Returning MFX_ERR_INCOMPATIBLE_VIDEO_PARAM from
MFXVideoDECODE_DecodeFrameAsync means the allocated mfx surface is not
suitable for the current frame, we need a new mfx surface and try
MFXVideoDECODE_DecodeFrameAsync again.
When MFXVideoDECODE_DecodeFrameAsync () returns MFX_WRN_DEVICE_BUSY with
an output surface, a new input surface is required when retrying
MFXVideoDECODE_DecodeFrameAsync ().
This fixes the out-of-surface issue mentioned in
https://gitlab.freedesktop.org/gstreamer/gst-plugins-bad/issues/890
This gets rid of annoying message in the log, e.g. run the pipeline
below:
gst-launch-1.0 videotestsrc num-buffers=100 ! \
video/x-raw,format=NV12,width=352,height=288 ! msdkh264enc ! filesink \
location=test.h264
[LIBVA]:CRITICAL - DdiMedia_DestroyImage:4357: Invalid image
This make the pipeline below works:
gst-launch-1.0 videotestsrc num-buffers=1 ! msdkvpp ! \
video/x-raw,format=UYVY ! filesink location=a.yuv
Once https://github.com/intel/media-driver/pull/526 in the media-driver
is merged, the pipeline below also works:
gst-launch-1.0 videotestsrc num-buffers=1 ! msdkvpp ! \
video/x-raw\(memory:DMABuf\),format=UYVY ! filesink location=a.yuv
An output surface is returned but without sync point when when
MFXVideoDECODE_DecodeFrameAsync () returns MFX_ERR_MORE_DATA, this
surface should be released too, otherwise the surface is occupied
and it is easy to exhaust all pre-allocated mfx surfaces.
Example pipeline (input_vp8.webm contains lots of frame with show_frame
set to 0):
gst-launch-1.0 filesrc location=input_vp8.webm ! matroskademux !
msdkvp8dec ! msdkvpp ! fakesink
0:00:05.995959693 19866 0x563f30f14590 ERROR default
gstmsdkvideomemory.c:77:gst_msdk_video_allocator_get_surface: failed to
get surface available
ERROR: from element
/GstPipeline:pipeline0/GstMatroskaDemux:matroskademux0: Internal data
stream error.
The input buffer is released in gst_msdkdec_finish_task () when decoding
some special clips however this buffer is still in use, so ref the input
buffer before gst_msdkdec_finish_task () and unref it at the end of
gst_msdkdec_handle_frame ().
Fixes https://gitlab.freedesktop.org/gstreamer/gst-plugins-bad/issues/862
The picture structure in the output parameters from
MFXVideoDECODE_Query is set to MFX_PICSTRUCT_UNKNOWN for some codecs, so
the structure of the corresponding mfx surfaces created for decoding are
unknown. The pipeline will be broken when these surfaces are used as the
input for msdkvpp.
Example pipeline:
gst-launch-1.0 filesrc location=input_vp8.webm ! matroskademux !
msdkvp8dec ! msdkvpp ! fakesink
Error message:
0:00:00.031568911 14259 0x55b79dc684a0 ERROR msdkvpp
gstmsdkvpp.c:728:gst_msdkvpp_transform:<msdkvpp0> MSDK Failed to do VPP
ERROR: from element
/GstPipeline:pipeline0/GstMatroskaDemux:matroskademux0: Internal data
stream error.
This is a workaround for the above issue
The memory type was used as bitwise enum, but the enum was not
defined in that way.
Nonetheless, most of the usage of the memory type was as mutually
exclusive options, rather than option composition.
This patch refactor how the memory type is defined, so it is kept
the mutual exclusion among options.
When building the msdk plugin even if libmfx is found, unless the
plugin is explicitly enabled we should not error out if msdk
dependencies are not found.
Also give an error message when we don't build the plugin on Windows
because we're not building with MSVC.
BRCParamMultiplier in mfxInfoMFX is a parameter which specifies a
multiplier for bitrate control parameters [1], it impacts TargetKbps,
MaxKbps, BufferSizeInKB and InitialDelayInKB.
[1]: https://software.intel.com/en-us/node/628473
According to the MSDK documation[1], MFXCloneSession is a light-weight
equivalent of MFXJoinSession after MFXInit, so MFXJoinSession call isn't
needed in the msdk plugin, otherwise the cloned session is joined to the
parent session twice, and we will get a MFX error when closing the
parent session
example pipeline:
gst-launch-1.0 videotestsrc num-buffers=100 ! \
video/x-raw,format=NV12,width=352,height=288 ! msdkh264enc ! msdkh264dec ! \
msdkh264enc ! fakesink
Error message:
0:00:00.211948518 21733 0x5586ee741c60 ERROR msdk
msdk.c:148:msdk_close_session: Close failed (undefined behavior)
[1]: https://software.intel.com/en-us/node/628429#MFXCloneSession
In gst-msdk, a mfx session may be shared between different gst
elements, each element tries to set the frame allocator. However, per
the MSDK documation[1], the behavior is undefined if reset the frame
allocator while the previous allocator is in use. Fortunately all
elements use the same frame allocator, so we can avoid to call
MFXVideoCORE_SetFrameAllocator again.
[1]: https://software.intel.com/en-us/node/628430#MFXVideoCORE3
If so, BGRA is the preferred output format hence BGRA will be selected
as input format by default, e.g. in the pipleline below, BGRA instead of
NV12 is selected without renegotiation, so we can avoid the NV12 issue
(see commit 3f2314a) by default.
gst-launch-1.0 videotestsrc ! msdkvpp ! glimagesink
Otherwise MFXVideoVPP_Init will fail because it is called twice without
a close.
