Doing so would be a regression over 1.0 and breaks the unit test.
However the result will be most likely unusable, so let's post
a warning message on the bus.
Use g_date_time seconds manipulation to allow to cover the quicktime
spec for creation_time. It uses seconds since 1904.
Both paths could be done using the generic approach of seconds since
1904 with GDateTime handling, but the first path using seconds from
1970 should be more commonly found and avoids a few objects creation and
ref/unref, so keep it there for performance.
Additionally, the code for handling seconds since 1970 changed from >
to >= because having 0 seconds since 1970 is also a valid case for that
path to handle.
https://bugzilla.gnome.org/show_bug.cgi?id=707975
The streamable property only make sense for fragmented formats.
For regular MP4, when downstream is not seekable we can't rewrite
the headers, so qtmux can only work with fast-start=TRUE, where
the headers are written finishing the file.
For fragmented MP4, when streamable is not seekable and the streamable
property is FALSE, we must enforce streamable=TRUE warning the user
about this change
https://bugzilla.gnome.org/show_bug.cgi?id=707242
The most common use case for fragmented MP4 (Dash and Smooth Streaming)
is producing streamable content (even for VOD). streamable=FALSE would only
be used to generate fragmented MP4 with and index of MOOF's that could
be reproduced without a playlist/manifest
https://bugzilla.gnome.org/show_bug.cgi?id=707242
Check for GST_SEEK_TYPE_NONE for stop poistion and only update
the stop time if it is requested. Otherwise just maintain whatever
was stored at the segment
https://bugzilla.gnome.org/show_bug.cgi?id=707530
When the segment has a defined stop position, qtdemux should check
when streams reach this position and mark those as EOS. When all
streams are EOS it will return GST_FLOW_EOS to upstream to allow
the pipeline to finish instead of continuously consume buffers
from upstream that are not useful for the segment.
https://bugzilla.gnome.org/show_bug.cgi?id=707530
When handling seeks in push mode, qtdemux converts the seek to bytes
and pushes upstream. It needs to keep track of the seek and the
subsequent segment to be able to map them back to the requested
seek time and properly preserve the segment stop of the seek.
This is done by using the start offset in bytes of the seek,
that should be the same of the segment from upstream. And this
is also backwards compatible with what qtdemux already was using.
https://bugzilla.gnome.org/show_bug.cgi?id=707530
Amendment 2 of ISO/IEC 14496-15 (AVC file format) is defining a new
structure for fragmented MP4 called "avc3". The principal difference
between AVC1 and AVC3 is the location of the codec initialisation
data (e.g. SPS, PPS). In AVC1 this data is placed in the initial
MOOV box (moov.trak.mdia.minf.stbl.stsd.avc1) but in AVC3 this data
goes in the first sample of every fragment (i.e. the first sample in
each mdat box). The principal reason for avc3 is to make it easier
for client implementations, because it removes the requirement to
insert the SPS+PPS in to the decoder pipeline every time there is a
representation change.
This commit adds support for the "avc3" atom, which is almost identical
to the "avc1" atom, except it does not contain any SPS or PPS data.
https://bugzilla.gnome.org/show_bug.cgi?id=702004
This should make decoders able to precisely push buffers until the stop
time in case they need the next keyframe to do it.
Also, according to gst_segment_clip, it should only push a buffer that
the starting ts is strictly smaller than the segment stop, so we change
the min < comparison for <=
Use the same seqnum on messages and events for derived events.
Fixed for flushes / stream-start / segment after a seek, and segment
after a segment.
Fixes#676242
cca2f555d1 introduces a regression, where the demux segment is not
reset on flush stop, so the next upstream segment event will calculate
an invalid base time on the new segment to be sent downstream.
https://bugzilla.gnome.org/show_bug.cgi?id=704255
