because _release_pad tries to release it from ctx->sinkpad, which is
multiqueue's sink pad, and currently fails because the probe is not
installed there
This also happens in the very beginning when we receive the first packet, a
warning would be very confusing here. In all places where we should warn about
this, we would've printed a warning already before.
Right above we consider lost_packet packets, each of them having duration,
as lost and triggered their timers immediately. Below we use expected_dts
to schedule retransmission or schedule lost timers for the packets that
come after expected_dts.
As we just triggered lost_packets packets as lost, there's no point in
scheduling new timers for them and we can just skip over all lost packets.
https://bugzilla.gnome.org/show_bug.cgi?id=739868
Resetting the jitterbuffer drops all packets and other things, and will cause
a discontinuity in the packets received by the depayloaders. They should now
also flush anything they had pending as the new data will start at a different
position.
https://bugzilla.gnome.org/show_bug.cgi?id=739868
When doing key uint seek, qtdemux calls gst_qtdemux_adjust_seek
to get proper offset. And then this offset is set to
segment.position and segment.time in gst_qtdemux_perform_seek but
segment.start is not updated.
After that, application sends segment query,
qtdemux sets start and stop to query using gst_segment_to_stream_time. Due
to the wrong value in segment.start, the stop position is smaller than
it should.
https://bugzilla.gnome.org/show_bug.cgi?id=746822
We always write the CTTS in qtmux. Ideally we only want to do that
for streams that need DTS, it should be present on the track information
rather than be decided based on each buffer
As qt uses durations, it doesn't matter, only the difference
between consecutive buffers is important. Also, collectpads
already replaces PTS/DTS with the running times for them.
Instead of checking various state variables around the muxer,
track the current muxing mode in a single 'mux_mode' enum.
Add some implementation notes about the different mux modes
gst_segment_do_seek() does that for us already, and doing it twice
will break non-flushing seeks in interesting ways. Leftover from 1.0
porting.
Also copy over segment offset and applied_rate, just in case.
When multifilesink is operating in any mode other than one file
per buffer, the last file created won't have a file message posted
as multifilesink doesn't handle the EOS event.
This patch fixes it by using the last position to post a file
message when EOS is received. This should ensure at least the
time related data and the filename are posted to the application
or other elements
https://bugzilla.gnome.org/show_bug.cgi?id=747000
When not in fast-start or fragmented mode, we need to be able
to rewrite the size of the mdat atom, or else the output just
won't be playable - the mdat placeholder with size == 0 will
cover the rest of the file, including any moov atom we write out.
https://bugzilla.gnome.org/show_bug.cgi?id=708808
New tags can be found on different parts of the file, so this patch
keeps the stream taglists around for the life cycle of the pad
and adds those new tags as found. Then a new tag is found, the
pad's is marked with a tags changed flag, making the element push
a new tag event on the next check. Before this, we were sending
only the newly found tags, as the element was losing its taglist
when pushing the event.
Global tags are already being read in matroskaparse, but they are not
currently being sent.
This patch makes global tags get sent incrementally whenever new ones
are found.
https://bugzilla.gnome.org/show_bug.cgi?id=746242
When planes property is set to 0, the pipeline executes in
an infinite loop and never exits. Since planes must never
be 0, set the minimum value in the property description
to 1.
https://bugzilla.gnome.org/show_bug.cgi?id=743906
It is expected that buffers are time-stamped with running time. Set
a segment accordingly. In this case we pick 0,-1 as this is what udpsrc
would do. Depayloaders will update the segment to reflect the playback
position.
https://bugzilla.gnome.org/show_bug.cgi?id=635701
The segment start/stop in the query is meant to represent the seekable
portion of the stream. It does not match the segment start/stop. Instead
export 0 to duration.
Previously we were setting new caps with the same content for every H264 or
AAC codec_data we found in the stream, spamming everything and causing
renegotiations.
Instead delay creating the caps until we read the codec_data from the stream,
or fail if we get normal data before the codec_data.
AAC raw caps and H264 avc caps always need codec_data, setting caps on the pad
without them is going to make negotiation fail most of the time. Even if we
later set new caps with the codec_data, that's usually going to be too late.
https://bugzilla.gnome.org/show_bug.cgi?id=746682
Make sure that the sync_src pad has caps before the segment event.
Otherwise we might get a segment event before caps from the receive
RTCP pad, and then later when receiving RTCP packets will set caps.
This will results in a sticky event misordering warning
This fixes warnings in the rtpaux unit test but also in the
rtpaux and rtx examples in tests/examples/rtp
https://bugzilla.gnome.org/show_bug.cgi?id=746445
Before we only started it when either:
- there is no send RTP stream
or
- we received an RTP packet for sending
This could mean that if the send RTP pads are connected but never receive any
RTP data, and the same session is also used for receiving RTP/RTCP, we would
never start the RTCP thread and would never send RTCP for the receiving part
of the session.
This can be reproduced with a pipeline like:
gst-launch-1.0 rtpbin name=rtpbin \
udpsrc port=5000 ! "application/x-rtp, media=video, clock-rate=90000, encoding-name=H264" ! rtpbin.recv_rtp_sink_0 \
udpsrc port=5001 ! rtpbin.recv_rtcp_sink_0 \
rtpbin.send_rtcp_src_0 ! fakesink name=rtcp_fakesink silent=false async=false sync=false \
rtpbin.recv_rtp_src_0_2553225531_96 ! decodebin ! xvimagesink \
fakesrc ! valve drop=true ! rtpbin.send_rtp_sink_0 \
rtpbin.send_rtp_src_0 ! fakesink name=rtp_fakesink silent=false async=false sync=false -v
Before this change the rtcp_fakesink would never send RTCP for the receiving
part of the session (i.e. no receiver reports!), after the change it does.
And before and after this change it would send RTCP for the receiving part of
the session if the sender part was omitted (the last two lines).
