Before this patch, if mode=auto and video-format!=auto, video-format would
always be ignored, and get set to 8bit-yuv, or if detected to be RGB444, then
it would be set to 8bit-argb. This change respects video-format if it is set
to 10bit-yuv (v210) or 8bit-bgra, even when mode=auto.
Closes#772
There's a race condition when is-live is set to true and the shmsrc
element releases the pipe in the transition from PLAYING to PAUSED.
To avoid it this change ensures that _create method takes the pipe
and increases the use_count in one operation protected by object lock.
Also perform apropriate protections when releasing the pipe.
https://bugzilla.gnome.org/show_bug.cgi?id=797203
../sys/decklink/gstdecklinkvideosink.cpp:1006:11: error: ‘GstDecklinkVideoSink {aka struct _GstDecklinkVideoSink}’ has no member named ‘scheduled_stop_time’
self->scheduled_stop_time = start_time;
^
Decklink sometimes does not notify us through the callback that it has
stopped scheduled playback either because it was uncleanly shutdown
without an explicit stop or for unknown other reasons.
Wait on the cond for a short amount of time before checking if scheduled
playback has stopped without notification.
https://bugzilla.gnome.org/show_bug.cgi?id=797130
This is part of a much larger goal to always keep the frames we schedule to
decklink be always increasing. This also allows us to avoid using both the
sync and async frame display functions which aren't recomended to be used
together.
If the output timestatmsp is not always increasing decklink seems to hold
onto the latest frame and may cause a flash in the output if the played
sequence has a framerate less than the video output.
Scenario is play for N seconds, pause, flushing seek to some other position,
play again. Each of the play sequences would normally start at 0 with
the decklink time. As a result, the latest frame from the previous sequence
is kept alive waiting for it's timestamp to pass before either dropping
(if a subsequent frame in the new sequence overrides it) or displayed
causing the out of place frame to be displayed.
This is also supported by the debug logs from the decklink video sink
element where a ScheduledFrameCompleted() callback would not occur for
the frame until the above had happened.
It was timing related as to whether the frame was displayed based
on the decklink refresh cycle (which seems to be 16ms here),
when the frame was scheduled by the sink and the difference between
the 'time since vblank' of the two play requests (and thus start times
of scheduled playback).
https://bugzilla.gnome.org/show_bug.cgi?id=797130
This is now handled directly in gstaudiosrc/sink, and we were setting
it in the wrong thread anyway. prepare() is not the same thread as
sink_write() or src_read().
This adds "restore-crtc" property using which one
can restore previous crtc mode.
By default it is enabled, if CRTC was already
active with a valid mode and kmssink set a new mode
on CRTC using force-modesetting.
This helps user restore previous crtc mode and get
the previous session back after running a kmssink
pipeline involving a force-modesetting.
For e.g. When running a kmssink pipeline on rpi
using force-modesetting on tty console, it was giving
a blank screen after pipeline, and now with help of restore-crtc
functionality, CRTC is set with previous crtc mode
previously active on tty console.
Edited-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
https://bugzilla.gnome.org/show_bug.cgi?id=797025
This allow setting properties that contains spaces. The spaces are
replaced with '-'. As an example, one can set the connector proper
"scaling mode" with the following:
... ! kmssink connector-properties="s,scaling-mode=1"
https://bugzilla.gnome.org/show_bug.cgi?id=797027
Can be used to pass custom connector properties to DRM. Properties can
be enumerated using modetest tool. These properties can then be applied
with the following gst-launch-1.0 syntax. Note that the name of the
structure is ignored.
... ! kmssink connector-properties="s,props1=value,props2=value"
https://bugzilla.gnome.org/show_bug.cgi?id=797027
drmModeGetFB returns -EINVAL for multi-planar framebuffers. Instead of
depending on the framebuffer dimensions to select the mode, use width
and height from GstVideoInfo, which was used to create the framebuffer
in the first place. This enables kmssink to display multi-planar
formats such as I420 or NV12 with modesetting enabled.
https://bugzilla.gnome.org/show_bug.cgi?id=796985
Since both audio and video capture devices declare the KSCATEGORY_CAPTURE interface,
plugging a camera that supports both could result in an audio device being mistaken
for a video one.
https://bugzilla.gnome.org/show_bug.cgi?id=796958
With the Windows 8.1 SDK, the v1 of the AUDCLNT_STREAMOPTIONS enum is
defined which only has NONE and RAW, so it's not only defined when
AudioClient3 is available.
Add a meson check for the symbol. This is not needed for Autotools
because there we build against the MinGW audioclient.h which is still
at v1 of the AudioClient interface.
The mxsfb-drm driver has been added to the kernel long ago and will now
be the default display driver for NXP i.MX28, i.MX6SX and i.MX7D
processors so now is a good time to add it to kmssink.
Also, this is used in the upcoming i.MX8MQ and i.MX8MM processors.
https://bugzilla.gnome.org/show_bug.cgi?id=796873
Otherwise decklink seems to hold onto the latest frame and may cause a
flash in the output if the played sequence has a framerate less than the
video output.
Scenario is play for N seconds, pause, flushing seek to some other position,
play again. Each of the play sequences would normally start at 0 with
the decklink time. As a result, the latest frame from the previous sequence
is kept alive waiting for it's timestamp to pass before either dropping
(if a subsequent frame in the new sequence overrides it) or displayed
causing the out of place frame to be displayed.
This is also supported by the debug logs from the decklink video sink
element where a ScheduledFrameCompleted() callback would not occur for
the frame until the above had happened.
It was timing related as to whether the frame was displayed based
on the decklink refresh cycle (which seems to be 16ms here),
when the frame was scheduled by the sink and the difference between
the 'time since vblank' of the two play requests (and thus start times
of scheduled playback).
Use async_depth for latency calcuation instead of
the length of Tasks array which could be NULL since we
don't do the msdk decoder init in set_format().
According to MediaSDK specification,
Width must be a multiple of 16 and Height must be a multiple
of 16 for progressive frame sequence and a multiple of 32 otherwise.
This patch sets a 16 bit alignment for width and 32 bit alignment
for height as default.
https://bugzilla.gnome.org/show_bug.cgi?id=796566
