This might create deadlocks and we need to avoid holding element
specific lock while posting messages
For example a deadlock will happen if while posting the message,
someone connected on the bus (sync) tries to DOT the pipeline.
https://bugzilla.gnome.org/show_bug.cgi?id=737102
It might cause deadlocks to post messages while holding the queue2
lock. To avoid this a new boolean flag is set whenever a new
buffering percent is found. The message is posted after the lock
is released.
To make sure the buffering messages are posted in the right order, messages
are posted holding another lock. This prevents 2 threads trying to post
messages at the same time.
https://bugzilla.gnome.org/show_bug.cgi?id=736969
It might cause deadlocks to post messages while holding the multiqueue
lock. To avoid this a new boolean flag is set whenever a new buffering percent
is found. The message is posted after the lock can be released.
To make sure the buffering messages are posted in the right order, messages
are posted holding another lock. This prevents 2 threads trying to post
messages at the same time.
https://bugzilla.gnome.org/show_bug.cgi?id=736295
Don't re-start the queue push task on the source pad when a
flush-stop event comes in and we're in the process of shutting
down, otherwise that task will never be stopped again.
When the element is set to READY state, the pads get de-activated.
The source pad gets deactivated before the queue's own activate_mode
function on the source pads gets called (which will stop the thread),
so checking whether the pad is active before re-starting the task on
receiving flush-stop should be fine. The problem would happen when the
flush-stop handler was called just after the queue's activate mode
function had stopped the task.
Spotted and debugged by Linus Svensson <linux.svensson@axis.com>
https://bugzilla.gnome.org/show_bug.cgi?id=734688
Otherwise it would only be proxied for the active pad which can lead
upstream to use an incompatible caps for the downstream element.
Even if a reconfigure event is sent upstream when the pad is activated, this
will save the caps reconfiguration if it is already using an acceptable caps.
Imagine the following 'pipeline'
--------------
p1/| 'fullqueue' |--- 'laggy' downstream
--------- / | |
-| demuxer | | multiqueue |
--------- \ | |
p2\| 'emptyqueue' |--- 'fast' downstream
--------------
In the case downstream of one single queue (fullqueue) has (a lot of) latency
(for example for reverse playback with video), we can end up having the other
SingleQueue (emptyqueue) emptied, before that fullqueue gets
unblocked. In the meantime, the demuxer tries to push on fullqueue, and
is blocking there.
In that case the current code will post a BUFFERING message on the bus when
emptyqueue gets emptied, that leads to the application setting the pipeline state to
PAUSED. So now we end up in a situation where 'laggy downstream' is
prerolled and will not unblock anymore because the pipeline is set to
PAUSED, the fullequeue does not have a chance to be emptied and
the emptyqueue can not get filled anymore so no more BUFERRING message
will be posted and the pipeline is stucked in PAUSED for the eternity.
Making sure that we do not try to "buffer" if one of the single queue
does not need buffering, prevents this situtation from happening though it lets the
oportunity for buffering in all other cases.
That implements a new logic where we need all singlequeue to need
buffering for the multiqueue to actually state buffering is needed,
taking the maximum buffering of the single queue as the reference point.
https://bugzilla.gnome.org/show_bug.cgi?id=734412
After EOS there will be no further buffer which could propagate the
error upstream, so nothing is going to post an error message and
the pipeline just idles around.
When eos events are forwarded simultaneouly from two sinkpads on
funnel, it doesnot forward the eos to sourcepad. The reason is
sticky events are stored after the event callbacks are returned.
Therefore while one is about to store the sticky events on the its
sinkpad, other sinkpad starts checking for the eos events on all other
sinkpads and assumes eos is not present yet.
https://bugzilla.gnome.org/show_bug.cgi?id=732851
Avoid relocations and refactor so that we don't calculate
the fixed and known at compile time maximum string size
every time. Also skip the mini object flags which we are
not going to print anyway.
The initial buffers (that were used for timestamping) might have PTS
and DTS set. In order to forward those properly, get the initial
PTS/DTS from the adapter and set them on the reconstructed output
buffer.
https://bugzilla.gnome.org/show_bug.cgi?id=733291
We always work in passthrough mode so there's no point in doing
something more clever in basetransform. Also the basetransform
code leads to problems with incomplete caps and downstream
elements that use GST_PAD_FLAG_ACCEPT_INTERSECT.
https://bugzilla.gnome.org/show_bug.cgi?id=732559
When no data is coming from sinkpads and eos events
arrived at one of the sinkpad, funnel forwards the EOS
event to downstream. It forwards the EOS because lastsink pad
is NULL. Also the unit testcase of the funnel is not checking
the correct behavior as it should. The unit test case should
fail if one of the sink pad has already EOS present on it and
we are trying to push one more EOS.
https://bugzilla.gnome.org/show_bug.cgi?id=731716
The start and stop should represent the currently downloading region.
The estimated-total should represent the remaining time to download
the currently downloading region. This makes it a lot more useful
for applications because they can then use those values to update
the fill region and use the estimated time to delay playback.
Update the docs with this clarification.
