Make the jitterbuffer schedule the timeouts based on the DTS instead
of the PTS. This makes it all smoother with reordered frames and gives
the decoder time to reorder the frames in time.
Only run the skew estimation code when we have a new RTP timestamp. If we have
the same RTP timestamp, we simply use the previous estimation. This works
because the new observation with the same RTP timestamp has to have a bigger
receiver time and is thus not going to influence the estimation except for
causing more jitter.
Fixes https://bugzilla.gnome.org/show_bug.cgi?id=640023
... when operating in non slave mode, and reset if detected.
This should avoid some (large) bogus outgoing timestamp due to jumps
in rtp time, as result of PAUSE/PLAY or seek or ...
* use G_DEFINE_TYPE
* adjust to new GstBuffer and corresponding rtp and rtcp buffer interfaces
* misc caps and segment handling changes
FIXME: also relies on being able to pass caps along with a buffer,
which has no evident equivalent yet, so that either needs one,
or still needs quite some code path modification to drag along caps.
When the jitterbuffer contains -1 timestamps, make sure we still calculate the
buffer fill level by skipping the -1 buffers.
Try to be more resilient to weird input timestamps.
If we detect backward timestamps on the server, don't try to resync when we
don't have an input timestamp (such as when using RTSP over TCP) instead, do
nothing but assume the timestamp was ok, it will correct itself when time goes
forwards.
When deactivating jitterbuffers when the buffering starts, keep the current
percent of the jitterbuffer and also set the jitterbuffer in the buffering state
so that we know when it's filled again.
Add property to get the buffering percentage of the jitterbuffer.
Return the next timestamp in the jitterbuffer.
Use the min-timestamp of the jitterbuffers to calculate an offset so that the
next timestamp is pushed with a timestamp equal to running_time.
Start producing timestamps from 0 in the buffering case too.
Pass the current running time to the jitterbuffer when pausing or resuming so
that it calculate the right offsets.
Small cleanups and comments.
Set the default rtspsrc latency to 2 seconds.
Add signal to pause the jitterbuffer. This will be emitted from gstrtpbin when
one of the jitterbuffers is buffering.
Make rtpbin collect the buffering messages and post a new buffering message with
the min value.
Remove the stats callback from jitterbuffer but pass a percent integer to
functions that affect the buffering state of the jitterbuffer. This allows us
then to post buffering messages from outside of the jitterbuffer lock.
Add callback for buffering stats.
Configure the latency in the jitterbuffer instead of passing it with _insert.
Calculate buffering levels when pushing and popping
Post buffering messages.
When we construct a timestamp that would result in a timestamp that is earlier
than when the packet was received, reset the skew calculation as this is
probably a sign that the sender restarted or paused.
Fixes#593354
No short-desc as we have them in the element details.
Also keep things (Makefile.am and sections.txt) sorted.
Reword ambigous returns. No text after since please.
Original commit message from CVS:
Patch by: Arnout Vandecappelle <arnout at mind dot be>
* gst/rtpmanager/rtpjitterbuffer.c: (rtp_jitter_buffer_reset_skew),
(calculate_skew):
* gst/rtpmanager/rtpjitterbuffer.h:
Keep track of the last outgoing timestamp and of the last sender-side
time. Timestamps can only go forward if they do at the sender
side, can only go back if they do at the sender side, and remain the
same if they remain the same at the sender side. Fixes#565319.
Original commit message from CVS:
* gst/rtpmanager/gstrtpbin.c: (gst_rtp_bin_associate),
(gst_rtp_bin_handle_sync), (create_stream), (free_stream),
(new_ssrc_pad_found):
Remove internal sync pad, use signals instead to get lip-sync
notifications.
* gst/rtpmanager/gstrtpjitterbuffer.c:
(gst_rtp_jitter_buffer_base_init),
(gst_rtp_jitter_buffer_class_init),
(gst_rtp_jitter_buffer_internal_links), (create_rtcp_sink),
(remove_rtcp_sink), (gst_rtp_jitter_buffer_request_new_pad),
(gst_rtp_jitter_buffer_release_pad),
(gst_rtp_jitter_buffer_sink_rtcp_event),
(gst_rtp_jitter_buffer_chain_rtcp),
(gst_rtp_jitter_buffer_get_property):
* gst/rtpmanager/gstrtpjitterbuffer.h:
Make it possible to send SR packets to the jitterbuffer.
