The correct way to determine the byte offset at a certain yoffset
in a subsampled component is to shift the yoffset by the component's
hsub
This fixes out-of-bounds memory accesses and visible artefacts,
example pipeline with the samples from #802:
gst-launch-1.0 compositor name=vmixer sink_1::xpos=1910 sink_1::ypos=1080 ! \
videoconvert ! videorate ! xvimagesink \
filesrc location=VID_20200723_203606.mp4 ! decodebin name=demux1 ! \
queue ! videoflip method=vertical-flip ! vmixer. \
filesrc location=bridgeoverstubbledwater.mp4 ! decodebin name=demux2 ! \
queue ! vmixer.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gst-plugins-base/-/merge_requests/988>
This was only taken care of previously if there was a decoder before.
However if previously a decoder was not needed then the ghostpad
would've been linked directly to the slot's srcpad.
Reconfiguring the slot requires this to be undone so that linking can
happen normally.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gst-plugins-base/-/merge_requests/985>
Add a way for applications to specify that the underlying file is
growing which implies that the source won't EOS when reaching the end
of the file but instead start monitoring it and start reading it again
whenever a change is detected.
Also add a validate test to check the behavior
Part-of: <https://gitlab.freedesktop.org/gstreamer/gst-plugins-base/-/merge_requests/937>
Instead of going through the list of known muxers go ahead and
instantiate the muxer specified as 'preset name' as this specifies
the exact element factory name to use.
When that property is left to its default, the width and height
property considers frames from input pads with width or height <= 0
should be left unscaled in that dimension.
Setting this property to FALSE changes that behaviour to < 0, as when
animating these properties, 0 should be a valid end value (eg. shrinking
an input stream until it disappears).
The default value of the width and height properties is set to -1, so that
the default behaviour stays consistent whether that new property is set
or not.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gst-plugins-base/-/merge_requests/923>
In the case `videoaggregator` is set as allowing format conversions,
and as we convert only on the sinkpads, we should ensure that the
chosen format is usable by the subclass. This in turns implies
that the format is usable on the srcpad.
When doing conversion *any* format can be used on the sinkpads, and this
is the only way that we can avoid race conditions during renegotiations
so we can not change that fact, we just need to ensure that the chosen
intermediary format is usable, which was not actually ensured before
that patch.
Fixes https://gitlab.freedesktop.org/gstreamer/gst-plugins-base/-/issues/834
Part-of: <https://gitlab.freedesktop.org/gstreamer/gst-plugins-base/-/merge_requests/909>
Increases the throughput of compositing by using more CPU cycles across
multiple threads. Simple cases (the output contains one pixel from at
most one input) can have up to a 70% increase in throughput. Not so
simple cases are limited by the region with the most number of
composite operations.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gst-plugins-base/-/merge_requests/755>
The type is called GstVideoTransferFunction so the function names should
match, otherwise gobject-introspection is keeping the functions as
global functions instead of methods on the type.
The same mistake was also made in lots of other APIs over the years, but
here we can at least fix it for 1.18 still.
Thanks to Marijn Suijten for noticing.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gst-plugins-base/-/merge_requests/807>
When a pad has alpha != 1.0 it means that the resulting frames will
contain alpha and thus can't fully obscure with a lower zorder.
Also simplifies the other checks as blending with an OVER or on a
transparent is not a no-op as previously assumed.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gst-plugins-base/-/merge_requests/764>
It was not working properly and the implementation of the smartencoder
element was weird. This introduce a number of changes (which are all
in one single commit because they basically all work together and lead
to basically reimplementing the element):
* Make smartencoder a bin so that the reencoding chain of elements are
inside of it instead of not having any parent. Those elements were not
be visible when dumping the pipeline which was very confusing.
* Make encodebin create the right encoder with a capsfilter (and parser)
to properly enforce the format specified by the user, and so that the
encoder properties specified in the encoding profile are respected.
* Use `decodebin` to do the decoding instead of selecting a decoder
ourself and not plug any parser etc...
* Ensure that negotiated format in the sinkpad of smart encoder is fixed
through time when the user requested a non dynamic output
* Add a parser at the beginning of the smart encoder
* Handle errors when reencoding
Part-of: <https://gitlab.freedesktop.org/gstreamer/gst-plugins-base/-/merge_requests/751>
When using tile format, the stride has a different meaning. It used
the MSB and LSB 16bits to encode respectively the width and height in
number of tiles.
This issue was introduce with commit e5b70d384c which was fixing
missing size recalculation when strides and offset is updated.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gst-plugins-base/-/merge_requests/753>
