The previous code could enter an infinite loop because the adapter state
could get out of sync with its mapped data state after sync was lost.
The code was pretty confusing so it's been rewritten to be clearer.
The easiest way to reproduce the infinite loop is to use the breakmydata
element before tsdemux to trigger a resync.
https://bugzilla.gnome.org/show_bug.cgi?id=708161
Some streams had wrong values for the stream_id_extension, make sure
we only remember the valid ones.
For streams with PES_extension_field_length == 0, assume there's nothing
else.
For streams that state they have a TREF extension but don't have enough
data to store it, just assume it was produced by a non-compliant muxer
and skip the remaining data.
Only store remaining data in stream_id_extension_data instead of storing
data we already parse.
If ever we lose sync, we were just checking for the next 0x47 marker ...
which might actually happen within a mpeg-ts packet.
Instead check for 3 repeating 0x47 at the expected packet size interval,
which the same logic we use when we initially look for the packet size.
We were only resetting the first 512 values of the lookup table instead
of the whole 8192.
This resulted in any PCR PID over 0x0200 ... ending up taking the first PCR
table around :(
ATSC ac3 streams are always guaranteed to be AC3 if EAC3 descriptor
is not present
If stream registration id is 'AC-3' then it's also guaranteed to be AC3.
Finally if AC3 descriptor is present it's guaranteed to be AC3.
Only silences a warning, but still.
We know we will not overflow 64 bits, therefore just use direct
multiplication/division instead of the scale method (trims usage from
50 instruction calls to 2/3).
Helps with debugging issues. And also remove unused variable (opcr)
This will also allow us in the future to properly detect:
* random-access location (to enable keyframe observation and
potentially seeking
* discont location (to properly handle resets)
* splice location (to properly handle new stream changes)
The new seek handling re-creates the segment time information once it
has enough information after a seek.
The problem was that we'd completely ignore the requested rate. So store
that and use it in the newly created segment.
https://bugzilla.gnome.org/show_bug.cgi?id=694369
The program_number attribute was overloaded, trying to indicate both
the currently playing program, and the program requested via the
"program-number" property. The end result was that setting the
property didn't work (see #690934).
I added a new requested_program_number field rather than reviving the
current_program_number field because it seemed this would result in
fewer changes overall and be less confusing. It breaks symmetry with
the "program-number" property, but it retains parallels with the likes
of program->program_number.
Because gst_ts_demux_reset is called after the properties have been
parsed, requested_program_number is initialised in gst_ts_demux_init.
Whether this is exactly the right place, I don't know.
Setting the program-number property does not affect which program
is actually being demuxed.
Moving the initialization of the program_number from
gst_ts_demux_reset to gst_ts_demux_init seems to fix this issue.
https://bugzilla.gnome.org/show_bug.cgi?id=690934
* Avoids handling twice the same seek (can happen with playbin and files
with subtitles)
* Set the sequence number of the segment event to the sequence number of
the seek event that generated it (-1 for the initial one).
The seeking start time is approximated from the seek offset in bytes
using the accumulated PCR observations, so on a VBR stream there might
be a big difference between the actual PCR and the estimated one after
the seek. This might result in a long wait to skip all out of segments
packets.
Instead we just recalculate the new segment to start at the first PTS
after the seek, so that playback starts immediatly.
This is actually a workaround (we'll be skipping the upcoming section)
This will only happen for sections where the beginning is located within
the last 8 bytes of a packet (which is the minimum we need to properly
identify any section beginning).
Later we should figure out a way to store those bytes and mark that
some analysis needs to happen. The probability of this happening is
too low for me to care right now and do that fix. There is a good chance
that section will eventually be repeated and won't end up on such border.
* packet.origts is no longer used since the PCR refactoring done ages ago
* known_packet_size is a duplicate of packet_size != 0
* caps was never used outside of the packetizer
We had two issues with the previous code:
1) We were badly handling PUSI-flagged packets. We were discarding the
initial data (if pointer != 0) whereas we should have been accumulating
it with the previous data (if there was a continuity of course).
=> First series of information loss
2) We were not checking whether there were more sections after the end
of one (i.e. when the following byte was not a stuff byte).
This fixes those two issues.
Fixes#677443https://bugzilla.gnome.org/show_bug.cgi?id=677443
Until now we simply ignored those streams (since we couldn't do anything
with it anyway). Now that we have the mpegts library and we offload the
section handling to the application side we can properly identify and
extract them.
By default it is disabled for tsparse and enabled for tsdemux, but there is
a property to change that.
This should open the way to properly handle all private section streams,
including:
* DSM-CC
* MHEG
* Carousel data
* Metadata streams (though I haven't seen any of those in the wild)
* ... And all other specs/protocols making use of those
Partially fixes#560631
Since we now send all sections to the packetizer, we no longer need to do
anymore in-depth checks for the validity of a section.
The choice boils down to:
1) Is it from a known PES pid ? If so pass it on (which might be just pushing
downstream in the case of tsparse, or accumulating PES data for tsdemux)
2) Is it from a known SI pid ? If so pass it to the section packetizer
We still have some other stream types which haven't been ported, but
we will do so once we have defined the enums in the mpegts library.
Also add some FIXMEs regarding items discovered during analysis
* Only mpeg-ts section packetization remains.
* Improve code to detect duplicated sections as early as possible
* Add FIXME for various issues that need fixing (but are not regressions)
https://bugzilla.gnome.org/show_bug.cgi?id=702724
We use add_stream(stream_type:-1) to ensure a programs' PCR Stream is
also taken into account. For most programs this will re-use an
existing ES stream.
So only warn that we are re-adding a stream if it was already present
AND it is not to ensure the PCR stream is taken into account.
Only create subtables when needed. It was previously creating one every
single time ... to check if one was present.
And speed up code to detect whether a subtable was already present or not.
Overall makes section pushing 2 times faster.
