This flag is to indicate to child elements that they can add and
remove pads at any point in time without re-adding existing ones.
Elements should post before-hand a GST_MESSAGE_STREAM_COLLECTION
https://bugzilla.gnome.org/show_bug.cgi?id=772741
When we get GST_ITERATOR_RESYNC, we need to call gst_iterator_resync()
otherwise we will always get GST_ITERATOR_RESYNC (and that loop would
run forever).
gst/gstprintf unit test would fail on 32-bit x86 with:
gstprintf.c:83:printf_I32_I64:0: 'str' (64-bit x value = b5a6978f) is not equal to '"64-bit x value = f1e2d3c4b5a6978f"'
This reverts commit cfc565e2d8.
The commit was redundant since gst_gen_sources already contains
gstenum_h. We're still investigating why some people are still seeing
a racy build failure.
This forces gstenumtypes.h to be built whenever something uses gst_dep
as a subproject dependency. This is needed since gst/gst.h includes
gstenumtypes.h
Closes https://github.com/mesonbuild/meson/issues/714 which is not
actually a Meson bug.
This carries over code for a similar test from multiqueue to ensure full
control over the dataflow while testing. (The previous attempt was racy
since the fill level changed without any thread sync with the test code.)
https://bugzilla.gnome.org/show_bug.cgi?id=771210
Earlier we were only using __declspec(dllexport/import) when we were
built with MSVC because when built with MinGW and linking with MinGW we
don't need it (and we get linker errors because of it).
However, when we're built with MinGW and someone wants to link to us
with MSVC, we still need the prototypes to have __declspec(dllimport)
since MSVC cannot do auto-import like GCC can.
https://bugzilla.gnome.org/show_bug.cgi?id=771029
When using seek_simple() in combination with other kinds of seeks, this
becomes problematic. seek_simple() does not reset the stop position to
GST_CLOCK_TIME_NONE but keeps whatever a previous seek did. So for example
when doing a seek_simple() after a rate=-1 seek, we would usually get
assertions that start>stop (and stop being the old stop from the rate=1 seek).
https://bugzilla.gnome.org/show_bug.cgi?id=771104
Basically we already have each test with a 20sec timeout,
and testsuite can last more than the default 30secs from
meson. 3 minutes is another arbitrary timeout but should
be good enough.
The durations of the buffers are (usually) assuming that no frames are being
dropped and are just the durations coming from the stream. However if we do
trickmodes, frames are being dropped regularly especially if only key units
are supposed to be played.
Fixes completely bogus QoS proportion values in the above case.
low/high-watermark are of type double, and given in range 0.0-1.0. This
makes it possible to set low/high watermarks with greater resolution,
which is useful with large multiqueue max sizes and watermarks like 0.5%.
Also adding a test to check the fill and watermark level behavior.
https://bugzilla.gnome.org/show_bug.cgi?id=770628
To make the code clearer, and to facilitate future improvements, introduce
a distinction between the buffering level and the buffering percentage.
Buffering level: the queue's current fill level. The low/high watermarks
are in this range.
Buffering percentage: percentage relative to the low/high watermarks
(0% = low watermark, 100% = high watermark).
To that end, get_percentage() is renamed to get_buffering_level(). Also,
low/high_percent are renamed to low/high_watermark to avoid confusion.
mq->buffering_percent values are now normalized in the 0..100 range for
buffering messages inside update_buffering(), and not just before sending
the buffering message. Finally the buffering level range is parameterized
by adding a new constant called MAX_BUFFERING_LEVEL.
https://bugzilla.gnome.org/show_bug.cgi?id=770628
