Updated Decklink SDK to version 11.2 in order to support newer cards like the Decklink 8K Pro.
This required to replace the duplex property by a profile property.
Profile values can be the following:
- bmdProfileOneSubDeviceFullDuplex
- bmdProfileOneSubDeviceHalfDuplex
- bmdProfileTwoSubDevicesFullDuplex
- bmdProfileTwoSubDevicesHalfDuplex
- bmdProfileFourSubDevicesHalfDuplex
Fixes#987
Part-of: <https://gitlab.freedesktop.org/gstreamer/gst-plugins-bad/-/merge_requests/1665>
Instead of using the information we stored ourselves for the video frame
itself. Which was also the wrong one: it was the mode from the property,
not the autodetected one.
This fixes vanc extraction with mode=auto
Previously we would've reported that there is signal unless we know for
sure that we don't have signal. For example signal would've been
reported before the device is even opened.
Now keep track whether the signal state is unknown or not and report no
signal if we don't know yet. As before, only send an INFO message about
signal recovery if we actually had a signal loss before.
If the "output-cc" property is set to TRUE and there is CC present
in the VBI Ancillary Data, they will be extracted and set on the
outgoing buffer as GstVideoCaptionMeta.
Only CDP packets are supported.
https://bugzilla.gnome.org/show_bug.cgi?id=773863
When we receive a video or audio buffer, we calculate the next stream
time based on the current stream time + buffer duration. If the next
buffer's stream time is after that, we issue a warning.
This happens because the stream time incoming from Decklink should be
really constant and without gaps. If there is a gap, it means that
something went wrong, e.g. the internal buffer pool is empty (too many
buffers queued up downstream).
https://bugzilla.gnome.org/show_bug.cgi?id=781776
When we receive a video or audio buffer, we calculate the next stream
time based on the current stream time + buffer duration. If the next
buffer's stream time is after that, we issue a warning.
This happens because the stream time incoming from Decklink should be
really constant and without gaps. If there is a gap, it means that
something went wrong, e.g. the internal buffer pool is empty (too many
buffers queued up downstream).
https://bugzilla.gnome.org/show_bug.cgi?id=781776
On some hardware the first few frames are bogus and not very useful.
Their timestamps are off, they have no timecodes, or there are spurious
black frames / no-signal frames. After a few frames this stabilizes
though.
https://bugzilla.gnome.org/show_bug.cgi?id=774850
Based on this we calculate the actual capture time, which should get us
rid of any capturing jitter by averaging it out.
Also add a output-stream-time property which forces the elements to
output the stream time directly instead of doing any conversion to the
pipeline clock. Use with care.
https://bugzilla.gnome.org/show_bug.cgi?id=774850
The hardware timestamps have no relation to when frames were produced,
only when frames arrived somewhere in the hardware. Especially there is
no guarantee that audio and video will have the same hardware timestamps
although they belong together, and even more important: the rate with
which the hardware timestamps increase is completely unrelated to the
rate with which the frames are captured!
As such we can as well use the pipeline clock directly and stop doing
complicated calculations. Also as a side effect this allows now running
without any pipeline clock, by directly making use of the stream times
as reported by the driver.
https://bugzilla.gnome.org/show_bug.cgi?id=774850
When a frame is found to not have an associated input source (cable
unplugged, wrong mode selected), an element warning will be issued. When
the next frame in the stream is found to have an input source selected
(e.g. cable replugged), an element info will be issued.
https://bugzilla.gnome.org/show_bug.cgi?id=774629
