We have some padding added after the initial moov, so a bigger updated
moov can be handled to some degree and is expected. Previously we just
ignored the padding and errored out in cases when the padding would've
just been enough.
This sets up a moov with the correct sample positions beforehand and
only works with constant framerate, I-frame only streams.
Currently only support for ProRes and raw audio is implemented but
adding new codecs is just a matter of defining appropriate maximum frame
sizes.
https://bugzilla.gnome.org/show_bug.cgi?id=781447
When muxing raw audio, we have no way of storing timestamps but are just
storing a continuous stream of audio samples. If the difference between
the expected and the real timestamp becomes to big, we should error out
instead of silently creating files with wrong A/V sync.
https://bugzilla.gnome.org/show_bug.cgi?id=780679
In push mode we process as much as possible in the adapter. When we receive
a DISCONT buffer which we can't match to an actual sample (based on the existing
sample table) and there is still data remaining in the incoming adapter,there is
one of two cases happening:
1) We are doing reverse playback, in which case we should flush out all pending
data
2) We have leftover data from the previous incoming buffer... which we can't do
anything about.
For the second case, make sure we flush out the remaining data so that we can start
parsing again from scratch.
https://bugzilla.gnome.org/show_bug.cgi?id=781319
They should have ideally the same timescale of the video track, which we
can't guarantee here as in theory timecode configuration and video
framerate could be different. However we should set a correct timescale
based on the framerate given in the timecode configuration, and not just
use the framerate numerator.
Make sure offset and neededbytes are properly resetted when all
streams are EOS in push-mode.
Avoids cases when some data might still be pushed by upstream (because
it didn't yet see the resulting GST_FLOW_EOS yet) and qtdemux gets
completely lost.
https://bugzilla.gnome.org/show_bug.cgi?id=781266
buf is the current pad->last_buf value. If ever it gets copied/unreffed,
we need to make sure to write back the new pointer to the last_buf
variable.
Fixes using wrong pointer values in the case of decrasing DTS value
Before pushing a sample, check if there was a change in the current
stsd entry. This patch also assumes that the first stsd entry is
used as default for the first sample. It might cause an uneeded
caps renegotiation when this isn't the case.
stsd can have multiple format entries, parse them all.
This is required to play DVB DASH profile that uses multiple entries
to identify the different available bitrates/options on dash streams
The stream format-specific data is not stored into QtDemuxStreamStsdEntry
Instead of using the stsd as a base pointer, use the actual stsd
entry as the stsd can have multiple entries. This is rarely used
for file playback but is a possible profile with in DVB DASH specs.
This still doesn't support stsd with multiple entries but makes it
easier to do so.
last_buf is the one we're going to write next, not buf. As such we
should check timestamps against that one if there is one to select the
earliest pad.
Also remember the currently selected pad in the very beginning when
storing the first last_buf.
This both solves some edge cases where not the correct next pad was
selected corresponding to the target interleave.
This is an update of d78d589627
We still exit as early as possible in case of non-ok/non-unlinked combined
flow, but we first make sure that we update the internal position variables.
This ensures that if upstreams "ignores" the flow return (and carries on pushing),
we don't end up processing data with completely bogus variables/positions.
TFDTs with time 0 are being ignored since commit 1fc3d42f. They're
mistaken with the case of not having TFDT, but those two cases
must be distinguished in some way.
This patch passes an extra boolean flag when the TFDT is present.
This is now the condition being evaluated, instead of checking for
0 time.
https://bugzilla.gnome.org/show_bug.cgi?id=780410
If we have multiple tracks with timecodes, or it's not the first track
that has timecodes, or not the first buffer, we already started a chunk
for media data. We now need to "close" that chunk because we wrote data
for the timecode track and a new chunk has to be started for the
original track the next time it has data.
Similar to what was done in adaptivedemux, ignore seek
events we've already handled - such as when they are received
on every srcpad of files with lots of streams.
Otherwise mdatleft will have a value calculated from the initial
mdatsize minus the parts of the stream that we saw, which is not
including all the parts of the stream that might've been skipped.
Take into account the atoms at the end of the 'trak' atom when
recovering it. So that its size (already computed and added in the trak
size) isn't making offsets wrong.
https://bugzilla.gnome.org/show_bug.cgi?id=771478
We parse the next moof in advance of having pushed
all samples from the previous one in some cases, and
we'll still need the crypto info from the previous
fragment so keep around any unused crypto info entries
when adding new ones
qtdemux.c: In function ‘qtdemux_parse_samples’:
qtdemux.c:8450:39: error: ‘*’ in boolean context, suggest ‘&&’ instead [-Werror=int-in-bool-context]
if (stream->samples_per_frame * stream->bytes_per_frame) {
~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~
This reverts commit 107902ec51.
This commit intended to ensure that keyframe seeks land at the
start timestamp of a keyframe, rather than in the middle of one,
but they cause trouble on files with sparse streams, or with
JPEG 'cover art' tracks that have only one or a few JPEG samples
with very long durations.
That's still desirable for doing seamless cutting of videos,
but needs a rethink for implementation.
https://bugzilla.gnome.org/show_bug.cgi?id=778690