Example pipeline:
gst-launch-1.0 videotestsrc ! msdkvpp ! glimagesink
Sometimes glimagesink emits GST_EVENT_RECONFIGURE event which results
in that MFXVideoVPP_Init is called twice, then get the negotiation
failure below:
0:00:00.093715518 21218 0x558ef56231e0 ERROR msdkvpp
gstmsdkvpp.c:995:gst_msdkvpp_initialize:<msdkvpp0> Init failed
(undefined behavior)
WARNING: from element /GstPipeline:pipeline0/GstMsdkVPP:msdkvpp0: not
negotiated
After applying this commit, the pipeline above may run without
negotiation failure, however NV12 layout in dmabuf mode is selected in
renegotiation, the display image is corrupted due to the NV12 issue which
was mentioned in commit 3f2314a. Some other fixes are needed to avoid
renegotiation by default
In general, we should assume any unhandled error is
non-recoverable.
In the flush frames loop, some error states can cause us
to never increment the task and therefore we get stuck
in an infinite loop and generate GST_ELEMENT_ERROR
over and over again. This eventually consumes all
system memory and triggers OOM. Thus, assume the worst
and break out of the loop upon the first "unhandled" error.
https://gitlab.freedesktop.org/gstreamer/gst-plugins-bad/issues/859
We will add more profiles in the sink caps of msdkh265enc, so let
msdkh265enc re-add the sink pad template. Note this change doesn't
impact any capability
CodecProfile will be set in MFXVideoDECODE_DecodeHeader() to match
the input stream. Setting the hard-coded profile here will mislead
user that msdkh265dec supports a special profile only.
Previously alloc_info is initialized when both thiz->initialized
and thiz->allocation_caps are true, but only thiz->initialized is
checked when alloc_info is used.
MediaSDK has been released as open source [1], but the directories
where it installs its files, are different from the binary only
distribution.
This patch adds to the libraries path the directory /lib. Also it
is defined in meson if the include directory has the mfx/ prefix,
something that is already handled in autotools.
1. https://github.com/Intel-Media-SDK/MediaSDK
the 2018.3.1 intel sdk release places libraries into /lib64 instead of
/lib/lin_x64 or /lib/x64, this commit adds /lib64 to the libdir
locations list
Fixes#815
Use async_depth for latency calcuation instead of
the length of Tasks array which could be NULL since we
don't do the msdk decoder init in set_format().
According to MediaSDK specification,
Width must be a multiple of 16 and Height must be a multiple
of 16 for progressive frame sequence and a multiple of 32 otherwise.
This patch sets a 16 bit alignment for width and 32 bit alignment
for height as default.
https://bugzilla.gnome.org/show_bug.cgi?id=796566
In cases where we do hard resest, the current code destroys the frame
which has new resolution bit early and this causes buffer_unmap
warnings. Keep an extra ref to the frame internally to avoid this.
The gst-msdk decoders only support packetized formats for
all codecs except VC1. For VC1, it supports codec_data for advanced
profiles and this codec_data wan't submitting to MSDK's DecodeHeader APIs.
Make sure the subclass deocders correctly configured so that
the codec_data buffers are in place in the internal adapter for
MediaSDK's DecoderHeader usage.
Currently we use the gst_video_decoder_get_oldest_frame()
to get the old pending frame to output. But this is not correct
if pts re-ordering required. This patch uses a custom made
get_old_frame() which accounts the PTS too similar to the
v4l2decoder.
https://bugzilla.gnome.org/show_bug.cgi?id=796699
The patch adds a serios of changes to support dynamic resolution
change and efficient utilization of resources.
Major changes:
-- Use MSDK's apis to retrieve the headers instead of only relying
on upsteram notification. For eg: avc decoder requires SEI header
information for dpb count calculation which we don't get from caps.
-- For all codecs other than VP9, we force the reset of decoder
if resoultion changes to fit with gstreamer flow. VP9 enfource
the hard reset only if the new resolution is bigger.
-- delay the src caps setting till msdk api's invokation in
handle_frame to avoid caching multiple configuration values
-- ensure pool negotiation is based on decoder's allocation_caps.
--dynamic resoluttion change use an explicit allocation_query
to reclaim the buffers before closing the decoder (thanks to v4l2dec)
--In case if we don't get upstream notification of res change (for eg,
this can can happen for vp9 frames with ivfheader where ivfparse
is not able to notify the dynamic changes), we handle the the case
based on MFX_ERR_INCOMPATIBLE_VIDEO_PARAM which is the return value
of MFXVideoDECODE_DecodeFrameAsync
-- calculate the minimum surfaces to be preallocated based on
msdk suggestion, downstream requirement, async depth and scratch surface
count for smooth display.
https://bugzilla.gnome.org/show_bug.cgi?id=796566
According to msdk spec, there are two ways to enable filters:
1: Filters can be enabled by adding a filter ID
to mfxExtVPPDoUse. In this case, default filter parameters are used
2: Add filter configuration structures directly to mfxVideoParam.
Using 1 with 2 is optional but legal. Unfortunately it won't work
with some specific use cases like Detail/EdgeEnhancement.
Let's stick with option2 which works fine for all VPP operations.
https://bugzilla.gnome.org/show_bug.cgi?id=796468
Since we do the MSDK initializing in set_caps(), a FALSE
return may still cause the invokation of set_caps() again
and this will leads to buffer allocation and other mess-up.
So make sure the msdk initialized correctly before trying
to do any buffer allocation.
https://bugzilla.gnome.org/show_bug.cgi?id=796465
Make sure all the enabled filter structures are added in the
mfxVideoParm before doing the VPPQuery so that msdk
can do the input param validation
https://bugzilla.gnome.org/show_bug.cgi?id=796465
