In push mode we process as much as possible in the adapter. When we receive
a DISCONT buffer which we can't match to an actual sample (based on the existing
sample table) and there is still data remaining in the incoming adapter,there is
one of two cases happening:
1) We are doing reverse playback, in which case we should flush out all pending
data
2) We have leftover data from the previous incoming buffer... which we can't do
anything about.
For the second case, make sure we flush out the remaining data so that we can start
parsing again from scratch.
https://bugzilla.gnome.org/show_bug.cgi?id=781319
They should have ideally the same timescale of the video track, which we
can't guarantee here as in theory timecode configuration and video
framerate could be different. However we should set a correct timescale
based on the framerate given in the timecode configuration, and not just
use the framerate numerator.
Make sure offset and neededbytes are properly resetted when all
streams are EOS in push-mode.
Avoids cases when some data might still be pushed by upstream (because
it didn't yet see the resulting GST_FLOW_EOS yet) and qtdemux gets
completely lost.
https://bugzilla.gnome.org/show_bug.cgi?id=781266
buf is the current pad->last_buf value. If ever it gets copied/unreffed,
we need to make sure to write back the new pointer to the last_buf
variable.
Fixes using wrong pointer values in the case of decrasing DTS value
Before pushing a sample, check if there was a change in the current
stsd entry. This patch also assumes that the first stsd entry is
used as default for the first sample. It might cause an uneeded
caps renegotiation when this isn't the case.
stsd can have multiple format entries, parse them all.
This is required to play DVB DASH profile that uses multiple entries
to identify the different available bitrates/options on dash streams
The stream format-specific data is not stored into QtDemuxStreamStsdEntry
Instead of using the stsd as a base pointer, use the actual stsd
entry as the stsd can have multiple entries. This is rarely used
for file playback but is a possible profile with in DVB DASH specs.
This still doesn't support stsd with multiple entries but makes it
easier to do so.
last_buf is the one we're going to write next, not buf. As such we
should check timestamps against that one if there is one to select the
earliest pad.
Also remember the currently selected pad in the very beginning when
storing the first last_buf.
This both solves some edge cases where not the correct next pad was
selected corresponding to the target interleave.
This is an update of d78d589627
We still exit as early as possible in case of non-ok/non-unlinked combined
flow, but we first make sure that we update the internal position variables.
This ensures that if upstreams "ignores" the flow return (and carries on pushing),
we don't end up processing data with completely bogus variables/positions.
TFDTs with time 0 are being ignored since commit 1fc3d42f. They're
mistaken with the case of not having TFDT, but those two cases
must be distinguished in some way.
This patch passes an extra boolean flag when the TFDT is present.
This is now the condition being evaluated, instead of checking for
0 time.
https://bugzilla.gnome.org/show_bug.cgi?id=780410
If we have multiple tracks with timecodes, or it's not the first track
that has timecodes, or not the first buffer, we already started a chunk
for media data. We now need to "close" that chunk because we wrote data
for the timecode track and a new chunk has to be started for the
original track the next time it has data.
Similar to what was done in adaptivedemux, ignore seek
events we've already handled - such as when they are received
on every srcpad of files with lots of streams.
Otherwise mdatleft will have a value calculated from the initial
mdatsize minus the parts of the stream that we saw, which is not
including all the parts of the stream that might've been skipped.
Take into account the atoms at the end of the 'trak' atom when
recovering it. So that its size (already computed and added in the trak
size) isn't making offsets wrong.
https://bugzilla.gnome.org/show_bug.cgi?id=771478
We parse the next moof in advance of having pushed
all samples from the previous one in some cases, and
we'll still need the crypto info from the previous
fragment so keep around any unused crypto info entries
when adding new ones
qtdemux.c: In function ‘qtdemux_parse_samples’:
qtdemux.c:8450:39: error: ‘*’ in boolean context, suggest ‘&&’ instead [-Werror=int-in-bool-context]
if (stream->samples_per_frame * stream->bytes_per_frame) {
~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~
This reverts commit 107902ec51.
This commit intended to ensure that keyframe seeks land at the
start timestamp of a keyframe, rather than in the middle of one,
but they cause trouble on files with sparse streams, or with
JPEG 'cover art' tracks that have only one or a few JPEG samples
with very long durations.
That's still desirable for doing seamless cutting of videos,
but needs a rethink for implementation.
https://bugzilla.gnome.org/show_bug.cgi?id=778690
The n_frames field (frames per second) should follow the nominal frame
rate for drop-frame timecodes.
