If ctts (CompositionOffsetBox) has larger sample_offset
(offset between PTS and DTS) than (2 * duration) of the stream,
assume the ctts box to be corrupted and ignore the box.
https://bugzilla.gnome.org/show_bug.cgi?id=797262
This fixes a bug where in some files mehd.fragment_duration is one unit
less than the actual duration of the fragmented movie, as explained below:
mehd.fragment_duration is computed by scaling the end timestamp of
the last frame of the movie in (in nanoseconds) by the movie timescale.
In some situations, the end timestamp is innacurate due to lossy conversion to
fixed point required by GstBuffer upstream.
Take for instance a movie with 3 frames at exactly 3 fps.
$ gst-launch-1.0 -v videotestsrc num-buffers=3 \
! video/x-raw, framerate="(fraction)3/1" \
! x264enc \
! fakesink silent=false
dts: 999:59:59.333333334, pts: 1000:00:00.000000000, duration: 0:00:00.333333333
dts: 999:59:59.666666667, pts: 1000:00:00.666666666, duration: 0:00:00.333333334
dts: 1000:00:00.000000000, pts: 1000:00:00.333333333, duration: 0:00:00.333333333
The end timestamp is calculated by qtmux in this way:
end timestamp = last frame DTS + last frame DUR - first frame DTS =
= 1000:00:00.000000000 + 0:00:00.333333333 - 999:59:59.333333334 =
= 0:00:00.999999999
qtmux needs to round this timestamp to the declared movie timescale, which can
ameliorate this distortion, but it's important that round-neareast is used;
otherwise it would backfire badly.
Take for example a movie with a timescale of 30 units/s.
0.999999999 s * 30 units/s = 29.999999970 units
A round-floor (as it was done before this patch) would set fragment_duration to
29 units, amplifying the original distorsion from 1 nanosecond up to 33
milliseconds less than the correct value. The greatest distortion would occur
in the case where timescale = framerate, where an entire frame duration would
be subtracted.
Also, rounding is added to tkhd duration computation too, which
potentially has the same problem.
https://bugzilla.gnome.org/show_bug.cgi?id=793959
There is no specific needs to duplicate the FD. Unlike the exportation,
we don't depend on code that will call close. This will make debugging
easyer since the traced FD will match the exporter.
... before the old streams is not exposed yet for MSS stream.
In case of DASH, newly configured streams will be exposed
whenever demux got moov without delay.
Meanwhile, since there is no moov box in MSS stream,
the caps will act like moov. Then, there is delay for exposing new pads
until demux got the first moof.
So, following scenario is possible only for MSS but not for DASH,
STREAM-START -> CAPS -> (configure stream but NOT EXPOSED YET)
-> STREAM-START-> CAPS (configure stream again).
In above scenario, we can reuse old stream without any stream reconfigure.
https://bugzilla.gnome.org/show_bug.cgi?id=797239
Apart from the obvious drawbacks of hardcoding, the drawback here was
that, if we subtracted 2 frames (instead of 2.6) from the target running
time, we'd request the next keyframe a bit too far into the future,
which would make our files split at the wrong position.
https://bugzilla.gnome.org/show_bug.cgi?id=797293
Flv does not support various channels in AAC stream format, for example
flvdemux detect an audio channels of 2(stereo) when the AAC really is 1(mono).
https://bugzilla.gnome.org/show_bug.cgi?id=797275
Flv does support changing the stream type and stream properties
after the headers were started to be written, and for example H264
codec_data changes can be supported.
https://bugzilla.gnome.org/show_bug.cgi?id=797256
For drop-frame framerates, when the expected next max timecode wraps
around at the end of the day, we have to subtract the offset of the
daily jam, otherwise we end up with a duration that's a few frames too
long.
https://bugzilla.gnome.org/show_bug.cgi?id=797270
