For calculating the durations of each sample, we are supposed to add each
duration modulo 1<<32 so make the elapsed time counter a uint32.
Fixes#610280
Make the handing of the mime type within the "boundary" a bit less naive.
The standard for MIME allows parameters to follow the "type" / "subtype"
clause separated from the mime type by ';'.
Modifies the multipartdemuxer's header parsing so it doesnt assume
the whole line after "content-type:" is the mime type and thus makes it a bit
more resilient to finding absurd mime types in the case where parameters are
added.
Fixes#604711
ALAC codec-data apparently comes in (at least) two flavours (mov, mp4),
so use atom based parsing to retrieve required data, rather than
aiming for a specific offset.
See also #580731.
Remove some code where we pass ntpnstime around, we can do most things with the
running_time just fine.
Rename a variable in the ArrivalStats struct so that it's clear that this is the
current system time.
Don't calculate the NTP time based on the running_time of the pipeline but from
the systemclock. This allows us to generate more accurate NTP timestamps in case
the systemclock is synchronized with NTP or similar.
Used the _add_associationv variant of GstIndex since we know how many
associations we're adding. Trims up to 50% from index generation time.
Note : It would be great if the index could be generated on the fly or
on request as opposed to being fully created at startup.
If we detect backward timestamps on the server, don't try to resync when we
don't have an input timestamp (such as when using RTSP over TCP) instead, do
nothing but assume the timestamp was ok, it will correct itself when time goes
forwards.
There is no need to set the latency in the jittebuffer in _init, we will set
that later when going to PAUSED.
Set the jitterbuffer active and not buffering when starting.
When deactivating jitterbuffers when the buffering starts, keep the current
percent of the jitterbuffer and also set the jitterbuffer in the buffering state
so that we know when it's filled again.
Add property to get the buffering percentage of the jitterbuffer.
When we are in buffer mode, adjust the buffering low/high thresholds based on
the total configured latency. If we don't and there is a huge queue or element
with a big latency downstream we might drain the complete queue immediately and
start buffering again.
Return the next timestamp in the jitterbuffer.
Use the min-timestamp of the jitterbuffers to calculate an offset so that the
next timestamp is pushed with a timestamp equal to running_time.
Start producing timestamps from 0 in the buffering case too.
Keep track of the time we spend pausing the jitterbuffers when they were
buffering and distribute this elapsed time to the jitterbuffers.
Also keep the latency in nanosecond precision.
Pass the current running time to the jitterbuffer when pausing or resuming so
that it calculate the right offsets.
Small cleanups and comments.
Set the default rtspsrc latency to 2 seconds.
Add signal to pause the jitterbuffer. This will be emitted from gstrtpbin when
one of the jitterbuffers is buffering.
Make rtpbin collect the buffering messages and post a new buffering message with
the min value.
Remove the stats callback from jitterbuffer but pass a percent integer to
functions that affect the buffering state of the jitterbuffer. This allows us
then to post buffering messages from outside of the jitterbuffer lock.
Add callback for buffering stats.
Configure the latency in the jitterbuffer instead of passing it with _insert.
Calculate buffering levels when pushing and popping
Post buffering messages.
The audio packets in AVI are generally muxed ~0.5s before the
corresponding video packet. This changes causes downstream to only
receive packets with roughly corresponding timestamps.
Make sure we reset the demuxer correctly wrt parsing the index.
Don't leak pending seek events.
Rename some methods to reflect what they do and to avoid confusion with similar
method names.
Try to make the seeking threadsafe by protecting the setup code with a lock.
Make sure we post errors when a seek fails.
When we have not parsed any indexes yet, we don't know the length of the streams
and we must take the length given in the avih as a fallback.
Avoid some typechecking.
