type is truncated to 0-31 with "& 0x1f", but right after that it is checks if
the value is equivalent to GST_H265_NAL_VPS, GST_H265_NAL_SPS, and
GST_H265_NAL_PPS (which are 32, 33, and 34 respectively). Obviously, this will
never be True if the value is maximum 31 after the truncation.
The intention of the code was to truncate to 0-63.
After further investigation the previous commit is wrong. The code intended to
check if the type is 39 or the ranges 41-44 and 48-55. Just like gsth265parse.c
does. Type 40 would not be complete.
nal_type is the index for a GstH265NalUnitType enum. There are two types of dead
code here:
First, after checking if nal_type is >= 39 there are two OR conditionals that
check if the value is in ranges higher than that number, so if nal_type >= 39
falls in the True branch those other conditions aren't checked and if it falls
in the False branch and they are checked, they will always also be False. They
are redundant.
Second, the enum has a range of 0 to 40. So the checks for ranges higher than 41
should never be True.
Removing this redundant checks.
CID 1249684
The running average was wrong and the resulting scaling factor was only held in
place using the CLAMP. In addtion we are now convering quickly to volume
changes.
FInally now with this change, we can change the resolution defines and
everythign adjusts.
Commit bd27a1f30b added a few error handling
memory management checks. These check srccaps to see if it needs to be
unreferenced before returning, in the case of invalid_caps this goto jump
always happens before srccaps is set, so it will always be NULL in this
error label.
CID #1352035
For APP/JPG markers the size is following and we have to skip that. This is
not really a problem unless the marker contains e.g. a preview JPEG or
something else that we might interprete as another marker.
qtdemux calculates framerate using duration and the number of sample.
In case of fragmented mp4 format, however, the number of sample can
be figure out after parsing every moof box. Because qtdemux does not
parse every moof in QTDEMUX_STATE_HEADER state, it will cause incorrect
framerate calculation.
This patch will triger gst_qtdemux_configure_stream() for every new moof.
Then, framerate will be calculated by using duration and n_samples of the moof.
https://bugzilla.gnome.org/show_bug.cgi?id=760774
Based on document ISO_IEC_14496-12, edit list box can have
segment duration as zero. It does not imply that media_start equals to
media_stop. But, it just indicates a sample which should be presented
at the first. This patch derives segment duration using media_time
and duration of file. And set derived duration to segment-duration.
https://bugzilla.gnome.org/show_bug.cgi?id=760781
In case of push mode, qtdemux expose streams after got moov box.
We can not guarantee that a moov box has sample data such as sample duration
and the number of sample in stbl box for fragmented format case.
So, if a moov has no sample data, streams will not be exposed until get the first moof.
https://bugzilla.gnome.org/show_bug.cgi?id=760779
If the following conditions are met:
1) upstream and downstream caps are compatible
2) upstream is interlaced
3) downstream doesn't support progressive mode
then deinterlace will just do passthrough instead of failing to link.
This is done with the following scenario in mind:
videotestsrc ! "video/x-raw,interlace-mode=interleaved" ! deinterlace
name=dein_src ! tee name=t ! queue ! deinterlace name=dein_file ! filesink t. !
queue ! deinterlace name=dein_desktop ! autovideosink
In this case, dein_src will do the deinterlacing. However,
videotestsrc ! "video/x-raw,interlace-mode=interleaved" ! deinterlace
name=dein_src ! tee name=t ! queue ! deinterlace name=dein_file ! filesink t. !
queue ! deinterlace name=dein_desktop ! autovideosink t. ! queue !
"video/x-raw,interlace-mode=interleaved" ! fakesink
In this case, caps auto-negotiation will make dein_file and dein_desktop do
the deinterlacing, while dein_src will be passthrough.
https://bugzilla.gnome.org/show_bug.cgi?id=760995
In this mode we will passthrough all progressive caps but interlaced caps must be
caps where we actually support deinterlacing.