Check if the SR timestamps are valid by comparing them to the RTP
timestamps.
Signal the SR packet and the timing information to listeners.
* gst/rtpmanager/gstrtpssrcdemux.c: (create_demux_pad_for_ssrc),
(gst_rtp_ssrc_demux_rtcp_chain), (gst_rtp_ssrc_demux_src_query):
Remove some unused code.
* gst/rtpmanager/rtpjitterbuffer.c: (rtp_jitter_buffer_reset_skew),
(calculate_skew), (rtp_jitter_buffer_get_sync):
* gst/rtpmanager/rtpjitterbuffer.h:
Keep track of the last seen RTP timestamp so that we can filter out
invalid SR packets.
Original commit message from CVS:
* gst/rtpmanager/gstrtpbin.c: (gst_rtp_bin_associate),
(gst_rtp_bin_sync_chain), (create_stream), (new_ssrc_pad_found):
Do not try to keep track of the clock-rate ourselves but simply get the
value from the jitterbuffer.
* gst/rtpmanager/gstrtpjitterbuffer.c:
(gst_jitter_buffer_sink_parse_caps), (gst_rtp_jitter_buffer_chain),
(gst_rtp_jitter_buffer_get_sync):
* gst/rtpmanager/gstrtpjitterbuffer.h:
Add some debug info.
Pass the clock-rate to the jitterbuffer.
Also pass the clock-rate along with the rtp timestamp when getting the
sync parameters.
* gst/rtpmanager/gstrtpptdemux.c: (gst_rtp_pt_demux_chain):
Fix some debug.
* gst/rtpmanager/rtpjitterbuffer.c: (rtp_jitter_buffer_reset_skew),
(calculate_skew), (rtp_jitter_buffer_get_sync):
* gst/rtpmanager/rtpjitterbuffer.h:
Keep track of clock-rate changes and return the clock-rate together with
the rtp timestamps used for sync.
Don't try to construct timestamps when we have no base_time.
* gst/rtpmanager/rtpsource.c: (get_clock_rate):
Request a new clock-rate when the payload type changes.
Reset the jitter calculation when the clock-rate changes.
Original commit message from CVS:
* gst/rtpmanager/gstrtpjitterbuffer.c:
(gst_jitter_buffer_sink_parse_caps),
(gst_rtp_jitter_buffer_flush_stop), (gst_rtp_jitter_buffer_chain):
* gst/rtpmanager/rtpjitterbuffer.c: (rtp_jitter_buffer_reset_skew),
(calculate_skew):
Small cleanups and some more debug info.
Original commit message from CVS:
* gst/rtpmanager/gstrtpjitterbuffer.c:
(gst_jitter_buffer_sink_parse_caps),
(gst_rtp_jitter_buffer_flush_start),
(gst_rtp_jitter_buffer_flush_stop), (gst_rtp_jitter_buffer_chain),
(gst_rtp_jitter_buffer_loop):
Fix problem with using the output seqnum counter to check for input
seqnum discontinuities.
Improve gap detection and recovery, reset and flush the jitterbuffer on
seqnum restart. Fixes#556520.
* gst/rtpmanager/rtpjitterbuffer.c: (rtp_jitter_buffer_insert):
Fix wrong G_LIKELY.
Original commit message from CVS:
* gst/rtpmanager/gstrtpbin.c: (on_sender_timeout),
(create_session), (gst_rtp_bin_associate),
(gst_rtp_bin_sync_chain), (gst_rtp_bin_class_init),
(gst_rtp_bin_request_new_pad):
* gst/rtpmanager/gstrtpbin.h:
Add signal to notify listeners when a sender becomes a receiver.
Tweak lip-sync code, don't store our own copy of the ts-offset of the
jitterbuffer, don't adjust sync if the change is less than 4msec.
Get the RTP timestamp <-> GStreamer timestamp relation directly from
the jitterbuffer instead of our inaccurate version from the source.
* gst/rtpmanager/gstrtpjitterbuffer.c:
(gst_rtp_jitter_buffer_chain), (gst_rtp_jitter_buffer_loop),
(gst_rtp_jitter_buffer_get_sync):
* gst/rtpmanager/gstrtpjitterbuffer.h:
Add G_LIKELY macros, use global defines for max packet reorder and
dropouts.
