packet_length is defined as a guint16 in the PESHeader structure. This
definition match the specification. But since we add 6 bytes to the
packet_length value (length of start_code + stream_id + packet_length),
we can overflow the guint16 when the value in the PES header is greater
than 65529.
So use a guint32 instead of a guint16 to avoid overflow.
https://bugzilla.gnome.org/show_bug.cgi?id=736490
32 bit integers are going to overflow, especially the PCR offset to
the first PCR will overflow after about 159 seconds. This makes playback
of streams stop at 159 seconds as suddenly the timestamps are starting
again from 0. Now we have a few more years time until it happens again
and 64 bits are too small.
It was previously a mix and match of both variants, introducing just too much
confusion.
The prefix are from now on:
* GstMpegts for structures and type names (and not GstMpegTs)
* gst_mpegts_ for functions (and not gst_mpeg_ts_)
* GST_MPEGTS_ for enums/flags (and not GST_MPEG_TS_)
* GST_TYPE_MPEGTS_ for types (and not GST_TYPE_MPEG_TS_)
The rationale for chosing that is:
* the namespace is shorter/direct (it's mpegts, not mpeg_ts nor mpeg-ts)
* the namespace is one word under Gst
* it's shorter (yah)
When wrapover/reset occur, we end up with a small window of time where
the PTS/DTS will still be using the previous/next time-range.
In order not to return bogus values, return GST_CLOCK_TIME_NONE if the
PTS/DTS value to convert differs by more than 15s against the last seen
PCR
https://bugzilla.gnome.org/show_bug.cgi?id=674536
Using 32bit unsigned values for corrected pcr/offset meant that we
potentially ended up in bogus values
Furthermore, refpcr - refpcroffset could end up being negative, which
PCRTIME_TO_GSTTIME() can't handle (and returned a massive positive value)
Co-Authored by: Thibault Saunier <tsaunier@gnome.org>
From a high level perspective, the new process for seeking h264
streams is as follows:
1) Rewind the stream until we find the first I-slice of a frame,
and mark its offset in the stream.
2) Rewind the stream until we find SPS and PPS informations,
to make sure the subsequent parser is up to date.
3) Accumulate optionnal SEI NAL units on the way.
4) Push the SPS, PPS and SEI units before the new keyframe.
https://bugzilla.gnome.org/show_bug.cgi?id=675132
If _set_current_pcr_offset gets called after a flushing seek, we ended
up using the current group for delta calculation ... whereas we should
be using the first group to calculate shifts.
Also add an early exit if there are no changes to apply
When working in push mode, we need to be able to evaluate the duration
based on a single group of observations.
To do that we use the current group values
When handling the PTS/DTS conversion in new groups, there's a possibility
that the PTS might be smaller than the first PCR value observed, due to
re-ordering.
When using the current group, only apply the wraparound correction when we
are certain it is one (i.e. differs by more than a second) and not when it's
just a small difference (like out-of-order PTS).
https://bugzilla.gnome.org/show_bug.cgi?id=731088
When we receive sticky events from upstream, always return TRUE.
Fixes the issue where we receive custom sticky events (such as "uri")
and no pads are created yet.
Since all the other timestamp tracking now gets reset on a discont,
it makes sense to wait for a PCR and timestamp buffers like when
playback first starts
Due to mpegts streaming nature some pads are created but are only added
later to the element. This can cause a scenario where the first stream
doesn't have an available decoder (while the next ones still pending
would have) and tsdemux will fail with not-linked as the first stream
added wouldn't be linked.
To avoid this tsdemux needs to add pads to the flowcombiner
when they are created instead of only when adding them to the
element.
* Search in current pending values first. For CBR streams we can very
easily end up having just one initial observations and then nothing
else (since the bitrate doesn't change).
* Use one group whether we are in that group *OR* if there is only
one group.
* If the group to use isn't closed (points are being accumulated in the
PCROffsetCurrent), use the latest data available for calculation
* If in the unlikelyness that all of this *still* didn't produce more
than one data point, just return the initial offset
While the calculation done in these macros will work with 64bit
integers, they will fail if working with 32bit integers.
Force the scaling up to solve that.
This amazingly didn't introduce major issues up to now, but resulted
in bogus values in debug logs.
Doing a hard flush on the packetizer will drop all observations, which
will eventually break push-based seeking (with BYTES segment) since
we won't know where to seek to anymore (new data would always be
considered as the beginning of the stream).
While this probably should never happen if callers are well behaved,
this avoids a crash if it does. With a warning about it. Unsure if
it'd be better to not add at all, but it should not happen...
Coverity 1139713
gst_ts_demux_push_pending_data() will check if it now can activate the
stream and add the pad, we don't have to check that ourselves.
Fixes playback of very short MPEG TS files.
Apart from just adding detection of the proper stream type, we also need to only
output the first substream (0x71) which contains the core substream.
While this does not provide *full* DTS-HD support (since it will miss the complementary
substreams), it will still work in the way legacy (non-DTS-HD) bluray players would work.
https://bugzilla.gnome.org/show_bug.cgi?id=725563
Keep a list of current global tags around and push them
whenever a new stream is started. Also convert all stream
specific tags to global as they are stream specific for
the container, so they are global for the streams from
within that container.
https://bugzilla.gnome.org/show_bug.cgi?id=644395
