Handle sprop-vps, sprop-sps and sprop-pps in caps instead of
sprop-parameter-sets.
rtph265pay works with byte-stream and hvc1 formats but not hev1 yet. It
handles profile-id, tier-flag and level-id in caps query.
https://bugzilla.gnome.org/show_bug.cgi?id=753760
The FLV header cannot be trusted to indicate video or
audio presence, as the comments already mention. Don't
delay pushing tags waiting for streams that might never
appear.
Tags are now pushed immediately after they change:
- After parsing an onMetaData script object
- After negotiating caps on a pad
https://bugzilla.gnome.org/show_bug.cgi?id=768440
As seen in the parent switch for object_type_id, the 4 possible values are
0x40, 0x66, 0x67 and 0x68. Fixing the nested switch to match these values.
Looks like it was a typo making them decimal instead of hexadecimal.
CID 1363328
Without, raw AAC can't be handled and we have some information available in
the decoder that most likely allows us to decode the stream in one way or
another. This is the same code already used by matroskademux for the same
reasons, and ffmpeg/vlc play such files just fine too by guesswork.
This is to handle cases where upstream handles the fragmented streaming in TIME
segments and sends us data with gaps within fragments. This would happen when dealing
with trick-modes.
When upstream (push-based, TIME SEGMENT) wishes to send discontinuous samples,
it must obey the following rules:
* The buffer containing the [moof] must have a valid GST_BUFFER_OFFSET
* The buffers containing the first sample after a gap:
* MUST start at the beginning of a sample,
* MUST have the DISCONT flag set,
* MUST have a valid GST_BUFFER_OFFSET relative to the beginning of the fragment.
https://bugzilla.gnome.org/show_bug.cgi?id=767354
If we consider the RTSP state, what can happen is that it is PLAYING but the
element already asynchronously tried to PAUSE and it just did not happen yet.
We would then override this setting to PAUSED (while the element actually is
in PAUSED) and set the RTSP state to PLAYING again. This would then cause us
to produce packets while the sinks are all PAUSED, piling up thousands of
packets in the rtpjitterbuffer and other elements and finally failing.
This is supposed to be either in the codec_data (avc stream format) or inside
the stream, and we extract it from there. It should not be set from a
property as it's stream specific.
https://bugzilla.gnome.org/show_bug.cgi?id=767789
The Session Data Protocol doesn't allow specifying a cipher for the
SRTCP, so it will use the SRTP one. In the "srtpenc" element the cipher
"aes-128-icm" is the default for SRTP and SRTCP, but if we want to have
an SRTCP with the "aes-256-icm" cipher then we also need to set the SRTP
cipher to "aes-256-icm", otherwise "aes-128-icm" will be used instead.
https://bugzilla.gnome.org/show_bug.cgi?id=767799
With non-time segments, it now assumes that the arrival time of packets
is not relevant and that only the RTP timestamp matter and it produces
an output segment start at running time 0.
https://bugzilla.gnome.org/show_bug.cgi?id=766438
No variables were added/removed. This was just a good excuse to:
* Comment what most variables are used for (and when)
* Order them in such a way as to show first the common variables used
in all cases, followed by those only used in push-mode
We shouldn't go through segment activation as we will only have a limited
understanding of how the whole stream timeline looks like from the moof. We
only know about the current fragment, while upstream knows about the whole
stream.
This fixes seeking in DASH streams, both for seeks after the current moof and
for seeks into the current moof. The former would fail because the moof ends
and we can't activate any segment, the latter would cause a segment that stops
at the moof end, and no further fragments would be played because we end up
being EOS.
https://bugzilla.gnome.org/show_bug.cgi?id=767071
