Probe supported formats in order of desirability rather than in
what order they may happen to be in the formats bitmask. Fixes
accidentally exposure of 8-bit formats in caps before 16-bit formats
(in case where U16 was not supported S8 might be listed before S16).
https://bugzilla.gnome.org/show_bug.cgi?id=706884
This is required as during preroll we pass the first buffer twice, hence already
queued. It is also useful, to allow filters replaying a previous rendered buffers.
This will require 1 more buffer in sink if last-sample is enabled, since the last
sample will not be the same as the currently queued buffer.
https://bugzilla.gnome.org/show_bug.cgi?id=722303
For output device, we where queuing all the buffers, and then we would
dequeue one. This means we only have 1 buffer for the pipeline, no matter
the size of the queue. Instead, start dequeued when min_latency is reached.
Eventually, this the min_latency should also be affected by control
MIN_BUFFERS_FOR_OUTPUT (use by encoders).
Calculation of num_buffers (the max latency in buffers) was
up-side-down. If we can allcoate, then our maximum latency match
pool maximum number of buffers. Also renamed it to max latency. Finally
introduced a min_latency for clarity.
Fix the choice of min/max, don't override the min/max with own pool selected
size, correct other_pool is_active check, start from other_pool config when
configuring the other pool and finally validate the configuration.
The decodeing thread returning flushing isn't an error, we should simply
try starting the task again. If it's actually flushing, it will stop again by itself.
From time to time, when the image_pool list has more then 1 element
and I suppose at start, all but 1 pooled ximage are leaked. This is
due to broken algorithm in gst_ximagesink_src_ximage_get(). There was
also a risk of use after free for the case where the ximage size has
changed.
https://bugzilla.gnome.org/show_bug.cgi?id=728502
gstv4l2bufferpool.c:608:18: error: implicit conversion from enumeration type
'enum _GstV4l2BufferPoolAcquireFlags' to different enumeration type
'GstBufferPoolAcquireFlags' [-Werror,-Wenum-conversion]
params.flags = GST_V4L2_POOL_ACQUIRE_FLAG_RESURECT;
~ ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We need to handle the case where a flush occure while the streaming
thread is being brought up. In this case, the flushing state of the poll
object is cleared. To solve this, we simply set the capture poll to flushing
again, this way we know the thread will exit. The decoder streamlock
is used to synchronize with handle frame.
M2M devices were sharing the same properties as src and sink. Most of
these made no sense. This patch reduces the number of propeties and
makes io-mode clearer by having capture-io-mode and output-io-mode. This
also accidently fixed a bug in gstv4l2transform io-mode code, where the
capture io-mode could not be set.
https://bugzilla.gnome.org/show_bug.cgi?id=729591
If the driver need more buffers than requested by the config,
update the pool min/max values. The minimum value for the pool
could be provided either by the driver or by the pool. This is
best effort for drivers that don't support
CID V4L2_CID_MIN_BUFFERS_FOR_CAPTURE.
https://bugzilla.gnome.org/show_bug.cgi?id=730200
This allow calling start streaming later for capture device. Currently it breaks
in dmabuf-import because downstream is holding a buffer that will only be
released after stream-start.
https://bugzilla.gnome.org/show_bug.cgi?id=730207
When extrapolating the offset, we need to use the extrapolate
stride rather then the base stride. This should fix support for format
with more then two planes (I420, Y42B, etc).
When doing frame operation, we need to use the default VideoInfo
and let the frame API read the video meta in order to get the stride
and offset right. Currently we where using the specialized VideoInfo
which reflects what the HW is setup to.
Simplify framerate field if possible, so we don't end up with
e.g. framerate = (fraction) { 30/1 }. Maybe the helper function
should be moved to core, but we can do this later.
