The order in which program switch must happen is:
1) drain all data on old pads (but don't push EOS)
2) add new pads (but don't push any data on them)
3) Push EOS and remove old pads
4) Start pushing data on new pads
There was one caveat in this implementation, which is that when
we activate a sparse pad (step 2) we would push a GAP event. The problem
is that, while being an event, it is actually *data*.
We therefore need to make sure pushing those GAP event is done at the step
we start pushing data.
https://bugzilla.gnome.org/show_bug.cgi?id=750402
Before we add any streams, make sure we drain all streams. This ensures
there's consistency that only "new" data will be pushed on buffers once
the new pads are added
https://bugzilla.gnome.org/show_bug.cgi?id=750402
When changing programs, the order of events needs to be the following:
* add pads from new program
* send EOS on old pads
* remove old pads
* emit 'no-more-pads'
Previously tsdemux was not doing that, and was first deactivating and
removing old pads before adding new ones.
We fix this by allowing subclasses of mpegtsbase to be able to handle
themselves the deactivation of programs. In this case tsdemux will
properly deactivate it once it has activated the new program.
https://bugzilla.gnome.org/show_bug.cgi?id=750402
If packet->payload_unit_start_indicator is true and pointer 0, there is no
discontinuity check. Therefore there could be a previous section not complete
that need to be cleared.
https://bugzilla.gnome.org/show_bug.cgi?id=758010
The values of channel_mapping are copied by gst_codec_utils_opus_create_caps ()
but it doesn't free or take ownership of the g_new0 allocated memory. This
needs to be freed before going out of scope.
CID 1338692
If tsdemux never receives data for a stream, the corresponding pad will never
be added and stream->active will remain FALSE. When the stream is removed, the
pad will not be unreffed and will be leaked.
https://bugzilla.gnome.org/show_bug.cgi?id=757873
The tsdemux latency should always be added to the minimum
latency (which is always a valid clock time value). The
"cleanup" in commit a1f709c2 made it so that it would not
be added if upstream reported 0 as minimum latency (as
e.g. udpsrc would). This broke playback of live mpeg-ts
streaming in some cases, leading to playback stutter due
to a too-small configured latency for the pipeline.
https://bugzilla.gnome.org/show_bug.cgi?id=751508
We only want to do a hard reset of the observations if we're working
with TIME segments in push mode. For BYTE segment we want to keep
the observations (in order to do seeks in push-mode).
When in push mode, we want to discard all previous observations from the
mpegtspacketizer when we get a DISCONT buffer.
This avoids trying to calculate bogus timestamps (estimating them using old
PCR observations).
We only do a hard reset in push-mode. In pull-mode we still need the observations
(in order to seek properly)
This is not public API, use g_assert() instead of
g_return_if_fail(), so that it's compiled out in
releases. It's only called from our code, with &foo.
The segment should start at first PTS, and the vairable name lower_pts
state so correctly. Though we where using the first DTS instead. This
could lead to small desynchronization of video stream.
https://bugzilla.gnome.org/show_bug.cgi?id=740575
Chinese broadcaster encapsulate AVS video codec into MPEG2-TS. They
use the stream_id 0x42 to identify AVS video streams. It should be noted
that this id is currently within the ISO reserved range, hence it's
utilisation is unofficial.
https://bugzilla.gnome.org/show_bug.cgi?id=727731
Timestamps should start at the segment start, rather than 0, so
we need to not subtract the first timestamp. This makes the sink
correctly account for running time when switching PMTs where a
stream starts not quite at zero, causing timing offsets that can
become noticeable and causing dropped frames after a few times.
A new program object is created to replace an existing one
in the programs hash table, so its refcount needs to match.
With the default of 0 refcount on creation, the next PAT
change will cause that refcount to be both incremented and
decremented (assuming the new PAT references that stream too),
which will cause the program to be destroyed.
https://bugzilla.gnome.org/show_bug.cgi?id=748412
If the stream which is about to be removed still has a ref on a tag list we
should drop it.
Fix a leak which was occasionally happening with the
validate.file.playback.change_state_intensive.tron_en_ge_aac_h264_ts scenario.
https://bugzilla.gnome.org/show_bug.cgi?id=748576
Such seeks are used to change playback rate and we do not want
to alter the position in that case, so we bypass the flush/seek
logic, and set things up so a new segment is scheduled to be
regenerated.
https://bugzilla.gnome.org/show_bug.cgi?id=735100
This will happen when the PMT changes, replacing streams with
new ones. In that case, we need to accumulate the running time
from the previous chain in the segment base.
https://bugzilla.gnome.org/show_bug.cgi?id=745102
Always update the segment and not only for accurate seeking and always
send a new segment event after seeks.
For non-accurate force a reset of our segment info to start from
where our seek led us as we don't need to be accurate
https://bugzilla.gnome.org/show_bug.cgi?id=743363
The flush is called on discont and we shouldn't output a new segment
each time a discont happens. So this commit remove the mark for a new
segment when flushing streams by propagating the 'hard' flag passed
on the flusing from the base class.
https://bugzilla.gnome.org/show_bug.cgi?id=743363
