Helps with debugging issues. And also remove unused variable (opcr)
This will also allow us in the future to properly detect:
* random-access location (to enable keyframe observation and
potentially seeking
* discont location (to properly handle resets)
* splice location (to properly handle new stream changes)
This is actually a workaround (we'll be skipping the upcoming section)
This will only happen for sections where the beginning is located within
the last 8 bytes of a packet (which is the minimum we need to properly
identify any section beginning).
Later we should figure out a way to store those bytes and mark that
some analysis needs to happen. The probability of this happening is
too low for me to care right now and do that fix. There is a good chance
that section will eventually be repeated and won't end up on such border.
* packet.origts is no longer used since the PCR refactoring done ages ago
* known_packet_size is a duplicate of packet_size != 0
* caps was never used outside of the packetizer
We had two issues with the previous code:
1) We were badly handling PUSI-flagged packets. We were discarding the
initial data (if pointer != 0) whereas we should have been accumulating
it with the previous data (if there was a continuity of course).
=> First series of information loss
2) We were not checking whether there were more sections after the end
of one (i.e. when the following byte was not a stuff byte).
This fixes those two issues.
Fixes#677443https://bugzilla.gnome.org/show_bug.cgi?id=677443
* Only mpeg-ts section packetization remains.
* Improve code to detect duplicated sections as early as possible
* Add FIXME for various issues that need fixing (but are not regressions)
https://bugzilla.gnome.org/show_bug.cgi?id=702724
Only create subtables when needed. It was previously creating one every
single time ... to check if one was present.
And speed up code to detect whether a subtable was already present or not.
Overall makes section pushing 2 times faster.
In some cases (NIT on highly-populated DVB-C operator for example), there
will be more than one section emitted for the same subtable and version
number.
In order not to lose those updates for the same version number, we checked
against the CRC of the previous section we parsed.
The problem is that, while it made sure we didn't lose any information, it
also meant that if the same section came back (same version, same CRC) later
on we would re-process it, re-parse it and re-emit it.
This version improves on that by keeping a list of previously observed CRC
for identical PID/subtable/version-number and will only process sections if
they really were never seen in the past (as opposed to just before).
On a 30s clip, this brings down the number of NIT section parsing from 4541
down to 663.
https://bugzilla.gnome.org/show_bug.cgi?id=614479
Sync byte scan is incorrect for M2TS streams because the timestamp 4
bytes were not included in the flush size. This can result in an
infinite loop.
Rework the scan code to be clearer and work in all cases.
descriptors are stored as a GValueArray of GString. The downside is
that there is no way to "pass" ownership of a GValue to a GValueArray
which previously resulted in expensive copy/free of the (already expensive)
GString.
Here we estimate first the size of the GValueArray, then create it,
then directly use the GValue of that array.
Speeds up total SI parsing by ~30%
When dealing with non-time based push-mode streams, we need to revert
to using the offset-based PCR/PTS estimation logic of packetizer.
This solves uses cases such as:
pushfile:// ! tsdemux
src ! queue ! tsdemux
https://bugzilla.gnome.org/show_bug.cgi?id=687178
Original code to parse satellite delivery descriptors to generate
"satellite" structures appeared to be copy & pasted from cable's code
without amending for satellite.
Also added 8PSK to dvbsrc's enum for modulation.
https://bugzilla.gnome.org/show_bug.cgi?id=654485
Conflicts:
gst/mpegdemux/gstmpegdesc.h
gst/mpegdemux/mpegtspacketizer.c
Peek as much as possible in one go. Ideally we should remove usage of
adapter altogether, but for the time being it provides a big enough
speedup (around 2 times faster per packet processed).
The overhead of creating/using 188 byte GstBuffer from GstAdapter
is too expensive.
We now peek the next packet, and provide a data/size which is only
valid until the packetizerpacket is cleared.
In addition, cleanup all the internal code to deal with that new
behaviour and remove double-checks which are no longer needed.
The section_length is now the corrected section_length (i.e. with
the additional 3 bytes).
Avoid using gst_adapter_prev_timestamp and instead track
the timestamp ourself.
