Updated gst_segment_position_from_stream_time and gst_segment_to_stream_time to reflect correct calculations for the case when the applied rate is negative.
Pasting from design docs:
===============================
Stream time is calculated using the buffer times and the preceding SEGMENT
event as follows:
stream_time = (B.timestamp - S.start) * ABS (S.applied_rate) + S.time
For negative rates, B.timestamp will go backwards from S.stop to S.start,
making the stream time go backwards.
===============================
Therefore, the calculation for applied_rate < 0 should be:
stream_time = (S.stop - B.timestamp) * ABS (S.applied_rate) + S.time
and the reverse:
B.timestamp = S.stop - (stream_time - S.time) / ABS (S.applied_rate)
https://bugzilla.gnome.org/show_bug.cgi?id=756810
gst_segment_to_position might cause confusion, especially with the addition of
gst_segment_position_from_stream_time . Deprecated gst_segment_to_position
now, and replaced it with gst_segment_position_from_running_time.
Also added unit tests.
gst_segment_position_from_stream_time() will convert stream time into a
position in the segment so that gst_segment_to_stream_time() with that
position returns the same stream time. It will return -1 if the stream time
given is not inside the segment.
Do not do any checks for the start/stop in the new
gst_segment_to_running_time_full() method, we can let this be done by
the more capable gst_segment_clip() method. This allows us to remove the
enum of results and only return the sign of the calculated running-time.
We need to put the old clipping checks in the old
gst_segment_to_running_time() still because they work slightly
differently than the _clip methods.
See https://bugzilla.gnome.org/show_bug.cgi?id=740575
Add a clip argument to gst_segment_to_running_time_full() to disable
the checks against the segment boundaries. This makes it possible to
generate an extrapolated running-time for timestamps outside of the
segment.
See https://bugzilla.gnome.org/show_bug.cgi?id=740575
Add a helper method to get a running-time with a little more features
such as detecting if the value was before or after the segment and
negative running-time.
API: gst_segment_to_running_time_full()
Fixes https://bugzilla.gnome.org/show_bug.cgi?id=740575
The position in the segment is relative to the start but the offset
isn't, so subtract the start from the position when setting the offset.
Add unit test for this as well.
Add GST_SEEK_FLAG_TRICKMODE_KEY_UNITS and
GST_SEEK_FLAG_TRICKMODE_NO_AUDIO, and rename GST_SEEK_FLAG_SKIP
to GST_SEEK_FLAG_TRICKMODE (with backwards compat define).
Do the same for the corresponding SEGMENT flags.
https://bugzilla.gnome.org/show_bug.cgi?id=735666
They are very confusing for people, and more often than not
also just not very accurate. Seeing 'last reviewed: 2005' in
your docs is not very confidence-inspiring. Let's just remove
those comments.
Very often, when the end of a segment is detected by demuxer, the position
is slightly outside the segment boundaries. Currently, if that is the case
the base will be set to NONE instead of normal accumulation. This would
break non-flushing seeks in oggdemux and most likely other demuxers.
Fixes https://bugzilla.gnome.org/show_bug.cgi?id=696899
Add an offset field that is used to track at what position the segment was
updated. This is used to set the running time to 0 when we do a flushing
seek that doesn't update the position.
See https://bugzilla.gnome.org/show_bug.cgi?id=680306
Define a 0 and -1 step amount. They used to almost do the same thing but now, 0
cancels/stops the current step and -1 keeps on stepping until the end of the
segment.
See https://bugzilla.gnome.org/show_bug.cgi?id=679378
Make GstSeekFlag to GstSegmentFlag conversion explicit, and
set only those seek flags in the segment flags which are
mapped. This makes sure we don't have extraneous flags
littering our segment flag field, which also fixes the
debug printing/serialisation of segment events in the
debug log.
Don't use the duration in the segment for calculating clipping values.
The duration is expressed in stream time and clipping is done on unrelated
timestamp values.
This used to be interesting for elements that used the segment structure to
implement seeking because then they would use stream-time for the segment
start/stop values and the duration could be used as a fallback when the stop
position was not set. Now that the complete segment event is passed between
elements we cannot do this anymore because some elements might store the
duration and start/stop values with different time bases in the segment.
Improve GstSegment, rename some fields. The idea is to have the GstSegment
structure represent the timing structure of the buffers as they are generated by
the source or demuxer element.
gst_segment_set_seek() -> gst_segment_do_seek()
Rename the NEWSEGMENT event to SEGMENT.
Make parsing of the SEGMENT event into a GstSegment structure.
Pass a GstSegment structure when making a new SEGMENT event. This allows us to
pass the timing info directly to the next element. No accumulation is needed in
the receiving element, all the info is inside the element.
Remove gst_segment_set_newsegment(): This function as used to accumulate
segments received from upstream, which is now not needed anymore because the
segment event contains the complete timing information.