This is the only difference between auto and auto-strict, auto would
passthrough all unsupported interlaced caps.
https://bugzilla.gnome.org/show_bug.cgi?id=720388
Previously the result of the CAPS query and ACCEPT_CAPS depended on what kind
of caps were last set, and e.g. if we last had interlaced caps or not. That's
just broken.
Also previously the handling of non-sysmem caps features was rather random and
unusuable.
Now the behaviour is the following, depending on the mode property:
1) mode=disabled
Completely do passthrough of everything
2) mode=interlaced
Only accept formats we can actually deinterlace, and accept interlaced
and progressive content and always run the deinterlacer and output
progressive content
3) mode=auto (i.e. playbin)
Accept all progressive formats as passthrough, accept all formats that we
can deinterlace ourselves (which we do then), but also accept everything
else for which we then just passthrough. In auto mode, deinterlacing is best
effort: If we can, we deinterlace, if we can't we just output interlaced
content.
https://bugzilla.gnome.org/show_bug.cgi?id=720388https://bugzilla.gnome.org/show_bug.cgi?id=760553
In file included from gstrtpL16depay.h:27:0,
from gstrtp.c:73:
gstrtpchannels.h:154:33: error: 'channel_orders' defined but not used [-Werror=unused-const-variable]
static const GstRTPChannelOrder channel_orders[] =
Especially in push mode we would completely ignore the size of the data chunk
when not stop position is given for the seek. Instead make sure that the end
offset is at most the end of the data chunk if known.
Without this we would output anything after the data chunk, possibly causing
loud noises if the media file is followed by an INFO chunk or an ID3 tag.
We use that to signal "infinity", taking the difference between that and some
other value is not going to give us any useful result for the end offsets of
segments.
Even if we have more data queued up when flushing than the size of the data
chunk, don't process and output it. If the data size is known, this likely
contains another chunk (e.g. an INFO chunk) or things like ID3 tags. Just
outputting them as if they were data is going to cause unexpected behaviour
and unpleasant audio noises.
The current example does not work, it fails with:
ERROR: from element /GstPipeline:pipeline0/GstDecodeBin:decodebin0/GstWavParse:wavparse0: Internal data flow error.
gstwavparse.c(2178): gst_wavparse_loop (): /GstPipeline:pipeline0/GstDecodeBin:decodebin0/GstWavParse:wavparse0:
streaming task paused, reason not-negotiated (-4)
This is because negotiation with wavenc gets messed up by the missing
channel positions configuration.
The proper way to define the channel layout when using the interleave
element in code would be to set the channel-positions property, but
gst-launch-1.0 does not know how to deal with arrays; so the example
pipeline works around the issue by setting the channel-masks in the sink
pads.
Also fix a repetition in the deinterleave example description
https://bugzilla.gnome.org/show_bug.cgi?id=735673
SBC frame length calculation wasn't being rounded up to the nearest byte
(as specified in the A2DP 1.0 specification, section 12.9). This could
cause 'stereo' and 'joint stereo' mode SBC streams to have incorrectly
calculated frame lengths.
Incorrect frame length calculation causes frame coalescing to fail, as
subsequent frames in the stream aren't found in the expected locations.
https://bugzilla.gnome.org/show_bug.cgi?id=742446
The downstream caps query with a filter alraedy gives us the possible
intersection so there is no need to check it again with downstream
if it is supported. Just try to set it directly.
For someone that read the spec is clear the only *invalid*
data block type is 127. For the rest, its useful information.
Additionally. values 7-126 are currently reserved by the
spec so the situation might change in the future.
We are only interested on the first bit of the first
byte of the metadata block header to figure out whether
is marked as the last one. The shift makes it quite
clearer.
If we get anything from 7 to 126 as type when parsing
a metadata block header, we are likely dealing with a
FLAC stream version we don't fully understand. Issue
a warning if so.
Document function assumptions regarding the passed-on
type while at this.
