In case of the videomark being partially or fully outside,
an error was bein thrown saying, mark width is more than video width.
And when the width, offset properties are set to maximum it resulted in crash.
Instead of throwing error, added logic to detect the mark
in case of partial visibility or dont show the mark when it is outside.
https://bugzilla.gnome.org/show_bug.cgi?id=743908
In case of the videomark being partially or fully outside, an error was being
thrown saying the mark width is more than video width. And when the width,
offset properties are set to maximum it resulted in crash. Instead of throwing
an error, add logic to detect the mark in case of partial visibility or don't
show the mark when it is outside.
https://bugzilla.gnome.org/show_bug.cgi?id=743908
Chinese broadcaster encapsulate AVS video codec into MPEG2-TS. They
use the stream_id 0x42 to identify AVS video streams. It should be noted
that this id is currently within the ISO reserved range, hence it's
utilisation is unofficial.
https://bugzilla.gnome.org/show_bug.cgi?id=727731
Value of res is reset to FALSE in each iteration of the while loop. We want to
conserve TRUE if any pad event succeeded until we arrive to done.
Also, buf is set to the value of *outbuf twice. Removing the first assignment
since the second one is outside of a conditional.
Like SPS/PPS they do contain information which will be needed to
decode the following data (as per definition of the flag)
Also ensures that the series of SPS/PPS/SEI NALU before a keyframe
can be considered as one contiguous header
In the same way we do it for the DELTA_UNIT flag
This allows downstream elements to know whether a given mpeg-ts
packet contains a corresponding HEADER elementary unit
Timestamps should start at the segment start, rather than 0, so
we need to not subtract the first timestamp. This makes the sink
correctly account for running time when switching PMTs where a
stream starts not quite at zero, causing timing offsets that can
become noticeable and causing dropped frames after a few times.
A new program object is created to replace an existing one
in the programs hash table, so its refcount needs to match.
With the default of 0 refcount on creation, the next PAT
change will cause that refcount to be both incremented and
decremented (assuming the new PAT references that stream too),
which will cause the program to be destroyed.
https://bugzilla.gnome.org/show_bug.cgi?id=748412
In the H263 spec, CPFMT is present only if the use of a custom
picture format is signalled in PLUSEPTYPE and UFEP is "001",
so we need to check params->format and only if the value is
6 (custom source format) the CPFMT should be read, otherwise
it's not present and wrong data will be parsed.
When reading the CPFMT, the width and height were not
calculated correctly (wrong bitmask).
https://bugzilla.gnome.org//show_bug.cgi?id=749253
Rather than one of the input pad video info's.
The test checking this was not constraining the output frame size
to ensure that the out of frame stream was not being displayed.
No need to call gst_remove_silence_reset() in gst_remove_silence_init() because
vad_new() already calls this function. Since there are no more uses of
_silence_reset(), we can remove it altogether.
Don't use the apis in codec-utils to extract the profile and level
syntax elements since it is wrong if there are emulation prevention
bytes existing in the byte-stream data.
https://bugzilla.gnome.org/show_bug.cgi?id=747613
It's a waste of resources to map it if it won't be converted
or used at all. Since we moved the frame mapping down, we need
to use the GST_VIDEO_INFO accessor macros now in the code above
that instead of the GST_VIDEO_FRAME accessor macros.
https://bugzilla.gnome.org/show_bug.cgi?id=746147
For each frame, compare the frame boundaries, check if the format contains an
alpha channel, check opacity, and skip the frame if it's going to be completely
overwritten by a higher zorder frame. The check is O(n^2), but that doesn't
matter here because the number of sinkpads is small.
More can be done to avoid needless drawing, but this covers the majority of
cases. See TODOs. Ideally, a reverse painter's algorithm should be used for
optimal drawing, but memcpy during compositing is small compared to the CPU used
for frame conversion on each pad.
https://bugzilla.gnome.org/show_bug.cgi?id=746147
Don't use the apis in codec-utils to extract the profile,tier and level
syntax elements since it is wrong if there are emulation prevention
bytes existing in the byte-stream data.
https://bugzilla.gnome.org/show_bug.cgi?id=747613