Reset the jitterbuffer clock skew detection when packets seqnums are
changed unexpectedly.
* gst/rtpmanager/gstrtpsession.c: (on_sender_timeout),
(gst_rtp_session_class_init), (gst_rtp_session_init):
* gst/rtpmanager/gstrtpsession.h:
Add sender timeout signal.
* gst/rtpmanager/rtpjitterbuffer.c: (rtp_jitter_buffer_reset_skew),
(calculate_skew), (rtp_jitter_buffer_insert),
(rtp_jitter_buffer_get_sync):
* gst/rtpmanager/rtpjitterbuffer.h:
Add some G_LIKELY macros.
Keep track of the extended RTP timestamp so that we can report the RTP
timestamp <-> GStreamer timestamp relation for lip-sync.
Remove server timestamp gap detection code, the server can sometimes
make a huge gap in timestamps (talk spurts,...) see #549774.
Detect timetamp weirdness instead by observing the sender/receiver
timestamp relation and resync if it changes more than 1 second.
Add method to report about the current rtp <-> gst timestamp relation
which is needed for lip-sync.
* gst/rtpmanager/rtpsession.c: (rtp_session_class_init),
(on_sender_timeout), (check_collision), (rtp_session_process_sr),
(session_cleanup):
* gst/rtpmanager/rtpsession.h:
Add sender timeout signal.
Remove inaccurate rtp <-> gst timestamp relation code, the
jitterbuffer can now do an accurate reporting about this.
* gst/rtpmanager/rtpsource.c: (rtp_source_init),
(rtp_source_update_caps), (calculate_jitter),
(rtp_source_process_rtp):
* gst/rtpmanager/rtpsource.h:
Remove inaccurate rtp <-> gst timestamp relation code.
* gst/rtpmanager/rtpstats.h:
Define global max-reorder and max-dropout constants for use in various
subsystems.
Original commit message from CVS:
Based on patch by: Olivier Crete <tester at tester dot ca>
* gst/rtpmanager/gstrtpjitterbuffer.c:
(gst_rtp_jitter_buffer_chain), (gst_rtp_jitter_buffer_loop):
Make the buffer metadata writable before inserting it in the
jitterbuffer because the jitterbuffer will modify the timestamps.
* gst/rtpmanager/rtpjitterbuffer.c:
Update method comment about requiring writable metadata on buffers.
* gst/rtpmanager/rtpsession.c: (rtp_session_process_sr),
(rtp_session_process_rtcp):
Make the RTCP buffer metadata writable because we want to modify the
metadata.
Fixes#546312.
Original commit message from CVS:
* gst/rtpmanager/gstrtpjitterbuffer.c:
(gst_rtp_jitter_buffer_chain), (gst_rtp_jitter_buffer_loop):
When checking the seqnum, reset the jitterbuffer if the gap is too big,
we need to do this so that we can better handle a restarted source.
Fix some comments.
* gst/rtpmanager/rtpjitterbuffer.c: (calculate_skew),
(rtp_jitter_buffer_insert):
Tweak the skew resync diff.
Use our working seqnum compare function in -base.
Rework the jitterbuffer insert code to make it clearer and more
performant by only retrieving the seqnum of the input buffer once and by
adding some G_LIKELY compiler hints.
Improve debugging for duplicate packets.
* gst/rtpmanager/rtpsource.c: (rtp_source_process_rtp):
Fix a comment, we don't do skew correction here..
Original commit message from CVS:
Patch by: Stefan Kost <ensonic@users.sf.net>
* gst/rtpmanager/rtpjitterbuffer.c: (calculate_skew):
Don't try to reset the clock skew when we have no timestamps.
Fixes#519005.
Original commit message from CVS:
Patch by: Olivier Crete <tester@tester.ca>
* gst/rtpmanager/gstrtpjitterbuffer.c:
(gst_jitter_buffer_sink_parse_caps), (gst_rtp_jitter_buffer_chain):
* gst/rtpmanager/rtpjitterbuffer.c: (calculate_skew),
(rtp_jitter_buffer_insert):
* gst/rtpmanager/rtpjitterbuffer.h:
Remove the fixed clock-rate from the jitterbuffer and extend it so that
a clock-rate can be provided with each buffer instead. Fixes#511686.