As CRCs are calculated for the comparition already, we
might as well (cheaply) inform the user how the numbers
differ if a missmatched pair is found.
While at it:
Rephrase candidate-frame message to make more sense
Prevents downstream from receiving flushes for a seek only in
upstream. Those seeks are only to start reading from the right
offset when skipping or returning to qt atoms.
https://bugzilla.gnome.org/show_bug.cgi?id=758928
Avoid writing a negative number as a large positive
integer in an edit list when the first_ts is smaller
than the first_dts - which can happen when the first
packet received has a PTS but no DTS.
https://bugzilla.gnome.org/show_bug.cgi?id=759615
Don't increment running time from every buffer. The correct
logic to only increment when running time advances is a
little further down, so delete this left-over line.
Leverage response from gst_rtsp_connection_connect_with_response to
determine if the connection should be retried using authentication. If
so, add the appropriate authentication headers based upon the response
and retry the connection.
https://bugzilla.gnome.org/show_bug.cgi?id=749596
The string could exist but with a wrong format, in that case we still want
to reset the values of client_port_range.min and max like we do if there is
no string.
CID 1139593
We would queue 5 consective packets before considering a reset and a proper
discont here. Instead of expecting the next output packet to have the current
seqnum (i.e. the fifth), expect it to have the first seqnum. Otherwise we're
going to drop all queued up packets.
When working in push-mode, we attempt to push out everything currently
buffered in the adapter.
This has two pitfalls:
* We could stop earlier (the moment we get a non-ok or non-not-linked)
* We return the last combined flow return, which might be completely
different from the previous combined flow return
There might be multiple LOAS config in a row in a full frame. The first
one might be a multi-layer config (which we can't properly parse yet)...
but then followed by a valid (single-layer) one.
The code was previously skipping whole frames (instead of just the LOAS
config we failed to read) resulting in multiple frames (seen up to 6s in
some situation) being dropped before finally getting the configuration.
https://bugzilla.gnome.org/show_bug.cgi?id=758826
auds.blockalign is set once the first caps arrive. If
gst_avi_mux_stop_file() is called before this happens then auds.blockalign
is zero and gst_avi_mux_audsink_set_fields() cause a crash:
[...]
avipad->parent.hdr.rate = avipad->auds.av_bps / avipad->auds.blockalign;
[...]
https://bugzilla.gnome.org/show_bug.cgi?id=758912
It's not enough to have timeout or event based SPS/PPS information sent
in RTP packets. There are some scenarios when key frames may appear
more frequently than once a second, in which case the minimum timeout
for "config-interval" of 1 second for sending SPS/PPS is not sufficient.
It might also be desirable in general to make sure the SPS/PPS is
available with every keyframe (packet loss aside), so receivers can
actually pick up decoding immediately from the first keyframe if
SPS/PPS is not signaled out of band.
This patch adds the possibility to send SPS/PPS with every key frame. This
mode can be enabled by setting "config-interval" property to -1. In this
case the payloader will add SPS and PPS before every key (IDR) frame.
https://bugzilla.gnome.org/show_bug.cgi?id=757892
This way we can use -1 as special value, which is nicer than MAXUINT.
This is backwards compatible even with the GValue API, as shown by
a unit test.
https://bugzilla.gnome.org/show_bug.cgi?id=757892
generate_rtcp can produce empty packets when reduced size RTCP is turned on.
Skip them since it doesn't make sense to push them and they cause errors with
elements that expect RTCP packets to contain data (like srtpenc).
When seeking back to restore the mdat position a flush is pushed
through and it resets downstream segment information. Make sure
that after the flush (that does a soft reset) a segment will
be pushed again
Fixes regressions spotted at
https://ci.gstreamer.net/job/GStreamer-master-validate/2100/
10 FourCCs generated with GST_MAKE_FOURCC() in gstqtmux.c and atoms.c
already exist in fourcc.h. Don't duplicate these and use them directly.
Plus moving 6 to fourcc.h, to centralize them all.
