alignment works like in mpegtsmux, joining several MpegTS packets into
one buffer. Default value of 0 joins as many as possible for each
incoming buffer, to optimise CPU usage.
If we have no DTS but a PTS then this means both are the same, and we
should update the last_ts with the PTS. Only if both are unknown then we
don't know the current position and should not update it at all.
Previously we would always update the last_ts to GST_CLOCK_TIME_NONE if
the DTS is unknown, which caused the position to jump around and to
cause spurious gap events to be sent.
Instead of doing it on each packet and doing it based on the distance to
the previous SCR instead of based on the DTS.
Previously we would send gap events for audio all the time if the SCR
distance was 400ms because the threshold for audio is 300ms and by only
ever updating the position when the SCR updates we would always be 100ms
above the threshold and send needless gap events.
This fixes audio glitches on various files caused by gap events.
Some raw h264 encoded files trigger the assignment of wrong PTS to buffers
when some SEI data is provided. This change prevents it to happen.
Also ensure this behavior is being tested.
We might have some old timecodes that are in the future now and have to
drop those to make sure that our queue is correctly ordered and we don't
have multiple timecodes for the same running time.
Directly read them out of the decoder as soon as we passed audio and
then store them in a queue that we handle internally together with their
timestamps. This cleans up memory management and gives us proper control
over the queue instead of guessing how the queue inside the LTC decoder
actually works and when it overflows.
And also introduce 6 instead of 2 frames of latency compared to the LTC
audio input as that seems to be an upper bound for how much the LTC
library is lagging behind.
As the H265/H264 bitstream can support multiple slices,
mastering_display_info_state and content_light_level_state
should be changed only on first slice segment.
Fix#1152
... by seeking to target offset determined by new seek segment,
rather than that of the previous segment. The latter would typically
seek back to start for a non-accurate seek, and lead to a lot
of skipping in case of an accurate seek.
If one of the inputs is live, add a latency of 2 frames to the video
stream and wait on the clock for that much time to pass to allow for the
LTC audio to be ahead.
In case of live LTC, don't do any waiting but only ensure that we don't
overflow the LTC queue.
Also in non-live LTC audio mode, flush too old items from the LTC queue
if the video is actually ahead instead of potentially waiting forever.
This could've happened if there was a bigger gap in the video stream.
According to H264 ITU standards from 06/19, GST_H264_PROFILE_HIGH_422
(profile_idc = 122) with constraint_set1_flag = 0 and
constraint_set3_flag = 0 can be mapped to high-4:2:2 or high-4:4:4.
GST_H264_PROFILE_HIGH_422 with constraint_set1_flag = 0 and
constraint_set3_flag = 1 can be mapped to high-4:2:2, high-4:4:4,
high-4:2:2-intra or high-4:4:4-intra.
The previous implementation had a very high reproducibility race where
if after a track switch, the ex-active track pad completed a buffer
chain (now returning not-linked) the flow combiner had all their pads in
non-linked state, propagating it as an error and stopping the pipeline.
By resetting the flow combiner in response to RECONFIGURE events that
race is made impossible.
Incrementing it afterwards will always have to phase_index >= 1 and we
will never be at the beginning (0) of the phase again, and thus never
reset timestamp tracking accordingly.
This was broken in bea13ef43b in 2010, and
causes interlace to run into integer overflows after 2^31 frames or
about 5 hours at 29.97fps. Due to usage of wrong types for the integers
this then causes negative numbers to be used in calculations and all
calculations spectacularly fail, leading to all following buffers to
have the timestamp of the first buffer minus one nanosecond.
Allowing the UDP elements to bind on an interface is needed in more
complex networks where there are mutiple networks interfaces without
default gateway
From the documentation of gst_base_parse_set_infer_ts, it should be
disabled for non-audio data. Currently just disabling for all video
parsers that have reordered data: h264, h265, mpeg, mpeg4, vc1. Was
already disabled in h263.
Currently tsdemux timestamps only the PTS, and only issues the DTS if
it's different. In that case, parsers tend to estimate the next DTS
based on the previous DTS and the duration, which can accumulate
rounding errors.
