Currently in rtp_session_send_rtp(), the existing ntp-64 RTP header
extension timestamp is updated with the actual NTP time before sending
the packet. However, there are some circumstances where we would like
to preserve the original timestamp obtained from reference timestamp
buffer metadata.
This commit provides the ability to configure whether or not to update
the ntp-64 header extension timestamp with the actual NTP time via the
update-ntp64-header-ext boolean property. The property is also exposed
via rtpbin. Default property value of TRUE will preserve existing
behavior (update ntp-64 header ext with actual NTP time).
Fixes https://gitlab.freedesktop.org/gstreamer/gstreamer/-/issues/1580
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/3451>
Previously we tried to route an incoming RTCP FB FIR to the correct ssrc
using the "media source" component of the RTCP FB message. However,
according to RFC5104 (section 4.3.1.2) the "media source" SHALL be set
to 0. Instead the ssrc(s) in use are propagated via the FCI data. Now
a specific GstForceKeyUnit event is sent for every ssrc.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/3292>
RTP source statistics are tracked for local senders by
treating them as a receiver of their own outbound packets.
Accordingly, track the highest packet seqnum so that the
packets-lost calculation generates a sensible number instead
of always reporting -$number_of_packets_sent
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/3454>
When getting a "404 Not Found" response from the DESCRIBE request, the
source produced a "No supported authentication protocol was found" error
instead of passing on the 404, which was confusing.
Only produce this error message when we're handling a response of "401
Unauthorized" without a compatible WWW-Authenticate header.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/3414>
The only case where we definitely need to write a new trun is when the
data_offset value does not match the end of the list of entries.
Needing multiple trun atoms is required when interleaving multiple
streams together.
All other cases can be covered by adding more entries to the existing
trun atom.
Fixes playback of fragemented mp4 in ffplay and chrome.
Using e.g. mp4mux fragment-duration=1000 fragment-mode=dash-or-mss
and
mp4mux fragment-duration=1000 fragment-mode=first-moov-then-finalise
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/3426>
In order to figure out if the "raw" audio contained within the wav
container is actually DTS, wavparse calls the typefinder helper
except that means it runs all typefinders.
Since it only cares about checking for DTS, we should only run the
audio/x-dts typefinder (if present). Commit 858e516 did not really
fix things.
Use the new type helper with the caps to fix this.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/3417>
Set udpsrc seqnums on all events sent to the udpsrc's, and before
forwarding events out of rtspsrc set the latest seek seqnum on them if
any.
Also produce a consistent seqnum in rtspsrc from the very beginning.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/3409>
This is small regression from commit f7abd81a.
When calling `gst_element_query()` no pad is associated with that query, but the
current code always forwards the query to the associated pad, which is NULL in
previous case. This patch checks for the pad before forwarding the query.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/3404>
In a few cases throughout qtdemux, the results of QT_UINT32 were being
stored in a signed integer, which could cause subtle bugs in the case of
an integer overflow, even allowing the the result to equal a negative
number!
This patch prevents this by simply storing the results of this function
call properly in an unsigned integer type. Additionally, we fix up the
length checking with stsd parsing to prevent cases of child atoms
exceeding their parent atom sizes.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/3344>
In order to figure out if the "raw" audio contained within the wav
container is actually DTS, right now we call the typefinder helper
which runs all typefinders.
Speed up this type finding process by specifying the extension.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/3294>
We've seen occasional crashes in the `wavparse` module associated with
referencing a buffer in `gst_wavparse_chain` that's already been freed. The
reference is stolen when the buffer is transferred to the adapter with
`gst_adapter_push` and, IIUC, assuming the source doesn't hold a reference to
the buffer, the buffer could be freed during interaction with the adapter in
`gst_wavparse_stream_headers`.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/3179>
in certain ways.
In the case that a test is provided for, the size of the `fmt ` chunk is
changed from 16 bytes to 18 bytes (bytes 17 - 20 below):
```
$ hexdump -C corruptheadertestsrc.wav
00000000 52 49 46 46 e4 fd 00 00 57 41 56 45 66 6d 74 20 |RIFF....WAVEfmt |
00000010 12 00 00 00 01 00 01 00 80 3e 00 00 00 7d 00 00 |.........>...}..|
00000020 02 00 10 00 64 61 74 61 |....data|
00000028
```
(Note that the original file is much larger. This was the smallest sub-file
I could find that would generate the crash.)
