liveadder sometimes calculates the offsets incorrectly before adding. The
resulting errors can easily be heard when mixing silence with a sine.
I'm not sure what the exact conditions are to trigger this, but it definitively
happens when the buffers of two streams have a different duration and buffer
length and duration don't match exactly for one stream because of rounding
errors (e.g. duration=0:00:00.021333333)
I have to admit, I got lost in the math somewhere but it seems that not
rounding in gst_live_adder_length_from_duration() causes 1 sample overlaps in
consecutive buffers from the same stream.
When using gst_util_uint64_scale_int_round() instead of just truncating the
sine sound correctly again.
https://bugzilla.gnome.org/show_bug.cgi?id=708345
It is quite possible that we might get PTS/DTS before the first
PCR/Offset observation.
In order to end up with valid timestamp we wait until at least one
stream was able to get a proper running-time for any PTS/DTS.
Until then, we queue up the pending buffers to push out.
Once we see a first valid timestamp, we re-evaluate the amount of
running-time elapsed (based on returned inital running-time and amount
of data/DTS queued up) for any given stream.
Taking the biggest amount of elapsed time, we set that on the packetizer
as the initial offset and recalculate all pending buffers running-time
PTS/DTS.
Note: The buffer queueing system can also be used later on for the
dvb fast start proposal (where we queue up all stream packets before
seeing PAT/PMT and then push them once we know if they belong to the
chosen program).
This allows:
* Better duration estimation
* More accurate PCR location
* Overall more accurate running-time location and calculation
Location and values of PCR are recorded in groups (PCROffsetGroup)
with notable PCR/Offset observations in them (when bitrate changed
for example). PCR and offset are stored as 32bit values to
reduce memory usage (they are differences against that group's
first_{pcr|offset}.
Those groups each contain a global PCR offset (pcr_offset) which
indicates how far in the stream that group is.
Whenever new PCR values are observed, we store them in a sliding
window estimator (PCROffsetGroupCurrent).
When a reset/wrapover/gap is detected, we close the current group with
current values and start a new one (the pcr_offset of that new group
is also calculated).
When a notable change in bitrate is observed (+/- 10%), we record
new values in the current group. This is a compromise between
storing all PCR/offset observations and none, while at the same time
providing better information for running-time<=>offset calculation
in VBR streams.
Whenever a new non-contiguous group is start (due to seeking for example)
we re-evaluate the pcr_offset of each groups. This allows detecting as
quickly as possible PCR wrapover/reset.
When wanting to find the offset of a certain running-time, one can
iterate the groups by looking at the pcr_offset (which in essence *is*
the running-time of that group in the overall stream).
Once a group (or neighbouring groups if the running-time is between two
groups) is found, once can use the recorded values to find the most
accurate offset.
Right now this code is only used in pull-mode , but could also
be activated later on for any seekable stream, like live timeshift
with queue2.
Future improvements:
* some heuristics to "compress" the stored values in groups so as to keep
the memory usage down while still keeping a decent amount of notable
points.
* After a seek compare expected and obtained PCR/Offset and if the
difference is too big, re-calculate position with newly observed
values and seek to that more accurate position.
Note that this code will *not* provide keyframe-accurate seeking, but
will allow a much more accurate PCR/running-time/offset location on
any random stream.
For past (observed) values it will be as accurate as can be.
For future values it will be better than the current situation.
Finally the more you seek, the more accurate your positioning will be.
The previous code could enter an infinite loop because the adapter state
could get out of sync with its mapped data state after sync was lost.
The code was pretty confusing so it's been rewritten to be clearer.
The easiest way to reproduce the infinite loop is to use the breakmydata
element before tsdemux to trigger a resync.
https://bugzilla.gnome.org/show_bug.cgi?id=708161
When outputting in AVC3 stream format, the codec_data should not
contain any SPS or PPS, because they are embedded inside the stream.
In case of avc->bytestream h264parse will push the SPS and PPS from
codec_data downstream at the start of the stream, at intervals
controlled by "config-interval" and when there is a codec_data change.
In the case of avc3->bytstream h264parse detects that there is
already SPS/PPS in the stream and sets h264parse->push_codec to FALSE.
Therefore avc3->bytstream was already supported, except for the stream
type.
In the case of bystream->avc h264parse will generate codec_data caps
from the parsed SPS/PPS in the stream. However it does not remove these
SPS/PPS from the stream. bytestream->avc3 is the same as bytestream->avc
except that the codec_data must not have any SPS/PPS in it.
|--------------+-------------+-------------------|
|stream-format | SPS in-band | SPS in codec_data |
|--------------+-------------+-------------------|
| avc | maybe | always |
|--------------+-------------+-------------------|
| avc3 | always | never |
|--------------+-------------+-------------------|
Amendment 2 of ISO/IEC 14496-15 (AVC file format) is defining a new
structure for fragmented MP4 called "avc3". The principal difference
between AVC1 and AVC3 is the location of the codec initialisation
data (e.g. SPS, PPS). In AVC1 this data is placed in the initial MOOV box
(moov.trak.mdia.minf.stbl.stsd.avc1) but in AVC3 this data goes in the
first sample of every fragment.
https://bugzilla.gnome.org/show_bug.cgi?id=702004
The prog-map property of mpegtsmux only allows you to group pids together in a program.
The program number set in the PAT/PMT tables cannot be set explicitly.
This patch will set the program number according to the prog-map.
If a program id of 0 is given, the first vacant program number starting from 1 will be used.
https://bugzilla.gnome.org/show_bug.cgi?id=697239
Some streams had wrong values for the stream_id_extension, make sure
we only remember the valid ones.
For streams with PES_extension_field_length == 0, assume there's nothing
else.
For streams that state they have a TREF extension but don't have enough
data to store it, just assume it was produced by a non-compliant muxer
and skip the remaining data.
Only store remaining data in stream_id_extension_data instead of storing
data we already parse.
