
packet.
Also reset the retransmission counter if the timer is reused for another
seqnum.
Add an accumulator that stops the signal emission as soon as a caps has
been retrieved. Otherwise the default handler would continue emitting
the signal and possibly overwrite the result with NULL again.
To do that, enqueue the EOS event to be sent from the srcpad task
thread and flush the queue right afterwards, so that no more rtx
buffers can be sent, even if there are more requests coming in.
Fixes https://bugzilla.gnome.org/show_bug.cgi?id=722370