Note that, while the same issue doesn't cause a crash in pull mode, there's a
different issue in that the file is processed successfully as if it was a .wav
file with zero samples.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/3173>
This is a regression that was introduced in
cca2f555d1 (yes, 9 years ago).
The only place where a demuxer streaming thread should be stopped is when the
sinkpad is deactivated from pull mode (i.e. PAUSED->READY).
Attempting to stop the task in this function would cause this to happen when a
FLUSH_STOP or STREAM_START event is received... which can cause deadlocks.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/3109>
If the SETUP request returns an IPv6 server address in the Transport
field, we would generate an incorrect URI, and multiudpsink would fail
to initialize:
```
rtspsrc gstrtspsrc.c:9780:dump_key_value:<source> key: 'Transport', value: 'RTP/AVP;unicast;source=fe80::dc27:25ff:fe5e:bd13:8080;client_port=62696-62697;server_port=4000-4001'
...
rtspsrc gstrtspsrc.c:4595:gst_rtspsrc_stream_configure_udp_sinks:<source> configure RTP UDP sink for fe80::dc27:25ff:fe5e:bd13:8080:4000
...
multiudpsink gstmultiudpsink.c:1229:gst_multiudpsink_configure_client:<udpsink0> error: Invalid address family (got 23)
```
We can't look at stream->is_ipv6 because we can't rely on the server
returning the right value there. In the issue reported about this,
server reported itself as `KuP RTSP Server/0.1`, and the SDP was:
```
c=IN IP4
m=video 54608 RTP/AVP 96
a=rtpmap:96 H264/90000
```
So we need to parse the string value and figure out the family
ourselves.
Fixes https://gitlab.freedesktop.org/gstreamer/gstreamer/-/issues/1058
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1819>
Timers for RTX packets are dealt with later in update_rtx_timers(), and
timers for non-RTX packets would potentially also be unscheduled a
second time from there so avoid that.
Also don't shadow the timer variable from the outer scope but instead
make use of it directly.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2973>
When stopping the element, make sure the pad task
is stopped before destroying the part readers.
Closes a race where the pad task might access
a freed pointer.
Also add a guard against this sort of thing
by holding a ref to the reader in the pad loop.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2901>
That is, get rid of unnecessary and wrong special-casing.
This could always use gst_rtsp_url_get_request_uri_with_control() but as
we only have the control base URI as string it is easier to just call
gst_uri_join_strings().
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2868>
Otherwise we won't send the protection packets for the last few
packets when a stream ends.
Also send EOS on the FEC src row pad immediately, and on the FEC src
column pad after draining is complete. This makes it so that the FEC
src pads on rtpbin behave the same way as the RTCP src pads on rtpbin
when EOS is received on the send_rtp_sink pad.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2863>
With the 2.72 release, glib-networking developers have decided that
TLS certificate validation cannot be implemented correctly by them, so
they've deprecated it.
In a nutshell: a cert can have several validation errors, but there
are no guarantees that the TLS backend will return all those errors,
and things are made even more complicated by the fact that the list of
errors might refer to certs that are added for backwards-compat and
won't actually be used by the TLS library.
Our best option is to ignore the deprecation and pass the warning onto
users so they can make an appropriate security decision regarding
this.
We can't deprecate the tls-validation-flags property because it is
very useful when connecting to RTSP cameras that will never get
updates to fix certificate errors.
Relevant upstream merge requests / issues:
https://gitlab.gnome.org/GNOME/glib/-/merge_requests/2214https://gitlab.gnome.org/GNOME/glib-networking/-/issues/179https://gitlab.gnome.org/GNOME/glib-networking/-/merge_requests/193
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2494>
The caps negotiation should respect the selected method to the test pipeline below works properly.
gst-launch-1.0 videotestsrc ! video/x-raw,width=320,height=600 ! videoflip method=clockwise ! video/x-raw,width=600,height=320 ! fakesink
Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2803>
Various variables were of smaller types than needed and there were no
checks for any overflows when doing additions on the sizes. This is all
checked now.
