We consider there's a sifnificant difference when it's larger than on second
or than half the duration of the last processed fragment in case the latter is
larger.
https://bugzilla.gnome.org/show_bug.cgi?id=754230
https://github.com/mesonbuild/meson
With contributions from:
Tim-Philipp Müller <tim@centricular.com>
Jussi Pakkanen <jpakkane@gmail.com> (original port)
Highlights of the features provided are:
* Faster builds on Linux (~40-50% faster)
* The ability to build with MSVC on Windows
* Generate Visual Studio project files
* Generate XCode project files
* Much faster builds on Windows (on-par with Linux)
* Seriously fast configure and building on embedded
... and many more. For more details see:
http://blog.nirbheek.in/2016/05/gstreamer-and-meson-new-hope.htmlhttp://blog.nirbheek.in/2016/07/building-and-developing-gstreamer-using.html
Building with Meson should work on both Linux and Windows, but may
need a few more tweaks on other operating systems.
And don't just reset everything. This makes sure that we can continue to
handle data in the following scenario:
moov: discont
moof: discont
mdat: continuous
Previously this would fail because the offset would be the accumulated offset
from moov and moof at the mdat position, while the buffer offset might be
something completely different.
As seen in the parent switch for object_type_id, the 4 possible values are
0x40, 0x66, 0x67 and 0x68. Fixing the nested switch to match these values.
Looks like it was a typo making them decimal instead of hexadecimal.
CID 1363328
Without, raw AAC can't be handled and we have some information available in
the decoder that most likely allows us to decode the stream in one way or
another. This is the same code already used by matroskademux for the same
reasons, and ffmpeg/vlc play such files just fine too by guesswork.
This is to handle cases where upstream handles the fragmented streaming in TIME
segments and sends us data with gaps within fragments. This would happen when dealing
with trick-modes.
When upstream (push-based, TIME SEGMENT) wishes to send discontinuous samples,
it must obey the following rules:
* The buffer containing the [moof] must have a valid GST_BUFFER_OFFSET
* The buffers containing the first sample after a gap:
* MUST start at the beginning of a sample,
* MUST have the DISCONT flag set,
* MUST have a valid GST_BUFFER_OFFSET relative to the beginning of the fragment.
https://bugzilla.gnome.org/show_bug.cgi?id=767354
No variables were added/removed. This was just a good excuse to:
* Comment what most variables are used for (and when)
* Order them in such a way as to show first the common variables used
in all cases, followed by those only used in push-mode
We shouldn't go through segment activation as we will only have a limited
understanding of how the whole stream timeline looks like from the moof. We
only know about the current fragment, while upstream knows about the whole
stream.
This fixes seeking in DASH streams, both for seeks after the current moof and
for seeks into the current moof. The former would fail because the moof ends
and we can't activate any segment, the latter would cause a segment that stops
at the moof end, and no further fragments would be played because we end up
being EOS.
https://bugzilla.gnome.org/show_bug.cgi?id=767071
segment_duration and media_time should be parsed based on version
of elst box. Specification defines that an elst box with version 1
has uint64 and int64 values for segment_duration and media_time,
respectively.
https://bugzilla.gnome.org/show_bug.cgi?id=766301
Properly handle edts segments for push-based operation seeking.
We only support edts that a single segment that has media at the end,
being preceeded by any number of gap segments.
This also allows the qt segment rate to be respected after seeks
https://bugzilla.gnome.org/show_bug.cgi?id=765669
Via the MPEG-4 Part 3 spec we can support the other layers too.
Also correct the samples per frame calculation for MP3 if it's MPEG-2 or
MPEG-2.5.
https://bugzilla.gnome.org/show_bug.cgi?id=765725
timescale/1 is unreliable value for framerate. Due to downstream
element usually use framerate generated by qtdemux, let it be omitted
until the framerate can be reliably calculated.
https://bugzilla.gnome.org/show_bug.cgi?id=764733
When playing a stream that has been protected by DASH CENC, playback
will fail if a seek is performed. Qtdemux produces the error "stream
is protected using cenc, but no cenc protection system information
has been found" and playback stops.
The problem is that gst_qtdemux_reset() gets called as part of the
FLUSH during a seek. This function frees the protection_system_ids
array. When gst_qtdemux_configure_protected_caps() is called after the
seek has completed, the protection_system_ids array is empty and
qtdemux is unable to create the correct output caps for the protected
stream.
This commit changes it to only free the protection_system_ids on
hard resets.
https://bugzilla.gnome.org/show_bug.cgi?id=761787
qtdemux->streams is an array, it will never evaluate to true when comparing
to NULL. Instead we want to check the number of streams to make sure the
stream is available.
https://bugzilla.gnome.org/show_bug.cgi?id=753614
CID 1358389
The PIFF data is stored in a custom UUID box which is parsed and the
crypto_info of the element is updated accordingly. This allows
downstream decryptors to process and decrypt the protected content.
https://bugzilla.gnome.org/show_bug.cgi?id=753614
If we don't find the index of the sample correctly in src_convert function,
we have to unref about the qtdemux before returning value.
So, I have modify it about instead pass qtdemux as a parameter into
src_convert function.
https://bugzilla.gnome.org/show_bug.cgi?id=763973
Currently, get_duration function always return the TRUE even though
it can't be set duration correctly. So, we need to add the else condition
about the fail case. Also, we already set the GST_CLOCK_TIME_NONE
in this function. So I have modify it which is related code in some
function.
https://bugzilla.gnome.org/show_bug.cgi?id=763968
