release_frame() can be useful for manually dropping frames without posting QoS messages like finish_frame() would.
Matches the same kind of API on the decoder side of things.
Modifies the behaviour of release_frame() to make sure events from released frames are stored as 'pending'
and pushed before the next non-dropped frame. This is needed because now release_frame() can be called outside of
finish_frame(), so we would potentially just lose events and bad things would happen.
drop_frame() was also added to match the decoder API. It functions almost identically to finish_frame() without a buffer
attached to the frame, except instead of immediately pushing the frame's events, it will store them as pending.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/7190>
In case when conn->input_stream is NULL and glib was built with
"glib_checks" enabled, g_pollable_input_stream_read_nonblocking()
returns -1, but does not set the "err".
The call stack:
read_bytes() ->
fill_bytes() ->
fill_raw_bytes()
The return value -1 passed up to read_bytes() and incorrectly
processed there after "error:" label.
This changes the return value to EINVAL.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/7210>
Fix an inverted condition when checking if sink pad caps match
the codec-preference of an unassociated transceiver, and
fix a condition check for transceiver media kind to
avoid matching sinkpad requests where caps aren't provided
against unassociated transceivers where the caps might
not match later.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/7237>
According to the ffmpeg documentation[1] the read_packet function should never
return 0. ffmpegdata_peek returns 0 when the stream is EOF causing us to fail
detecting EOF and never close the pipeline, continually spinning on more data.
ffmpeg instead wants an AVERROR_EOF code for to signal EOF.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/4999>
With MR 7156, transceivers and transports are created earlier,
but for sendrecv media we could get `not-linked` errors due to
transportreceivebin not being connected to rtpbin yet when incoming
data arrives.
This condition wasn't being tested in elements_webrtcbin, but could be
reproduced in the webrtcbidirectional example. This commit now also
adds a test for this, so that this doesn't regress anymore.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/7294>
A previous fix, a275e1e029, is correct but was too
permissive since it treats all un-matched NAL units the same as AU delimiters
even though some other NAL unit types can be encountered in the processing loop.
The problem this can cause is that some hardware decoders experience bad
performance when handling FD units that precede the SPS.
This change restores the original behavior for FDs so that they're ignored until
the SPS is received and it preserves the codec conformance test gains that the
fix has achieved.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/7166>
glCheckFrameStatus() can fail by returning 0, and otherwise return a
status. Fix the trace to make it clear when we get an unkown status
compare to having an error, in which case we also trace the error code.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/7291>
Parts may emit bus messages that want to take the splitmuxsrc
lock and prevent the downward state change. Avoid a deadlock
after a part sends an error message by taking a ref and
dropping the lock around the unprepare call
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/7053>
Publish fragment-id in the messages that splitmuxsink and splitmuxsrc
send, so when they are received out of order (due to async finalization,
for example), they can still be identified / ordered correctly.
Fix a race in the splitmuxsink unit test where messages might be
received out of order
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/7053>
Add a `num-lookahead` property that will 'prepare' a number of
fragments in advance of the playhead if they have been deactivated
or closed by a limited number of `num-open-fragments`. It can help
to avoid any play stalls reading the indexes or headers of the next
file from high-latency media or on resource limited machines.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/7053>
Publish the playback offset for and duration into the
splitmuxsink-fragment-closed bus message as each fragment
finishes.
These can be passed to splitmuxsrc via the 'add-fragment'
signal to avoid splitmuxsrc measuring all files on startup
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/7053>
Add a reasonably large default for the number of simulataneous
files to open, that won't affect users that split recordings into
a few large files, but will help prevent fd exhaustion for users
that make recordings with lots of small fragments
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/7053>
When calculating the timestamp offset to apply to
media streams in a fragment, ensure that all fragments
are offset "together" to preserve alignment in cases
where there might gaps in a recording at a fragment boundary.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/7053>
Add a signal that allows adding fragments with a specific offset
and duration directly to splitmuxsrc's list. By providing the
fragment's offset on the playback timeline and duration directly,
splitmuxsrc doesn't need to measure the fragment making for faster
startup times.
Add a bus message that's published when fragments are measured,
reporting the offset and duration, so they can be cached by an
application and used on future invocations.
Add examples for handling the bus message and using the 'add-fragment'
signal.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/7053>
Add a property to limit the number of parts splitmux will open
simultaneously. Modify the part handling to support deactivating
and reactivating the demuxing for each part.
The default is '0', to preserve the existing behaviour of opening
all parts at the beginning.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/7053>
According to https://w3c.github.io/webrtc-pc/#set-the-session-description
(steps in 4.6.10.), we should be creating and associating transceivers when
setting session descriptions.
Before this commit, webrtcbin deviated from the spec:
1. Transceivers from sink pads where created when the sink pad was
requested, but not associated after setting local description, only
when signaling is STABLE.
2. Transceivers from remote offers were not created after applying the
the remote description, only when the answer is created, and were then
only associated once signaling is STABLE.
This commit makes webrtcbin follow the spec more closely with regards to
timing of transceivers creation and association.
A unit test is added, checking that the transceivers are created and
associated after every session description is set.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/7156>
If a downstream buffer pool is offered, vulkanupload checks its allocation
parameters to honor them. Only adds to usage the TRANSFER bits, which are
required to upload buffers.
Also, fail if the buffer pool cannot be configured with the current parameters.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/7219>
If the stream has a special colorimetry that is not in the colorimetry
list, it will cause negotiation to fail. We should allow passing any
colorimetry, so add an extra structure without the colorimetry field.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/7029>
video-info supports encoded format to have RGB color-matrix, while
v4l2object just leave the v4l2 matrix to default when mapping
GST_VIDEO_COLOR_MATRIX_RGB. It causes gst matrix changed to be
GST_VIDEO_COLOR_MATRIX_BT601 when mapping v4l2 colorimetry.
So add support for encoded format with RGB color-matrix in v4l2object.
Note that for M2M encoders, we should in theory assume that that we can
transfer this value from OUTPUT to CAPTURE queues, though its only true
if the drivers does not do CSC. For now, we don't support any RGB
codecs, but leaving a note for the future.
Part-of: <https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/3952>