In addition the size of the decompressed data is limited to 200MB now as
any larger sizes are likely pathological and we can avoid out of memory
situations in many cases like this.
Also fix a bug where the available output size on the next iteration in
the zlib decompression code was provided too large and could
potentially lead to out of bound writes.
Thanks to Adam Doupe for analyzing and reporting the issue.
CVE: tbd
https://gstreamer.freedesktop.org/security/sa-2022-0003.html
Fixes https://gitlab.freedesktop.org/gstreamer/gstreamer/-/issues/1225
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2610>
Various variables were of smaller types than needed and there were no
checks for any overflows when doing additions on the sizes. This is all
checked now.
In addition the size of the decompressed data is limited to 120MB now as
any larger sizes are likely pathological and we can avoid out of memory
situations in many cases like this.
Also fix a bug where the available output size on the next iteration in
the zlib/bz2 decompression code was provided too large and could
potentially lead to out of bound writes.
Thanks to Adam Doupe for analyzing and reporting the issue.
CVE: CVE-2022-1922, CVE-2022-1923, CVE-2022-1924, CVE-2022-1925
https://gstreamer.freedesktop.org/security/sa-2022-0002.html
Fixes https://gitlab.freedesktop.org/gstreamer/gstreamer/-/issues/1225
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2610>
If our downstream caps didn't intersect, we attempted to convert between
raw and ADTS stream formats, if possible. If the caps still did not
intersect, we then used the modified `src_caps` but left the
`output_header_type` unmodified.
This caused a mismatch between caps and actual stream format.
Avoid this by first copying the `src_caps` to `convcaps` for the
additional intersection tests, replacing `src_caps` if we succeed.
While we're here, clean up the code a bit and remove the `codec_data`
field from outgoing ADTS caps.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2550>
https://bugzilla.gnome.org/show_bug.cgi?id=741398 changed
rtpptdemux in 2014 to not post a GST_ELEMENT_ERROR on the
bus when dropping an invalid (non-RTP) packet, but still
returned GST_FLOW_ERROR upstream - so the pipeline still
stops, but now without a useful bus error.
Return GST_FLOW_OK instead, so the pipeline keeps
running. Some old telephony equipment can send invalid
packets before the real RTP traffic starts.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2520>
When processing the first event after probing the
file and being activated, requeue sticky events
as there's no requirement that demuxers send tag
and other events again after a seek - that's
why they're sticky.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2432>
- Consistently unref the chained buffer at the end of the chain
function, if we're not handing it off to `gst_pad_push`. This avoids a
few buffer leaks in the error paths in `_chain` and `_push_history`.
- When mapping the video frame fails, return a flow error instead of
crashing.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2428>
If we just break the loop, we might run into the `gop != NULL` assert
that follows it. Rather, exit immediately with flushing flow.
Also use this flushing mechanism when we release a pad. This avoids
having an extra flag.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1030>
The timestamp in the tfdt refers to the first trun box and if there are
multiple trun boxes then the distance between the first timestamps will
grow.
At some point this distance reaches a threshold and triggers the
resetting of the first sample's timestamp of this trun box to be reset
to the tfdt.
This threshold is implemented for files where there is a jump in the
timeline between fragments and where this can be detected via a jump
between the end timestamp of the previous fragment and the tfdt of the
next. This behaviour is preserved.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2409>
mp4mux can't negotiate caps with upstream/downstream and always outputs
specific caps based on the input streams. This will always happen before
it produces the first buffers.
By having the default aggregator negotiation enabled the same caps
would be pushed twice in the beginning, and again every time a
reconfigure event is received.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2372>
flvmux can't negotiate caps with upstream/downstream and always outputs
specific caps based on the input streams. This will always happen before
it produces the first buffers.
By having the default aggregator negotiation enabled the same caps
would be pushed twice in the beginning, and again every time a
reconfigure event is received.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2372>
Mixing C loops with switch statements is a bad idea as break has a
different meaning in both. Breaking inside the switch statements wrongly
caused further loop iterations.
