Set as much information as possible on the slot (including the associated
track) *before* the associated source pad is added to the element.
We need this so that incoming event/queries can be replied to if they are
received when adding the pad
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6690>
Otherwise, if we run in to the copy case, this can cause these
groups to stay around with queued flag set, but never actually
queued, until gst_v4l2_allocator_flush() is called, which then
erroneously frees the associated memories, causing the release
function to decrement the allocator refcount where it was never
incremented, resulting in early allocator disposal, and either
deadlock or use after free.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6552>
Some decoder drivers need to wait enough capture buffers before
starting to decode. But the dequeued buffer flag LAST but empty
has no chance to queue back to driver, which makes decode hang
after seek. So need to queue back such kind of buffer to driver.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6579>
Output buffers don't have to be writable. Accepting read-only buffers
from the V4L2 buffer pool allows upstream elements to write directly
into the V4L2 buffers without triggering a CPU copy into a new buffer
from the same V4L2 buffer pool every time.
Tested with the vivid output device:
GST_DEBUG=GST_PERFORMANCE:7 gst-launch-1.0 videotestsrc ! v4l2sink device=/dev/video5
With this change, gst_v4l2_buffer_pool_dqbuf() must be allowed to not
resize read-only memories of output buffers.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6572>
* RED_OR_ALPHA8 will map value to alpha for OpenGL, use R8 to avoid
2nd shader
* Determine texel size for proper texture memory preparation
* QByteArray::fromRawData() does shallow copy and thus leads to use of
corrupted memory
* Make sure RGBA dummy texture is fully opaque
* QRhiTexture::create() must be called to allocate texture resources
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6578>
During RTP-Info synchronization, clock_base was temporarily switched
from the actual clock-base to the base RTP time and then back some lines
later.
Instead directly work with the base RTP time. The comment about using a
signed variable for convenience doesn't make any sense because all
calculations done with the value are unsigned.
Similarly, rtp_clock_base was overridden with the rtp_delta when
calculating it, which was fine because it is not used anymore
afterwards. Instead, introduce a new variable `rtp_delta` to make this
calculation clearer.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6536>
It's not in the same period as the current RTP base time but always in
the very first period. This avoids using it again at a much later time.
The code in question is only triggered with rtcp-sync=rtp-info.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6536>
It is compared to other extended RTP timestamps all over rtpjitterbuffer
and since 4df3da3bab the initial extended RTP timestamp is not equal
anymore to the plain RTP time.
Continue passing a non-extended RTP timestamp via the `sync` signal for
backwards compatibility. It will always be a timestamp inside the first
extended timestamp period anyway.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6536>
When the buffer DTS is estimated based on arrival time at the
jitterbuffer (rather than provided on the incoming buffer itself),
it shouldn't be used for skew adjustment. The typical case is
packets being deinterleaved from a tunnelled TCP/HTTP RTSP stream,
and the arrival times at the jitter buffer are not well enough
correlated to usefully do skew adjustments.
This restores the original intended behaviour for the 'estimated dts'
path, that was broken years ago during other jitterbuffer refactoring.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6509>
If we can calculate timestamps for buffers, then set the duration
on outgoing buffers based on the number of samples depayloaded.
This can fix the muxing to mp4, where otherwise the last packet
in a muxed file will have 0 duration in the mp4 file.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6447>
Some driver doesn't implement enum_framesize. The maximum supported
size can be got by trying format with a very large size. Also need
to set max_width/max_height for this case, otherwise default encoded
buffer size 256kB is too small.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/6416>
