It is compared to other extended RTP timestamps all over rtpjitterbuffer
and since 4df3da3bab the initial extended RTP timestamp is not equal
anymore to the plain RTP time.
Continue passing a non-extended RTP timestamp via the `sync` signal for
backwards compatibility. It will always be a timestamp inside the first
extended timestamp period anyway.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6536>
When the buffer DTS is estimated based on arrival time at the
jitterbuffer (rather than provided on the incoming buffer itself),
it shouldn't be used for skew adjustment. The typical case is
packets being deinterleaved from a tunnelled TCP/HTTP RTSP stream,
and the arrival times at the jitter buffer are not well enough
correlated to usefully do skew adjustments.
This restores the original intended behaviour for the 'estimated dts'
path, that was broken years ago during other jitterbuffer refactoring.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6509>
If we can calculate timestamps for buffers, then set the duration
on outgoing buffers based on the number of samples depayloaded.
This can fix the muxing to mp4, where otherwise the last packet
in a muxed file will have 0 duration in the mp4 file.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6447>
When we're doing a state change from PLAYING to NULL, first we invoke
gst_rtspsrc_loop_send_cmd_and_wait (..., CMD_CLOSE, ...) during
PAUSED_TO_READY which will schedule a TEARDOWN to happen async on the
task thread.
The task thread will call gst_rtspsrc_close(), which will send the
TEARDOWN and once it's complete, it will call gst_rtspsrc_cleanup()
without taking any locks, which frees src->streams.
At the same time however, the state change in the app thread will
progress further and in READY_TO_NULL it will call gst_rtspsrc_stop()
which calls gst_rtspsrc_close() a second time, which accesses
src->streams (without a lock again), which leads to simultaneous
access of src->streams, and a segfault.
So the state change and the cleanup are racing, but they almost always
complete sequentially. Either the cleanup sets src->streams to NULL or
_stop() completes first. Very rarely, _stop() can start while
src->streams is being freed in a for loop. That causes the segfault.
This is unlocked access is unfixable with more locking, it just leads
to deadlocks. This pattern has been observed in rtspsrc a lot: state
changes and cleanup in the element are unfixably racy, and that
foundational issue is being addressed separately via a rewrite.
The bandage fix here is to prevent gst_rtspsrc_stop() from accessing
src->streams after it has already been freed by setting src->state to
INVALID.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6302>
The transport stream only returned the CAPS for the first matching PT entry
from the `ptmap`. Other SSRC with the same PT where not included. For a stream
which bundled multiple audio streams for instance, only the first SSRC was
knowed to the SSRC demux and downstream elements.
This commit adds all the `ssrc-` attributes from the matching PT entries.
The RTP jitter buffer can now find the CNAME corresponding its SSRC even if it
was not the first to be registered for a particular PT.
The RTP PT demux removes `ssrc-*` attributes cooresponding to other SSRCs
before pushing SSRC specific CAPS to downstream elements.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6119>
And also re-timestamp them with the current buffer's PTS.
Not doing so keeps the timestamps of event packets as
GST_CLOCK_TIME_NONE or the timestamp of the previous buffer, both of
which are bogus.
Making sure that (especially) the first packet has a valid timestamp
allows putting e.g. the NTP timestamp RTP header extension on it.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/5173>
Parse the speed and scale in the server's response
*before* the range, so that the range start/stop
are swapped (or not swapped) correctly based
on the server's actual chosen values. Otherwise,
the old rate from the segment is used - what the
last seek asked for, but not necessarily what
the server chooses.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6248>
After a flushing seek, rtspsrc doesn't reset the last_ret value for
streams, so might immediately shut down again when it resumes pushing
buffers to pads due to a cached `GST_FLOW_FLUSHING` result
Prevent a stored flushing value from immediately stopping
playback again by resetting pad flows before (re)starting
playback.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6137>
Because this depayloader may build several output buffers within one
process run we push them all into a GstBufferList and push them out at
once to make sure that each buffer gets notified about each header
extension.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/5378>
Because this depayloader may build several output buffers within one
process run we push them all into a GstBufferList and push them out at
once to make sure that each buffer gets notified about each header
extension.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/5378>
Because this depayloader may build several output buffers within one
process run we push them all into a GstBufferList and push them out at
once to make sure that each buffer gets notified about each header
extension.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/5378>
Because this depayloader may build several output buffers within one
process run we push them all into a GstBufferList and push them out at
once to make sure that each buffer gets notified about each header
extension.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/5378>
Because this depayloader may build several output buffers within one process
run we push them all into a GstBufferList and push them out at once to
make sure that each buffer gets notified about each header extension.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/5378>
In rtpbin we already systematically check for all property names
except latency, correct that.
In webrtcbin we need to check before trying to use the do-retransmission
property.
This is useful for the case where an element like identity gets passed
to rtpbin's request-jitterbuffer property, when the application wants
to use webrtcbin in an SFU situation, with no reordering and no added
latency
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6112>
Today when using the `splitmuxsrc` on a collection of files named as:
```
item0.mkv
item1.mkv
item2.mkv
[...]
item10.mkv
item11.mkv
[...]
```
You will get a continuous stream made in the order of:
```
item0.mkv -> item1.mkv -> item10.mkv -> item11.mkv -> [...]
```
You can fix this by having smarter names of the items:
```
item000.mkv
item001.mkv
item002.mkv
[...]
item010.mkv
item011.mkv
[...]
```
Will get you:
```
item000.mkv -> item001.mkv -> item003.mkv -> item004.mkv -> [...]
```
But, we could also "fix" the former case by using natural ordering when
comparing the files in gstsplitutils.c.
Fixes#2523
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/4491>