Instead use goto to get out of the loop and continue to do another loop
iteration, and never ever use break except for the end of a case.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2336>
In push mode (streaming), if the received chunk buffer size from _chain is bigger
than output buffer size, the flags of the divided-buffers are propagated to the
DISCONT flag from first received chunk buffer. This unexpected buffers contained DISCONT
flags are abnormally transformed when changing the sampling rate by audioresample element.
So unset unnecessary DISCONT flag before pad_push().
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2305>
Previously, we only added it when actually performing synchronization
based on the NTP time.
The information can be useful downstream in other situations too, and
we can compute a NTP time as soon as we get a sender report with the
relevant information.
Co-authored-by: Mathieu Duponchelle <mathieu@centricular.com>
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2252>
When the sink is configured to create sockets with an explicit bind
address, then the created socket gets set to the udp_socket field
irregardless of whether the bind address indicated that the socket
family should be IPv4 or IPv6. When binding to an IPv6 address, this
results in the following error:
gstmultiudpsink.c:1285:gst_multiudpsink_configure_client:<rtcpsink>
error: Invalid address family (got 10)
This patch adds a check of the address family being bound to and sets
the created socket to used_socket or used_socket_v6, accordingly.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1551>
The RTCP SR packet might be without SDES in case of a reduced-size RTCP
packet. For syncing purposes the CNAME is needed but it might be known
already from an earlier RTCP packet or out of band, via the SDP for
example.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2132>
GLib guarantees libintl is always present, using proxy-libintl as
last resort. There is no need to mock gettex API any more.
This fix static build on Windows because G_INTL_STATIC_COMPILATION must
be defined before including libintl.h, and glib does it for us as part
as including glib.h.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2028>
They are part of gst_dep already and we have to make sure to always have
gst_dep. The order in dependencies matters, because it is also the order
in which Meson will set -I args. We want gstreamer's config.h to take
precedence over glib's private config.h when it's a subproject.
While at it, remove useless fallback args for gmodule/gio dependencies,
only gstreamer core needs it.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/2031>
Represents touchscreen events as a trail of black squares, one for each
reported position. Additionally, this adds the `display-mouse` and
`display-touch` properties to toggle visibility of mouse/touchscreen
events, since touchscreens often emulate mouse events, as well as
logging for all received navigation events.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1633>
Two RTP Header extensions are very relevant for rtprtxsend/receive.
1. "urn:ietf:params:rtp-hdrext:sdes:rtp-stream-id": will always be removed
2. "urn:ietf:params:rtp-hdrext:sdes:repaired-rtp-stream-id": will be written
instead of the "rtp-stream-id" header extension.
Currently it's only a simple replacement of one header extension for
another however a future change would only add the relevant extension
based on some heuristics (like, video frames only on one of the rtp key
frame buffers, or only until the rtx ssrc has been validated by the peer)
in order to reduce the required bandwidth.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1759>
When syncing to an RFC7273 clock this will add the original
reconstructed reference clock timestamp to buffers in form
of a GstReferenceTimestampMeta.
This is useful when we want to process or analyse data based
on the original timestamps untainted by any local adjustments,
for example reconstruct AES67 audio streams with sample accuracy.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1964>
When syncing to an RFC7273 clock this will add the original
reconstructed reference clock timestamp to buffers in form
of a GstReferenceTimestampMeta.
This is useful when we want to process or analyse data based
on the original timestamps untainted by any local adjustments,
for example reconstruct AES67 audio streams with sample accuracy.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1964>
When syncing to an RFC7273 clock this will add the original
reconstructed reference clock timestamp to buffers in form
of a GstReferenceTimestampMeta.
This is useful when we want to process or analyse data based
on the original timestamps untainted by any local adjustments,
for example reconstruct AES67 audio streams with sample accuracy.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1964>
Previously the result of the calculations included inaccuracies caused
by the NTP clock estimation, which caused the timestamps to jitter
+/- 1/clockrate.
