Since commit c971d1a9a (rtpsource: refactor bitrate estimation,
2010-03-02) bytes_received filed in RTPSourceStats is set but then never
used again, expose it so that it can be used by user code to verify how
many bytes have been received.
According to RFC3550 lower-level headers should be considered for
bandwidth calculation.
See https://tools.ietf.org/html/rfc3550#section-6.2 paragraph 4:
Bandwidth calculations for control and data traffic include
lower-layer transport and network protocols (e.g., UDP and IP) since
that is what the resource reservation system would need to know.
Fix the source data to accommodate that.
Assume UDPv4 over IP for now, this is a simplification but it's good
enough for now.
While at it define a constant and use that instead of a magic number.
NOTE: this change basically reverts the logic of commit 529f443a6
(rtpsource: use payload size to estimate bitrate, 2010-03-02)
adjust/port from rtph264pay and allow sending the configuration data at
every IDR
The payloader was stripping the configuration data when the
config-interval was set to 0. The code was written in such a way !(a >
0) that it stripped the config when it was set at -1 (send config_data
as soon as possible).
This resulted in some MPEG4 streams where no GOP/VOP-I was detected to
be sent out without configuration.
In reverse playback, we don't want to rely on the position of the current
keyframe to decide a stream is EOS: the last GOP we push will start with
a keyframe, which position is likely to be outside of the segment.
Instead, let the normal seek_to_previous_keyframe mechanism do its job,
it works just fine.
If a key unit seek is performed with a time position that matches
the offset of a keyframe, but not its actual PTS, we need to
adjust the segment nevertheless.
For example consider the following case:
* stream starts with a keyframe at 0 nanosecond, lasting 40 milliseconds
* user does a key unit seek at 20 milliseconds
* we don't adjust the segment as the time position is "over" a keyframe
* we push a segment that starts at 20 milliseconds
* we push a buffer with PTS == 0
* an element downstream (eg rtponviftimestamp) tries to calculate the
stream time of the buffer, fails to do so and drops it
When the seek event contains a (newly-added) trickmode interval,
and TRICKMODE_KEY_UNITS was requested, only let through keyframes
separated with the required interval
The primary video stream is used to select fragment cut points
at keyframe boundaries. Auxilliary video streams may be
broken up at any packet - so fragments may not start with a keyframe
for those streams.
The time_position field of the stream is offset by the media_start
of its QtDemuxSegment compared to the start of the GstSegment of
the demuxer, take it into account when making comparisons.
If the conflict is detected when sending a packet, then also send an
upstream event to tell the source to reconfigure itself.
Also ignore the collision if we see more than one collision from the same
remote source to avoid problems on loops.
Add a new property "do-aggregate"* to the H.264 RTP payloader which
enables STAP-A aggregation as per [RFC-6184][1]. With aggregation enabled,
packets are bundled instead of sent immediately, up until the MTU size.
Bundles also end at access unit boundaries or when packets have to be
fragmented.
*: The property-name is kept generic since it might apply more widely,
e.g. STAP-B or MTAP.
[1]: https://tools.ietf.org/html/rfc6184#section-5.7
Closes https://gitlab.freedesktop.org/gstreamer/gst-plugins-good/issues/434
If an rtx packet arrives that hasn't been requested (it might
have been requested from prior to a reset), ignore it so that
it doesn't inadvertently trigger a clock skew.
In the case of reordered packets, calculating skew would cause
pts values to be off. Only calculate skew when packets come
in as expected. Also, late RTX packets should not trigger
clock skew adjustments.
Fixes#612
mpegaudioparse suggests MP3 needs 10 or 30 frames of lead-in (depending on
mpegaudioversion, which we don't know here), thus provide at least 30 frames
lead-in for such cases as a followup to commit cbfa4531ee.
