qtdemux.c: In function ‘gst_qtdemux_configure_stream’:
qtdemux.c:7764:34: error: suggest parentheses around ‘&&’ within ‘||’ [-Werror=parentheses]
if ((stream->n_samples == 1) && (stream->first_duration == 0)
~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Avoid computing frame rate when a stream contain moof with only one
sample, to avoid an assert. The moof is considered as still picture.
The same is already done for one sample given in the moov.
https://bugzilla.gnome.org/show_bug.cgi?id=782217
... which no longer worked due to unconditionally clearing sample info and
ending up in inconsistent state. Let's tread a bit more carefully and also
allow for the old seek handling that resorts to scanning if no mfra info
is available.
The last entry will most likely get new samples added to it in "robust"
muxing mode, changing the samples_per_chunk and thus making it wrong to
keep the last two entries merged. It will run into an assertion later
when adding a new sample to the chunk.
Thanks to gdiener@cardinalpeak.com for the analysis of the bug and
proposal for a solution.
Timecode trak is only supported for mov right now, not for mp4. That
code would otherwise create an invalid trak if the muxed video contained
timecode metadata.
https://bugzilla.gnome.org/show_bug.cgi?id=782684
We only accept new caps if they are basically the same. We don't want to
reset anything as if the caps are new, otherwise various state could get
out of sync with the current run.
We have some padding added after the initial moov, so a bigger updated
moov can be handled to some degree and is expected. Previously we just
ignored the padding and errored out in cases when the padding would've
just been enough.
This sets up a moov with the correct sample positions beforehand and
only works with constant framerate, I-frame only streams.
Currently only support for ProRes and raw audio is implemented but
adding new codecs is just a matter of defining appropriate maximum frame
sizes.
https://bugzilla.gnome.org/show_bug.cgi?id=781447
When muxing raw audio, we have no way of storing timestamps but are just
storing a continuous stream of audio samples. If the difference between
the expected and the real timestamp becomes to big, we should error out
instead of silently creating files with wrong A/V sync.
https://bugzilla.gnome.org/show_bug.cgi?id=780679
In push mode we process as much as possible in the adapter. When we receive
a DISCONT buffer which we can't match to an actual sample (based on the existing
sample table) and there is still data remaining in the incoming adapter,there is
one of two cases happening:
1) We are doing reverse playback, in which case we should flush out all pending
data
2) We have leftover data from the previous incoming buffer... which we can't do
anything about.
For the second case, make sure we flush out the remaining data so that we can start
parsing again from scratch.
https://bugzilla.gnome.org/show_bug.cgi?id=781319
They should have ideally the same timescale of the video track, which we
can't guarantee here as in theory timecode configuration and video
framerate could be different. However we should set a correct timescale
based on the framerate given in the timecode configuration, and not just
use the framerate numerator.
Make sure offset and neededbytes are properly resetted when all
streams are EOS in push-mode.
Avoids cases when some data might still be pushed by upstream (because
it didn't yet see the resulting GST_FLOW_EOS yet) and qtdemux gets
completely lost.
https://bugzilla.gnome.org/show_bug.cgi?id=781266
buf is the current pad->last_buf value. If ever it gets copied/unreffed,
we need to make sure to write back the new pointer to the last_buf
variable.
Fixes using wrong pointer values in the case of decrasing DTS value
Before pushing a sample, check if there was a change in the current
stsd entry. This patch also assumes that the first stsd entry is
used as default for the first sample. It might cause an uneeded
caps renegotiation when this isn't the case.
stsd can have multiple format entries, parse them all.
This is required to play DVB DASH profile that uses multiple entries
to identify the different available bitrates/options on dash streams
The stream format-specific data is not stored into QtDemuxStreamStsdEntry
Instead of using the stsd as a base pointer, use the actual stsd
entry as the stsd can have multiple entries. This is rarely used
for file playback but is a possible profile with in DVB DASH specs.
This still doesn't support stsd with multiple entries but makes it
easier to do so.
last_buf is the one we're going to write next, not buf. As such we
should check timestamps against that one if there is one to select the
earliest pad.
Also remember the currently selected pad in the very beginning when
storing the first last_buf.
This both solves some edge cases where not the correct next pad was
selected corresponding to the target interleave.
This is an update of d78d589627
We still exit as early as possible in case of non-ok/non-unlinked combined
flow, but we first make sure that we update the internal position variables.
This ensures that if upstreams "ignores" the flow return (and carries on pushing),
we don't end up processing data with completely bogus variables/positions.