By reorganizing the calculations it is possible to get rid of this
inaccuracy and calculate deterministic and exact packet timestamps based
on the actual NTP clock as long as the estimation is not off by more
than 2**31 clockrate units.
The only remaining inaccuracy that is introduced now is caused by the
conversion from the NTP clock to the pipeline clock.
Also split up debug output, demote many messages to the trace debug
level and output more intermediate results.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1955>
This is difficult to encounter in ordinary networks, but is
encountered when using tc-netem to add random delays to packets, and
also when your UDP stream is bonded over multiple links with varying
characteristics.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1952>
Gapless playback is handled by adjusting buffer timestamps & durations
and by adding GstAudioClippingMeta.
Support for "Frankenstein" streams (= poorly stitched together streams)
is also added, so that gapless playback support doesn't prevent those
from being properly played.
Co-authored-by: Sebastian Dröge <sebastian@centricular.com>
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1028>
This patch fixes a seg.fault in gst_structure_new() with warnings as below.
GLib-GObject-WARNING **:
../gobject/gtype.c:4330: type id '0' is invalid
GLib-GObject-WARNING **:
can't peek value table for type '<invalid>' which is not currently referenced
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1918>
The point here is that rtpsession will create a new rtpsource when
the field "rtx-ssrc" is present, and when not doing rtx, that means
a random ssrc will create a new rtpsource that will be included in RTCP
messages for the current session.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1882>
When doing only a single stream of audio/video this hardly matters,
but when doing many at the same time, the fact that you have to get
a hold of the glib global type-system lock every time you process a buffer,
means that there is a limit to how many streams you can process in
parallel.
Luckily the fix is very simple, by doing a cast rather than a full
type-check.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1873>
Not having this field is equivalent with it being 1/1 so consider
it like that. The generic caps functions are not aware of these
semantics and would consider the caps different, causing a negotiation
failure when caps are changing from caps with to caps without or the
other way around.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1826>
Not having these fields is equivalent with them being mono/0 so consider
them like that. The generic caps functions are not aware of these
semantics and would consider the caps different, causing a negotiation
failure when caps are changing from caps with to caps without or the
other way around.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1826>
If the tracks element was parsed from the SeekEntry, don't
parse it a second time and recreate tracks, as this
loses any tags that were read using the seek table.
If a genuinely new Tracks element is found, do read that
as it is needed for MSE support.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1798>
LOAD macro relies in m7 being zero for interleaving purposes. Using LOAD
on the m7 register makes it interleave with its new content instead of
with 0.
The effect of this bug was bobbing on some static lines that appeared
over fast-moving content.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1816>
This allows downstream of a payloader to know the RTP header's marker
flag without first having to map the buffer and parse the RTP header.
Especially inside RTP header extension implementations this can be
useful to decide which packet corresponds to e.g. the last packet of a
video frame.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1776>
The RTP payload seems to be required as it carries the frame count
information. Also, gst_rtp_base_payload_allocate_output_buffer had
the second argument incorrect.
Strangely some devices like Shanling MP4 and Sony XM3 would still
work without this while some like the Sony XM4 do not.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1797>
Each stream may have its own segment timeline
(i.g., different segment.start or segment.base)
depending on edit-list and composition-to-decode atom.
Make sure whether time position of a stream has been actually
far behind than that of current target stream.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1352>
Constantly updating the ts_offset results in audiable glitches
when streaming audio using ntp-sync=true. By requiring a minimum
offset before updating ts_offset this can be mitigated. Added a
parameter which can be used to set min_ts_offset in ntp-sync mode.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1409>
When multiple streams are bundled together, there may be more
than one red payload type to handle.
In addition, as the red decoder works by filling in gaps in
the seqnums, there needs to be one rtp_history queue per sequence
domain.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1429>
In redenc, when input buffers have a header for the TWCC extension,
we now add one to our wrapper buffers.
In ulpfecenc we add one in that case to our protection buffers.
