mirror of
https://github.com/ferrous-systems/embedded-trainings-2020.git
synced 2024-05-28 21:28:20 +00:00
172dbc17cd
Use the target actually mentioned in the .cargo/config file. Updated the output in the troubleshooting page and also updated the target for the board/dongle.
206 lines
6.5 KiB
Markdown
206 lines
6.5 KiB
Markdown
# Installation Instructions
|
|
|
|
## VS Code
|
|
|
|
**Windows**: Go to [https://code.visualstudio.com](https://code.visualstudio.com) and run the installer.
|
|
|
|
**Linux**: Check your Linux distribution package manager (example below). If it's not there, follow the instructions on [https://code.visualstudio.com/docs/setup/linux](https://code.visualstudio.com/docs/setup/linux).
|
|
|
|
``` console
|
|
$ # Arch Linux
|
|
$ sudo pacman -S code
|
|
```
|
|
|
|
**macOS**: Go to [https://code.visualstudio.com](https://code.visualstudio.com) and click on "Download for Mac"
|
|
|
|
## OS specific dependencies
|
|
|
|
### Linux only: USB
|
|
|
|
Some of our tools depend on `pkg-config` and `libudev.pc`. Ensure you have the proper packages installed; on Debian based distributions you can use:
|
|
|
|
``` console
|
|
$ sudo apt-get install libudev-dev libusb-1.0-0-dev
|
|
```
|
|
|
|
To access the USB devices as a non-root user, follow these steps:
|
|
|
|
1. (Optional) Connect the dongle and check its permissions with these commands:
|
|
|
|
``` console
|
|
$ lsusb -d 1915:521f
|
|
Bus 001 Device 016: ID 1915:521f Nordic Semiconductor ASA USB Billboard
|
|
$ # ^ ^^
|
|
|
|
$ # take note of the bus and device numbers that appear for you when run the next command
|
|
$ ls -l /dev/bus/usb/001/016
|
|
crw-rw-r-- 1 root root 189, 15 May 20 12:00 /dev/bus/usb/001/016
|
|
```
|
|
|
|
The `root root` part in `crw-rw-r-- 1 root root` indicates the device can only be accessed by the `root` user.
|
|
|
|
2. Create the following file with the displayed contents. You'll need root permissions to create the file.
|
|
|
|
``` console
|
|
$ cat /etc/udev/rules.d/50-oxidize-global.rules
|
|
# udev rules to allow access to USB devices as a non-root user
|
|
|
|
# nRF52840 Dongle in bootloader mode
|
|
ATTRS{idVendor}=="1915", ATTRS{idProduct}=="521f", TAG+="uaccess"
|
|
|
|
# nRF52840 Dongle applications
|
|
ATTRS{idVendor}=="2020", TAG+="uaccess"
|
|
|
|
# nRF52840 Development Kit
|
|
ATTRS{idVendor}=="1366", ATTRS{idProduct}=="1015", TAG+="uaccess"
|
|
```
|
|
|
|
3. Run the following command to make the new udev rules effective
|
|
|
|
``` console
|
|
$ sudo udevadm control --reload-rules
|
|
```
|
|
|
|
4. (Optional) Disconnect and reconnect the dongle. Then check its permissions again.
|
|
|
|
``` console
|
|
$ lsusb
|
|
Bus 001 Device 017: ID 1915:521f Nordic Semiconductor ASA 4-Port USB 2.0 Hub
|
|
|
|
$ ls -l /dev/bus/usb/001/017
|
|
crw-rw-r--+ 1 root root 189, 16 May 20 12:11 /dev/bus/usb/001/017
|
|
```
|
|
|
|
The `+` part in `crw-rw-r--+` indicates the device can be accessed without `root` permissions.
|
|
|
|
### Windows only: Zadig JLink driver
|
|
|
|
On Windows you'll need to associate the nRF52840 Development Kit's USB device to the WinUSB driver.
|
|
|
|
To do that connect the nRF52840 DK to your PC using micro-USB port J2 (as done before) then download and run the [Zadig] tool.
|
|
|
|
[Zadig]: https://zadig.akeo.ie/
|
|
|
|
In Zadig's graphical user interface,
|
|
|
|
1. Select the 'List all devices' option from the Options menu at the top.
|
|
|
|
2. From the device (top) drop down menu select "BULK interface (Interface 2)"
|
|
|
|
3. Once that device is selected, `1366 1015` should be displayed in the USB ID field. That's the Vendor ID - Product ID pair.
|
|
|
|
4. Select 'WinUSB' as the target driver (right side)
|
|
|
|
5. Click "Install WinUSB driver". The process may take a few minutes to complete.
|
|
|
|
> You do not need to do anything for the **nRF52840 Dongle** device.