Also, the trak's timescale (and duration, accordingly) should follow the
STSD entry's timescale and frame duration (fps_n and fps_d accordingly),
not the other way around.
https://bugzilla.gnome.org/show_bug.cgi?id=777832
qtdemux_handle_xmp_taglist() requires a writable taglist,
but qtdemux->tag_list can become non-writable, specifically
after sending global tags (qtdemux.c:958), which adds a
second reference. Ensure the list is made writable before
calling (make_writable will copy the list if necessary).
https://bugzilla.gnome.org/show_bug.cgi?id=766177
These are usually much bigger than icon size and required by
iTunes to be certain fairly large sizes. In qtmux it is also
the IMAGE tags which we write out as 'covr' atoms.
When reset, don't restart request pad numberings, as
request pads can survive across state changes. Only
restart at 0 if all request pads are handed back first.
https://bugzilla.gnome.org/show_bug.cgi?id=777174
'stream-format' and 'alignment' are defined in pad template caps so
there is no need to check them again here. Also remove bitrate parsing from
caps as bitrate in caps doesn't make sense but from tags, which is
actually the case.
https://bugzilla.gnome.org/show_bug.cgi?id=777181
Needed for QuickTime 7 to properly play files.
Also write the clap atom for MOV files always, not only when ProRes is
used as a video codec. It's mandatory for MOV.
https://bugzilla.gnome.org/show_bug.cgi?id=777100
The seqh buffer allocated in qtdemux_parse_svq3_stsd_data() needs to
be freed by the caller after use.
https://bugzilla.gnome.org/show_bug.cgi?id=777157
Signed-off-by: Andre McCurdy <armccurdy@gmail.com>
If a fragmented stream doesn't have a tfdt, don't
reset the output timestamps at each fragment boundary
by erroneously using the default value of 0. Introduced
by commit 69fc48
https://bugzilla.gnome.org/show_bug.cgi?id=754230
When performing a key-unit seek, always snap to the start ts
of the keyframe buffer we landed on so that the keyframe is
entirely within the resulting outgoing segment. That seems
the most sensible result, since the user requested snapping
to the keyframe position.
Segments times and seek requests are stored and handled
in raw 'PTS' time, without the cslg_shift - which only applies
to outgoing samples. Omit the cslg_shift portion when
extracting PTS to compare for internal seek snaps.
If the cslg_shift is included, then keyframe+snap-before seeks
generate a segment start/stop time that already includes the
cslg_shift, and it's then added a 2nd time, causing the
first buffer(s) to have timestamps that are out of segment.
Remove an old check from atom_stsc_add_new_entry() that
extends the last entry in the STSC if the samples per chunk
matches, as the new interleave merging logic requires that
the final entry by updateable. There's already code
below which simply merges the final entry into the previous
one when needed, so rely on that instead.
Fixes asserts like:
ERROR:atoms.c:2940:atom_stsc_update_entry: assertion failed:
(atom_array_index (&stsc->entries, len - 1).first_chunk == first_chunk)
We can't simply assume that the length of the tag value as given
inside the stream is correct but should also check against the amount of
data we have actually available.
https://bugzilla.gnome.org/show_bug.cgi?id=775451
qtdemux.c: In function ‘qtdemux_parse_trak’:
qtdemux.c:10184:38: error: format ‘%lu’ expects argument of type ‘long unsigned int’, but argument 9 has type ‘gint {aka const int}’ [-Werror=format=]
GST_DEBUG_OBJECT (qtdemux, "Found jpeg: len %u, need %lu", len,
^
39f7e52266 was setting the buffer duration
to 0 if is not valid, under the assumption that this is "the last"
buffer and no others are coming next. This is wrong, last_buf is the
previous buffer and not the very last one.
4e3c13c87c was setting DTS to 0 if there
was none. This will set DTS to 0 for all e.g. audio streams, completely
messing up calculations if streams don't start at 0.
https://bugzilla.gnome.org/show_bug.cgi?id=774840
| ../../../git/gst/isomp4/qtdemux.c: In function 'qtdemux_parse_tree':
| ../../../git/gst/isomp4/qtdemux.c:10224:24: error: 'size' may be used uninitialized in this function [-Werror=maybe-uninitialized]
| offset += size;
| ^~
| ../../../git/gst/isomp4/qtdemux.c:10197:25: note: 'size' was declared here
| guint32 size, tag;
| ^~~~
https://bugzilla.gnome.org/show_bug.cgi?id=774747
Always write an edit list for the whole track. In general this is not
necessary except for the case of having a gap or DTS adjustment but
it allows to give the whole track's duration in the usually more
accurate media timescale.
https://bugzilla.gnome.org/show_bug.cgi?id=774403