This makes TWCC functional when UlpRed is used in webrtcbin.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1414>
In order to allow "level-asymmetry-allowed" we now handle a new
"profile" field, which as the same semantics as the "profile" field in
H.264 stream so that we can force payloaded stream to have the right
format when using the `gst_sdp_media_get_caps_from_media` to set caps
filter after the payloader. This allows a simple negotiation in standard
RTP negotiation based on SDPs (like webrtc) for that particular case,
closely respecting the specs.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1410>
since `gst_caps_replace()` and `gst_pad_set_caps()` both ref the caps and neither of them takes the ownership of the caps -> it must be unreffed in `gst_multi_file_src_set_property()`
to test the leak (on Unix): `echo coucou > /tmp/file.txt && GST_TRACERS=leaks GST_DEBUG="GST_TRACER:7" gst-launch-1.0 multifilesrc location=/tmp/file.txt caps='txt' ! fakesink`
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1436>
Follow-up on 97d83056b3, only check
for intersection with the current srccaps when checking if a sinkpad
can accept caps.
I must have been lucky in my firefox testing then, and always entered
the code path with audio getting negotiated first, thus not failing
the is_subset check when srccaps had been negotiated as
application/x-rtp, and an accept-caps query was made for the video
caps with a defined extmap.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1384>
A previous patch has caused rtpfunnel to output twcc-related
information downstream, however this leaked into upstream
negotiation (through funnel->srccaps), causing payloader to
negotiate twcc caps even when not prompted to do so by the user.
Fix this by only enforcing that upstream sends us application/x-rtp
caps as was the case originally.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1278>
Negative composition time offsets are only allowed with version 1 of the
box, however we parse it as a signed value also for version 0 boxes as
unfortunately there are such files out there and it's unlikely to have
(valid) huge composition offsets.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1294>
g_sequence_remove_range's end iter is exclusive, so if one
wants to remove that item as well, it should be called with
the next iter.
This could in theory fix an issue where:
* The sequence isn't entirely trimmed, with an old item lingering
* Following FEC packets are immediately discarded because they
arrived later than corresponding media packets, long enough for
seqnums to wrap around
* We now try to reconstruct a media packet with a completely obsolete
FEC packet, chaos ensues.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1341>
The pipeline flow for receiving looks like this:
rtpsession ! rtpssrcdemux ! session_fec_decoder ! rtpjitterbuffer ! \
rtpptdemux ! stream_fec_decoder ! ...
There are two places where a fec decoder could be placed.
1. As requested from the 'request-fec-decoder' signal: after rtpptdemux
for each ssrc/pt produced
2. after rtpssrcdemux but before rtpjitterbuffer: added for the
rtpst2022-1-fecenc/dec elements,
However, there was some cross-contamination of the elements involved and
the request-fec-decoder signal was also being used to request the fec
decoder for the session_fec_decoder which would then be cached and
re-used for subsequent fec decoder requests. This would cause the same
element to be attempted to be linked to multiple elements in different
places in the pipeline. This would fail and cause all kinds of havoc
usually resulting in a not-linked error being returned upstream and an
error message being posted by the source.
Fix by not using the request-fec-decoder signal for requesting the
session_fec_decoder and instead solely rely on the added properties for
that case.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1300>
WebVTT in ISO MP4 is specified in ISO 14496-30,
and needed for DASH support. It's stored in an
mp4 specific format. To handle it compatibly,
the wvtt boxes are converted back into WebVTT text
and pushed as application/x-subtitle-vtt
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1182>
Swap the `need_process` boolean check on qtdemux streams
for a direct function pointer to the splitting function,
so we can stop adding extra cases to the single growing
`gst_qtdemux_process_buffer()` function.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1182>
Instead of assuming that the PTS of a keyframe is the lowest PTS of a
GOP, wait until the DTS has passed this PTS and take the minimum PTS up
to that point. That way the minimum PTS of a GOP can be determined, at
least for closed GOP streams. Open GOP streams still can't be handled
properly.
By knowing the minimum PTS of each GOP, keyframes can be requested at
the correct time relative to the GOP (and thus fragment) start and
fragment overflow calculations can calculate the correct durations of
the GOPs.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/1005>
Since the base class now does the parsing, there is no need
to reproduce that code in all the subclasses, just pass the attributes
which are the only relevant bit anyway.
Also, only store the direction if the subclass accepted the caps
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/906>