|
|
|
|
## Rust and tooling
|
|
|
|
### Base Rust installation
|
|
|
|
Go to [https://rustup.rs](https://rustup.rs/) and follow the instructions.
|
|
|
|
**Windows**: *Do* install the optional components of the [C++ build tools package](https://visualstudio.microsoft.com/visual-cpp-build-tools/). The installation size may take up to 2 GB of disk space.
|
|
|
|
### Rust Analyzer
|
|
|
|
**All**: Open VS Code and look for [Rust Analyzer](https://marketplace.visualstudio.com/items?itemName=matklad.rust-analyzer) in the marketplace (bottom icon in the left panel). Then install it.
|
|
|
|
**Windows**: It's OK to ignore the message about `git` not being installed, if you get one!
|
|
|
|
### Rust Cross compilation support
|
|
|
|
**All**: Run this command in a terminal:
|
|
|
|
``` console
|
|
$ rustup +stable target add thumbv7em-none-eabihf
|
|
```
|
|
|
|
### ELF analysis tools
|
|
|
|
**All**: Run these commands in a terminal:
|
|
|
|
``` console
|
|
$ rustup +stable component add llvm-tools-preview
|
|
|
|
$ cargo install cargo-binutils
|
|
```
|
|
|
|
### Cargo subcommands
|
|
|
|
Install version v0.8.0 of the [`cargo-flash`](https://crates.io/crates/cargo-flash) and [`cargo-embed`](https://crates.io/crates/cargo-embed) subcommands, as well as the [`cargo-binutils`](https://crates.io/crates/cargo-binutils) set of subcommands and the [`cargo-bloat`](https://crates.io/crates/cargo-bloat) subcommand using the following Cargo commands:
|
|
|
|
``` console
|
|
$ cargo install cargo-flash --version 0.8.0 -f
|
|
(..)
|
|
Installed package `cargo-flash v0.8.0` (..)
|
|
|
|
$ cargo install cargo-embed --version 0.8.0 -f
|
|
(..)
|
|
Installed package `cargo-embed v0.8.0` (..)
|
|
|
|
$ cargo install cargo-binutils
|
|
(..)
|
|
Installed package `cargo-binutils v0.3.0` (..)
|
|
|
|
$ cargo install cargo-bloat
|
|
(..)
|
|
Installed package `cargo-bloat v0.9.3` (..)
|
|
|
|
$ cargo install probe-run
|
|
(..)
|
|
Installed package `probe-run v0.1.3` (..)
|
|
```
|
|
|
|
## Python
|
|
|
|
**Windows**: Go to [https://www.python.org/downloads/](https://www.python.org/downloads/) and run the Python *3* installer
|
|
|
|
- in the installer check the "add Python 3.x to PATH" box
|
|
- also run the "Disable path length limit" action at the end, if you are on Windows 10 and the option is displayed to you
|
|
|
|
**Linux**: Install `pip` using the package manager; this will also install Python.
|
|
|
|
``` console
|
|
$ # Arch Linux
|
|
$ sudo pacman -S python-pip
|
|
```
|
|
|
|
**macOS**:
|
|
Ensure that you have python 3 and pip installed. Refer to the following link for [Instructions on how to install python 3 and pip](https://docs.python-guide.org/starting/install3/osx/)
|
|
|
|
```console
|
|
$ python --version
|
|
Python 3.7.7
|
|
$ pip --version
|
|
pip 20.0.2 from /usr/local/lib/python3.7/site-packages/pip (python 3.7)
|
|
```
|
|
|
|
## nrf tools
|
|
|
|
### nrfutil
|
|
|
|
**All**: Open a terminal and install [nrfutil](https://github.com/NordicSemiconductor/pc-nrfutil) as follows. *If you are familiar with python, it is advised to do this in a [virtual environment](https://docs.python.org/3/library/venv.html).*
|
|
|
|
``` console
|
|
$ pip install nrfutil
|
|
(..)
|
|
|
|
$ nrfutil version
|
|
nrfutil version 6.1.0
|
|
```
|
|
|
|
### `nrf-recover`
|
|
|
|
Some nRF52840 devices, specially older revisions, may have parts of their Flash memory locked. To unlock the memory use the [`nrf-recover`](https://crates.io/crates/nrf-recover) tool.
|
|
|
|
This is only relevant to the nRF52840 Development Kit. First connect the nRF52840 DK to your PC using micro-USB J2 (as done before) then run the following commands:
|
|
|
|
``` console
|
|
$ cargo install nrf-recover
|
|
|
|
$ nrf-recover -y
|
|
Starting mass erase...
|
|
Mass erase completed, chip unlocked
|
|
``` |