By default imagefreeze will still reject new buffers after the first one
and immediately return GST_FLOW_EOS but the new allow-replace property
allows to change this.
Whenever updating the buffer we now also keep track of the configured
caps of the buffer and from the source pad task negotiate correctly
based on the potentially updated caps.
Only the very first time negotiation of a framerate with downstream is
performed, afterwards only the caps themselves apart from the framerate
are updated.
Elements emitting frames through several srcpads should use a
flow combiner to aggregate the chain returns and therefore only return
GST_FLOW_NOT_LINKED to upstream when all the downstream pads have
received GST_FLOW_NOT_LINKED.
In addition to that, in order to handle pads being relinked downstream,
the flow combiner should be reset in response to RECONFIGURE events.
This ensures that a both srcpads process a chain operation before a
GST_FLOW_NOT_LINKED can be propagated upstream (which would usually stop
the pipeline).
Otherwise, in a configuration with two srcpads, only one linked at a
time, after the relink the element could chain data through the now
unlinked pad and the flow combiner would resolve as GST_FLOW_NOT_LINKED
(stopping the pipeline) just because the now linked pad has not been
chained yet to update the flow combiner.
This patch adds handling of RECONFIGURE events to qtdemux. Also, since
this event handling causes the flow combiner to be used from a thread
other than the qtdemux streaming thread, usages of the flow combiner
has been guarded by the object lock.
The key is to make sure the jitterbuffer is set to NULL *before* the
ptdemux.
The race that existed would basically happen when ptdemux had reached
READY, and the jitterbuffer would then push a buffer, triggering a new
pad with a new payloadtype being added and ghosted to the rtpbin itself.
However, the srcpad of the ptdemux would now be inactive, and all the
sticky-event pushed on it would be swallowed, not allowing any to reach
the ghost-pad. Then the buffer in-flight would come to the ghostpad,
and we would assert that a buffer arrived before the necessary
events.
By simply re-ordering the state-changes, we ensure that there will be
no buffer racing into the ptdemux while its state is being changed,
and the problem disappears completely.
Notice also that there is not point in disconnecting the signals on the
ptdemux before this point, since we need the push-thread to settle
down before we can do this in a non-racy way.
Applications might handle locations and generally configuration of the
sink by themselves instead of having splitmuxsink set the location on
the sink. Nonetheless it makes sense to increment the fragment_id that
is passed to the signal so that applications know which fragment is
requested.
Add parsed=true to output caps, as we always output
whole frames, timestamped and all. Means also that
the output can be decoded by avdec_mjpeg wihout
plugging an extra parser (which has no rank).
Add a property that makes it possible for an application to set the
DateUTC header field in matroska files. This is useful for live feeds,
where the DateUTC header can be set to a UTC timestamp, matching the
beginning of the file.
Needs gstreamer!323
Fixes https://gitlab.freedesktop.org/gstreamer/gst-plugins-good/issues/481
An application might try to access splitmuxsink from sync message handler
by g_object_{get,set} which takes lock also. In general, we don't
take lock around message handler.
By passing `NULL` to `g_signal_new` instead of a marshaller, GLib will
actually internally optimize the signal (if the marshaller is available
in GLib itself) by also setting the valist marshaller. This makes the
signal emission a bit more performant than the regular marshalling,
which still needs to box into `GValue` and call libffi in case of a
generic marshaller.
Note that for custom marshallers, one would use
`g_signal_set_va_marshaller()` with the valist marshaller instead.
The do_expected_timeout() function may release the JBUF_LOCK, so we need
to check if nothing wanted the timer thread to exit after this call.
The side effect was that we may endup going back into waiting for a timer
which will cause arbitrary delay on tear down (or deadlock when test
clock is used).
Fixes#653
JBUF_WAIT_QUEUE drops the JBUF_LOCK, which means the stop condition
for the chain function may have changed (change_state to NULL). Check
this immediately after the wait so that we don't delay shutting down.
When in-place, running an allocation is not useful since videocrop
is not implicated in the allocation. So only force the allocation
query for the case it was in passthrough. This is needed since the
change in the crop region will likely pull us out of this mode. For the
case we where neither in passthrough or in-place, the allocation query
is already ran by the baseclass, so nothing special is needed.
This fixes performance issues when changing the crop region per frame.
This was reproduced using videocrop2-test.
One of the jitterbuffers functions is to try and make sense of weird
network behavior.
It is quite unhelpful for the jitterbuffer to start dropping packets
itself when what you are trying to achieve is better network resilience.
In the case of a skew, this could often mean the sender has restarted
in some fashion, and then dropping the very first buffer of this "new"
stream could often mean missing valuable information, like in the case
of video and I-frames.
This patch simply reverts back to the old behavior, prior to 8d955fc32b
and includes the simplest test I could write to demonstrate the behavior,
where a single packet arrives "perfectly", then a 50ms gap happens,
and then two more packets arrive in perfect order after that.
# Conflicts:
# tests/check/elements/rtpjitterbuffer.c
The memory leak occurs in the case when the buffer has been
added to the fragment_buffers array of the current pad and
never been sent because of the push failure of the previous
buffers: moof or mdat header or fragmented buffer(s).
This commit adds custom element messages for when gstrtpjitterbuffer
drops an incoming rtp packets due to for example arriving too late.
Applications can listen to these messages on the bus which enables
actions to be taken when packets are dropped due to for example high
network jitter.
Two properties has been added, one to enable posting drop messages and
one to set a minimum time between each message to enable throttling the
posting of messages as high drop rates.
There are in the wild (mp4) streams that basically contain no tracks
but do have a redirect info[0], in which case, we won't be able
to expose any pad (there are no tracks) so we can't post anything but
an error on the bus, as:
- it can't send EOS downstream, it has no pad,
- posting an EOS message will be useless as PAUSED state can't be
reached and there is no sink in the pipeline meaning GstBin will
simply ignore it
The approach here is to to add details to the ERROR message with a
`redirect-location` field which elements like playbin handle and use right
away.
[0]: http://movietrailers.apple.com/movies/paramount/terminator-dark-fate/terminator-dark-fate-trailer-2_480p.mov
When the queue is full (and adding more packets would risk a seqnum
roll-over), the best approach is to just start pushing out packets
from the other side. Just pushing out the packets results in the
timers being left hanging with old seqnums, so it's safer to just
execute them immediately in this case. It does limit the timer space
to the time it takes to receiver about 32k packets, but without
extended sequence number, this is the best RTP can do.
This also results in the test no longer needed to have timeouts or
timers as pushing packets in drives everything.
Fixes#619
